Home › Drivetrain · U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P07957F    Pressure Control Solenoid "C" Actuator Stuck Off

for Preparation Click here


SYSTEM DESCRIPTION

The ECM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).
The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the shift solenoid valves and transmission valve body assembly.

DTC No.
DTC Detection Condition
Trouble Area
P07957F
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
  1. ATF temperature is -10°C (14°F) or more, and the vehicle is being driven with the shift lever in D (no malfunctions are detected in the shift solenoid valves (SL1, SL2, SL3 and SL4), transmission revolution sensor (NT, NC), coolant temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)
  2. Both of the following conditions (a) and (b) are met:
    1. When the ECM commands the transaxle to shift to 2nd gear, the actual gear is shifted to 1st.
    2. When the ECM commands the transaxle to shift to 6th gear, the engine overruns.
  3. 0.5 seconds
  4. 2-trip detection logic
DTC Detection Condition 2:
  1. ATF temperature is -10°C (14°F) or more, and the vehicle is being driven with the shift lever in D (no malfunctions are detected in the shift solenoid valves (SL1, SL2, SL3 and SL4), transmission revolution sensor (NT, NC), coolant temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)
  2. When the ECM commands the transaxle to shift to 1st gear, the actual gear is shifted to 2nd.
  3. 0.8 seconds
  4. 2-trip detection logic
  1. Shift solenoid valve SL3 remains open or closed.
  2. Transmission valve body assembly is blocked.
  3. Automatic transaxle assembly (clutch, brake, gear, etc.)

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed), intermediate (counter) shaft revolution (speed) and output shaft revolution (speed), the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores a DTC.

INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transaxle are replaced (Click here).

HINT:
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Perform the D Position Shift Test inspection in Road Test (Click here).
  2. Turn the engine switch off.
  3. Perform step (1) again.
  4. Check for DTCs again (Click here).

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P07957F)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Transmission / Trouble Codes.

  1. Read the DTCs using the GTS.

    Result:
    Result
    Proceed to
    Only DTC P07957F is output
    A
    DTC P07957F and other DTCs are output
    B

HINT:
If a solenoid is stuck off, DTCs for several solenoids including the malfunctioning solenoid will be stored.



A
Go to step 3
B


2.PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION)

NOTICE:
This test should always be performed with at least 2 people.

  1. Warm up the engine.

  1. Turn the engine switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Transmission / Active Test / Control the Shift Position.

  1. Perform the Active Test according to the display on the GTS.

    HINT:
    Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem (Click here).

    Transmission 
    Tester Display
    Test Details
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operates the shift solenoid valves to allow gears to be selected manually
    1. Press "→" button: Upshift occurs
    2. Press "←" button: Downshift occurs
    Can be used to check the operation of the shift solenoid valves.
    Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
    Do not downshift at high speeds. Doing so will damage the automatic transaxle.
    [Vehicle Condition]
    50 km/h (31 mph) or less

    NOTICE:
    1. This Active Test can be performed when the vehicle is stopped.
    2. When shifting gears using the Active Test, do not operate the accelerator pedal for 2 seconds before and after shifting gears.

    HINT:
    The gear commanded by the ECM is shown in the Data List / Shift Status display on the GTS.

  1. Check the vehicle speed and gear when the engine speed is 1000 rpm.

    HINT:
    As the torque converter clutch has not engaged, it may be difficult to obtain the speeds specified for 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.


    Standard:

    1st
    2nd
    3rd
    4th
    5th
    6th
    8 to 12 km/h
    (5 to 7 mph)
    15 to 19 km/h
    (9 to 12 mph)
    21 to 25 km/h
    (13 to 16 mph)
    31 to 35 km/h
    (19 to 22 mph)
    44 to 48 km/h
    (27 to 30 mph)
    52 to 56 km/h
    (32 to 35 mph)

  1. Compare the ECM commanded gear and the actual gear.

    Result:

    Actuator Gear during Malfunction
    ECM Commanded Gear
    Proceed to
    1st
    2nd
    3rd
    4th
    5th
    6th
    Shift solenoid valve SL1
    Stuck ON
    1st
    2nd
    3rd
    4th
    4th
    4th
    A
    Stuck OFF
    N*1
    N*1
    N*1
    N*1
    5th
    6th
    Shift solenoid valve SL2
    Stuck ON
    4th
    4th
    4th
    4th
    5th
    6th
    B
    Stuck OFF
    1st
    2nd
    3rd
    1st
    N*1
    N*1
    Shift solenoid valve SL3
    Stuck ON
    2nd
    2nd
    3rd
    4th
    5th
    6th
    C
    Stuck OFF
    1st
    1st
    3rd
    4th
    5th
    N*1
    Shift solenoid valve SL4
    Stuck ON
    3rd
    3rd
    3rd
    4th
    5th
    5th
    D
    Stuck OFF
    1st
    2nd
    1st
    4th
    N*1
    6th
    Shift solenoid valve SLT
    Stuck ON
    N*2
    N*2
    N*2
    N*2
    N*2
    N*2
    E
    Stuck OFF*3
    1st
    2nd
    3rd
    4th
    5th
    6th

    HINT:
    1. *1: Neutral
    2. *2: If the shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear will be lower than the normal limit. When the engine power exceeds this limit, the engine speed will increase freely.
    3. *3: When the shift solenoid valve SLT is stuck off, gear shifting will be normal.



A
GO TO DTC CHART (DTC P07457F) (Click here)

B
GO TO DTC CHART (DTC P07757F) (Click here)

D
GO TO DTC CHART (DTC P28077F) (Click here)

E
GO TO DTC CHART (DTC P27137F) (Click here)
C


3.INSPECT SHIFT SOLENOID VALVE SL3


    C201747E01
  1. Remove the shift solenoid valve SL3.
    Text in Illustration 
    *1
    Shift Solenoid Valve SL3

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:
Valve moves and makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SL3 (Click here)
OK


4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

OK:
There is no foreign matter on each valve and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)