VEHICLE STABILITY CONTROL SYSTEM > VSC OFF Indicator Light Remains ON |

| 1.CHECK CAN COMMUNICATION SYSTEM |
Check if a CAN communication system DTC is output (Click here).
| Result | Proceed to |
| DTC is not output. | A |
| DTC is output. | B |
|
| ||||
| A | |
| 2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU connector is securely connected.
|
| ||||
| OK | |
| 3.CHECK BATTERY |
Check the battery voltage.
| Result | Proceed to |
| OK | A |
| NG (for 2GR-FE) | B |
| NG (for 2AR-FE) | C |
| NG (for 6AR-FSE) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 4.READ VALUE USING INTELLIGENT TESTER (VEHICLE STABILITY CONTROL SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| TRC/VSC Off Mode | TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF | Normal: Normal mode TRC OFF: TRC off mode Unknown: Unspecified VSC OFF: VSC off mode | - |
Using the intelligent tester, check that the switch condition displayed on the intelligent tester changes according to VSC OFF switch (vehicle stability control switch) operation.
|
| ||||
| OK | |
| 5.INSPECT COMBINATION METER ASSEMBLY |
Turn the ignition switch off.
Perform an Active Test of the combination meter assembly (meter CPU) using the intelligent tester (Click here).
Check the combination meter assembly.
|
| ||||
| OK | ||
| ||
| 6.INSPECT VEHICLE STABILITY CONTROL SWITCH |
![]() |
Turn the ignition switch off.
Disconnect the VSC OFF switch (vehicle stability control switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (+) - 3 (E) | Switch pushed | Below 1 Ω |
| 6 (+) - 3 (E) | Switch not pushed | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
| 9 (+) - 6 (E) | Switch pushed | Below 1 Ω |
| 9 (+) - 6 (E) | Switch not pushed | 10 kΩ or higher |
| *A | for TMMK Made |
| *B | for TMC, TMMR Made |
| *a | Component without harness connected (VSC OFF Switch (Vehicle Stability Control Switch)) |
| Result | Proceed to |
| OK | A |
| NG (for TMC, TMMR Made) | B |
| NG (for TMMK Made) | C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VEHICLE STABILITY CONTROL SWITCH) |
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-9 (CSW) - I177-6 (+) | Always | Below 1 Ω |
| A49-9 (CSW) - Body ground | Always | 10 kΩ or higher |
| I177-3 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A49-9 (CSW) - I208-9 (+) | Always | Below 1 Ω |
| A49-9 (CSW) - Body ground | Always | 10 kΩ or higher |
| I208-6 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||