CONDENSER > INSTALLATION |
| 1. INSTALL COOLER CONDENSER ASSEMBLY |
![]() |
Engage the 2 guides as shown in the illustration.
Install the cooler condenser assembly with the 4 bolts.
| 2. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
Remove the vinyl tape from the air conditioning tube and accessory assembly and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.
Install the O-ring to the air conditioner tube and accessory assembly.
Connect the air conditioner tube and accessory assembly to the cooler condenser assembly with the bolt.
| 3. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.
Install the O-ring to the No. 1 cooler refrigerant discharge hose.
Connect the No. 1 cooler refrigerant discharge hose to the cooler condenser assembly with the bolt.
| 4. INSTALL RADIATOR SIDE DEFLECTOR LH |
Engage the guide and 3 claws to install the radiator side deflector LH.
| 5. INSTALL RADIATOR SIDE DEFLECTOR RH |
Engage the guide and 3 claws to install the radiator side deflector RH.
| 6. INSTALL UPPER RADIATOR SUPPORT (for 2AR-FE) |
Install the 2 radiator support cushions to the radiator assembly.
Install the upper radiator support with the 5 bolts.
Engage the clamp and connect the hood lock control cable assembly to the upper radiator support.
Connect the 2 horn connectors.
| 7. INSTALL UPPER RADIATOR SUPPORT (for 2GR-FE) |
Install the 2 radiator support cushions to the radiator assembly.
Install the upper radiator support with the 5 bolts and connect the hood lock control cable clamp to the upper radiator support.
Connect the 2 connectors.
| 8. INSTALL UPPER RADIATOR SUPPORT (for 6AR-FSE) |
Install the 2 radiator support cushions to the radiator assembly.
Install the upper radiator support with the 5 bolts.
Engage the clamp and connect the hood lock control cable assembly to the upper radiator support.
Connect the 2 horn connectors.
| 9. INSTALL HOOD LOCK ASSEMBLY (for TMC, TMMR Made) |
| 10. INSTALL HOOD LOCK ASSEMBLY (for TMMK Made) |
![]() |
Apply MP grease to the sliding areas of the hood lock assembly.
Connect the hood lock control cable assembly.
Install the hood lock assembly with the 2 bolts and hood lock bolt.
w/ Engine Hood Courtesy Switch:
Connect the connector.
Install a new hood lock nut cap.
| 11. INSTALL INLET AIR CLEANER ASSEMBLY (for 2AR-FE) |
Install the inlet air cleaner with the 2 bolts.
| 12. INSTALL INLET AIR CLEANER ASSEMBLY (for 6AR-FSE) |
Install the inlet air cleaner assembly with the 2 bolts.
| 13. INSTALL INLET NO. 1 AIR CLEANER (for 2GR-FE) |
![]() |
Install the inlet No. 1 air cleaner to the intake air resonator sub-assembly.
Engage the pin to the radiator support.
| 14. INSTALL INLET NO. 2 AIR CLEANER (for 2GR-FE) |
Install the inlet No. 2 air cleaner to the air cleaner case sub-assembly with the 2 bolts.
Connect the 2 wire harness clamps and vacuum hose clamp.
| 15. INSTALL FRONT BUMPER ASSEMBLY (for TMC, TMMR Made) |
| 16. INSTALL FRONT BUMPER ASSEMBLY (for TMMK Made) |
| 17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 18. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for TMC, TMMR Made) |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100 g (3.5 oz) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| *i | +/-50 g (+/-1.76 oz) | - | - |
| 19. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for TMMK Made) |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Standard Charge Amount | *b | Mean Value in Proper Range |
| *c | Overcharged | *d | High Pressure |
| *e | Sub-cool System | *f | Refrigerant Amount |
| *g | +/-50 g (+/-1.76 oz) | - | - |
| 20. WARM UP ENGINE (for TMC, TMMR Made) |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 21. WARM UP ENGINE (for TMMK Made) |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 22. INSPECT FOR REFRIGERANT LEAK (for TMC, TMMR Made) |
After recharging the air conditioning system with refrigerant, check for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
Remove the front outer cowl top panel sub-assembly .
Remove the radiator side deflector RH .
![]() |
How to check for refrigerant leaks in pipe joints:
| *a | Check for leaks |
| *b | Halogen Leak Detector Sensor |
| *c | Distance between Sensor and Joint to be Checked: 10 mm or less |
| *d | Halogen Leak Detector Sensor Moving Speed: 25 to 50 mm/sec. |
Using a halogen leak detector, check for refrigerant leaks at the pipe joints shown in the illustration.

| *a | Area to be Checked | *b | Service Valve (High) |
| *c | Service Valve (Low) | *d | Pipe Joint |
| *e | Air Conditioner Pressure Sensor Joint | *f | Cooler Expansion Valve Joint |
| *g | Condenser Joint (Inlet) | *h | Condenser Joint (Outlet) |
| *i | Compressor Joint (Inlet) | *j | Compressor Joint (Outlet) |
![]() |
Bring the halogen leak detector sensor close to the drain cooler hose with the detector turned off, and then turn the detector on.
| *1 | Drain Cooler Hose |
| *a | Halogen Leak Detector |
Remove the blower motor with fan sub-assembly (Click here).
![]() |
Insert the halogen leak detector sensor into the air conditioning unit assembly, bring the sensor close to the No. 1 cooler evaporator sub-assembly and check for refrigerant leaks.
| *1 | No. 1 Cooler Evaporator Sub-assembly |
| *a | Halogen Leak Detector |
Install the blower motor with fan sub-assembly (Click here).
Install the radiator side deflector RH .
Install the front bumper assembly (Click here).
Install the front outer cowl top panel sub-assembly
| 25. ADJUST HOOD SUB-ASSEMBLY (for TMMK Made) |