Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P001107    Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Mechanical Failure

for Preparation Click here


DESCRIPTION

Refer to DTC P001013 .

DTC No.
DTC Detection Condition
Trouble Area
P001107
10° CA or greater camshaft timing gear assembly run-out maintained for 0.6 seconds or longer for 2 times (1 trip detection logic).
  1. Cam timing oil control solenoid assembly
  2. Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])
  3. Camshaft timing gear assembly
  4. ECM

MONITOR DESCRIPTION

During idling, the camshaft timing gear is locked at the center of the variable valve timing operating range by the two lock pins. The camshaft timing gear assembly run-out increases if one lock pin is stuck in the retracted position. In this case, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY


Required Sensors/Components (Main)
Cam timing oil control solenoid assembly
Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])
Crankshaft timing gear assembly
Required Sensors/Components (Related)
Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on.
  6. Start the engine.
  7. Wait 20 seconds or more.
  8. Enter the following menus: Powertrain / Engine / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P001107.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P001013 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM SIMULATION TEST (CHECK FOR ABNORMAL NOISE)
  1. Start the engine.

  1. Check for abnormal noise (rattling sounds) from the camshaft timing gear assembly with the engine idling.

    Result:

    Result
    Proceed to
    Abnormal noise (rattling sound) from the camshaft timing gear assembly is heard.
    A
    Abnormal noise (rattling sound) from the camshaft timing gear assembly is not heard.
    B

    HINT:
    1. As the engine speed increases, the camshaft timing gear assembly lock pins will release and the abnormal noise (rattling sound) will disappear.
    2. Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).



B
Go to step 2
A

REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE [FOR INTAKE CAMSHAFT]) AND CAMSHAFT TIMING GEAR ASSEMBLY 

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.

  1. Read the Data List while performing the Active Test with the engine idling.

    OK:

    GTS Operation
    Data List (Intake VVT Change Angle Bank 1)
    -100% to 100%
    Varies by 75 DegFR or more



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001107)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Turn the GTS on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P001107.

  1. Check the DTC judgment result.

    Result:

    Result
    Proceed to
    NORMAL
    (DTCs are not output)
    A
    ABNORMAL
    (DTC P001107 is output)
    B



B
Go to step 4
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
  1. Inspect the cam timing oil control solenoid assembly (Click here).



NG
Go to step 6
OK


5.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
  1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) (Click here).



OK
Go to step 10

NG
Go to step 8

6.REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
  1. Replace the cam timing oil control solenoid assembly (Click here).


NEXT


7.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
  1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) (Click here).



OK
Go to step 9

NG
Go to step 8

8.REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
  1. Replace the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) (Click here).


NEXT


9.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.

  1. Read the Data List while performing the Active Test with the engine idling.

    OK:

    GTS Operation
    Data List (Intake VVT Change Angle Bank 1)
    -100% to 100%
    Varies by 75 DegFR or more



NG
Go to step 10
OK

END 

10.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).


NEXT


11.CHECK WHETHER DTC OUTPUT RECURS (DTC P001107)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Turn the GTS on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P001107.

  1. Check the DTC judgment result.

    Result:

    Result
    Proceed to
    NORMAL
    (DTCs are not output)
    A
    ABNORMAL
    (DTC P001107 is output)
    B



B
REPLACE ECM (Click here)
A

END