Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

DTC    B2312    Power Window Switch Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator motor assemblies are operated by the power window regulator master switch assembly or power window regulator switch assembly. The power window regulator motor assemblies have motor, regulator and ECU functions.
This DTC is output when the ECU built into a power window regulator motor assembly and power window regulator master switch assembly determine that the power window regulator master switch assembly or power window regulator switch assembly is stuck.

Master Switch 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator master switch assembly stuck
  2. Power window regulator master switch assembly held in same position for more than 20 seconds
Power window regulator master switch assembly

D-Door Motor 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator master switch assembly stuck
  2. Power window regulator master switch assembly held in same position for more than 20 seconds
  1. Power window regulator master switch assembly
  2. Power window regulator motor assembly (for driver door)
  3. Wire harness or connector

P-Door Motor 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator master switch assembly stuck
  2. Power window regulator master switch assembly held in same position for more than 20 seconds
  1. Power window regulator master switch assembly
  2. Power window regulator motor assembly (for front passenger door)
  3. Wire harness or connector

WIRING DIAGRAM


B351360E04


INSPECTION PROCEDURE

NOTICE:
  1. DTC B2312 is stored in the power window regulator master switch assembly and in each power window regulator motor assembly.
  2. If the power window regulator motor assembly (for driver door) or power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (Click here).
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  4. The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (Click here).

HINT:
If DTC B2312 is not output again after the DTC has been cleared, the DTC was output due to the switch being held.

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2312 is not output.



NG
Go to step 2
OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE) 

2.CHECK DTC OUTPUT
  1. Check the parts which the DTCs have been output from.

    Result::
    Result
    Proceed to
    DTC output from power window regulator master switch assembly
    A
    DTC output from power window regulator motor assembly (for driver door)
    B
    DTC output from power window regulator motor assembly (for front passenger door)
    C



B
Go to step 3

C
Go to step 7
A

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)  

3.READ VALUE USING GTS (D-DOOR MOTOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / D-Door Motor / Data List.

  1. Read the Data List according to the display on the GTS.

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver door power window manual up switch signal / OFF or ON
    OFF: Driver door power window manual up switch not being operated
    ON: Driver door power window manual up switch being operated
    -
    D Door P/W Down SW
    Driver door power window manual down switch signal / OFF or ON
    OFF: Driver door power window manual down switch not being operated
    ON: Driver door power window manual down switch being operated
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))
  1. Disconnect the K15 power window regulator master switch assembly connector.

  1. Disconnect the K9 power window regulator motor assembly (for driver door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K15-4 (UP) - Body ground
    Always
    10 kΩ or higher
    K15-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    K9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    K9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Replace the power window regulator master switch assembly (Click here).


NEXT


6.CHECK FOR DTC
  1. Clear the DTCs (Click here ).

  1. Check for DTCs (Click here).

    OK:
    DTC B2312 is not output.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)
OK

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE) 

7.READ VALUE USING GTS (P-DOOR MOTOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / P-Door Motor / Data List.

  1. Read the Data List according to the display on the GTS.

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front Passenger door power window auto switch signal / OFF or ON
    OFF: Front passenger door power window auto switch not being operated
    ON: Front passenger door power window auto switch being operated
    -
    P Door P/W Up SW
    Front Passenger door power window manual up switch signal / OFF or ON
    OFF: Front passenger door power window manual up switch not being operated
    ON: Front passenger door power window manual up switch being operated
    -
    P Door P/W Down SW
    Front Passenger door power window manual down switch signal / OFF or ON
    OFF: Front passenger door power window manual down switch not being operated
    ON: Front passenger door power window manual down switch being operated
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
Go to step 8
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)  

8.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
  1. Remove the power window regulator switch assembly (Click here).

  1. Inspect the power window regulator switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR))
  1. Disconnect the J9 power window regulator motor assembly (for front passenger door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J12-5 (UP) - Body ground
    Always
    10 kΩ or higher
    J12-4 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J12-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    J9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    J9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J9-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)