DTC P001400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 |
DTC P001500 Camshaft Position "B" - Timing Over-Retarded Bank 1 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P001400 | Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic). |
|
| P001500 | Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic). |
|
| Required Sensors/Components (Main) | Camshaft timing oil control valve assembly (for exhaust camshaft) Camshaft timing exhaust gear assembly |
| Required Sensors/Components (Related) | Camshaft position sensor Crankshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Continuous |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001400 OR P001500) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P001400 or P001500 is output | A |
| DTC P001400 or P001500 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1.
Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust camshaft) using the GTS.
| GTS Operation | Engine Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P001400 or P001500 is output | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (Click here).
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
Remove the cylinder head cover sub-assembly.

| *a | 7.45° | *b | 32.43° |
| *c | Timing Mark | *d | "0" Timing Mark |
| *e | Groove | - | - |
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
![]() |
Remove the oil control valve filter .
| *1 | Oil Control Valve Filter |
Check that the filter is not clogged.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Replace the camshaft timing exhaust gear assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P001400 or P001500 is output | B |
|
| ||||
| A | ||
| ||
| 9.CHECK ENGINE MECHANICAL SYSTEM |
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
|
| ||||
| OK | |
| 10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P001400 or P001500 is output | B |
|
| ||||
| A | ||
| ||