Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P001600    Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A

for Preparation Click here


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft, cam timing oil control solenoid assembly, camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No.
DTC Detection Condition
Trouble Area
P001600
Deviation in the crankshaft position sensor signal and camshaft sensor (for intake camshaft) signal (2 trip detection logic).
  1. Valve timing
  2. Cam timing oil control solenoid assembly
  3. Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])
  4. Camshaft timing gear assembly
  5. Oil control valve filter
  6. ECM

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the neutral position while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM stores this DTC.

MONITOR STRATEGY


Required Sensors/Components (Main)
Camshaft timing gear assembly
Required Sensors/Components (Related)
Camshaft position sensor
Crankshaft position sensor
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Engine speed
500 to 1000 rpm

CONFIRMATION DRIVING PATTERN


A197314E50

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].
  8. Enter the following menus: Powertrain / Engine / Trouble Codes [D].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P001600.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].

  13. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Idle the engine for 5 minutes or more [F].
  15. Enter the following menus: Powertrain / Engine / Trouble Codes [G].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Check the DTC judgment result.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.


INSPECTION PROCEDURE

HINT:
  1. The monitor for this DTC detects when the timing chain is shifted by one tooth or more.
  2. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P001600 is output
    A
    DTC P001600 and other DTCs are output
    B

    HINT:
    If any DTCs other than P001600 is output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Displacement angle varies.



NG
Go to step 4
OK


3.CHECK ENGINE MECHANICAL SYSTEM
  1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.



OK
Go to step 7

NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
  1. Inspect the cam timing oil control solenoid assembly (Click here).



NG
REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (Click here)
OK


5.INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
  1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT]) (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER


    A337607E01
  1. Remove the oil control valve filter .
    Text in Illustration 
    *1
    Oil Control Valve Filter

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
REPLACE OIL CONTROL VALVE FILTER
OK


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read the pending DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P001600 is output
    B



B
Go to step 8
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

8.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).


NEXT


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read the pending DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P001600 is output
    B



B
REPLACE ECM (Click here)
A

END