Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P001100    Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1

DTC    P001200    Camshaft Position "A" - Timing Over-Retarded Bank 1

for Preparation Click here


DESCRIPTION

Refer to DTC P001013 .

DTC No.
DTC Detection Condition
Trouble Area
P001100
Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
  1. Valve timing
  2. Cam timing oil control solenoid assembly
  3. Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])
  4. Camshaft timing gear assembly
  5. Oil control valve filter
  6. ECM
P001200
Intake valve timing is stuck at a certain value when in the retard range (1 trip detection logic).
  1. Valve timing
  2. Cam timing oil control solenoid assembly
  3. Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])
  4. Camshaft timing gear assembly
  5. Oil control valve filter
  6. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, cam timing oil control solenoid assembly, camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) and camshaft timing gear assembly. The ECM sends a target duty-cycle control signal to the cam timing oil control solenoid assembly. The camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) is operated to control the oil pressure supplied to the camshaft timing gear assembly based on this signal. The camshaft timing gear assembly can advance or retard the intake camshaft.
  2. If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as the camshaft timing gear assembly stuck malfunction and stores a DTC.
  1. Example:
  2. A DTC is stored when the following conditions are met:
    1. It takes 5 seconds or more to change the valve timing by 5°CA.
    2. After the above condition is met, the cam timing oil control solenoid is forcibly activated for 10 seconds.
  3. These DTCs indicate that the camshaft timing gear assembly cannot operate properly due to a camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) malfunction or the presence of foreign matter in the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).

MONITOR STRATEGY


Required Sensors/Components (Main)
Cam timing oil control solenoid assembly
Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])
Crankshaft timing gear assembly
Required Sensors/Components (Related)
Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN


A232050E44

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 3 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: P001100 or P001200.
  13. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].

  14. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Depress the accelerator pedal by a large amount.

  15. Idle the engine for 3 minutes or more [G].
  16. Enter the following menus: Powertrain / Engine / Trouble Codes [H].
  17. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  18. Check the DTC judgment result again.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.


WIRING DIAGRAM

Refer to DTC P001013 .

INSPECTION PROCEDURE

HINT:
  1. DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.
  2. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001100 OR P001200)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P001100 or P001200 is output
    A
    DTC P001100 or P001200 and other DTCs are output
    B

    HINT:
    If any DTCs other than P001100 or P001200 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.

  1. Read the Data List while performing the Active Test with the engine idling.

    OK:

    GTS Operation
    Data List (Intake VVT Change Angle Bank 1)
    -100% to 100%
    Varies by 75 DegFR or more



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P001100 or P001200 is output
    B

    HINT:
    DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.



B
Go to step 4
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
  1. Inspect the cam timing oil control solenoid assembly (Click here).



NG
Go to step 10
OK


5.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
  1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) (Click here).



NG
Go to step 12
OK


6.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


  1. Remove the cylinder head cover sub-assembly.


    A329726E01


    Text in Illustration 
    *a
    7.45°
    *b
    32.43°
    *c
    Timing Mark
    *d
    "0" Timing Mark
    *e
    Groove
    -
    -

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

    HINT:
    If the timing marks are not at the positions shown, turn the crankshaft one revolution clockwise.

    OK:
    Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

    HINT:
    If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



NG
Go to step 8
OK


7.INSPECT OIL CONTROL VALVE FILTER


    A337607E01
  1. Remove the oil control valve filter .
    Text in Illustration 
    *1
    Oil Control Valve Filter

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



OK
Go to step 14

NG
REPLACE OIL CONTROL VALVE FILTER

8.CHECK ENGINE MECHANICAL SYSTEM
  1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P001100 or P001200 is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

10.REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
  1. Replace the cam timing oil control solenoid assembly (Click here).


NEXT


11.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
  1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) (Click here).



OK
Go to step 13

NG
Go to step 12

12.REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
  1. Replace the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) (Click here).


NEXT


13.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.

  1. Read the Data List while performing the Active Test with the engine idling.

    OK:

    GTS Operation
    Data List (Intake VVT Change Angle Bank 1)
    -100% to 100%
    Varies by 75 DegFR or more



NG
Go to step 14
OK

END 

14.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P001100 or P001200 is output
    B



B
REPLACE ECM (Click here)
A

END