DTC P001700 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B |
| DTC No. | DTC Detection Condition | Trouble Area |
| P001700 | Deviation in the crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic). |
|
| Required Sensors/Components (Main) | Camshaft timing exhaust gear assembly |
| Required Sensors/Components (Related) | Camshaft position sensor Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Engine speed | 500 to 1000 rpm |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001700) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P001700 is output | A |
| DTC P001700 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1 / Data List / All Data / Exhaust VVT Change Angle Bank 1.
Perform the Active Test. Check that the displacement angle varies.
|
| ||||
| OK | |
| 3.CHECK ENGINE MECHANICAL SYSTEM |
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
|
| ||||
|
| ||||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (Click here).
|
| ||||
| OK | |
| 5.INSPECT OIL CONTROL VALVE FILTER |
![]() |
Remove the oil control valve filter .
| *1 | Oil Control Valve Filter |
Check that the filter is not clogged.
|
| ||||
| OK | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P001700 is output | B |
|
| ||||
| A | ||
| ||
| 7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Replace the camshaft timing exhaust gear assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P001700 is output | B |
|
| ||||
| A | ||
| ||