DTC P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground |
DTC P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open |
DTC P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal |
| DTC No. | DTC Detection Condition | Trouble Area |
| P034011 | The camshaft position sensor output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic). |
|
| P034015 | The camshaft position sensor output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic). |
|
| P034031 | A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic). |
|

| ECM Terminal Name | CH1: Between VV1+ and VV1- CH2: Between EV1+ and EV1- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)) |
![]() |
Disconnect the camshaft position sensor (for intake camshaft) connector.
| *a | Front view of wire harness connector (to Camshaft Position Sensor (for Intake Camshaft)) |
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E55-3 (VC) - Body ground | Engine switch on (IG) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM) |
Disconnect the camshaft position sensor (for intake camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E55-1 (VVI+) - E96-82 (VV1+) | Always | Below 1 Ω |
| E55-2 (VVI-) - E96-114 (VV1-) | Always | Below 1 Ω |
| E55-1 (VVI+) or E96-82 (VV1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E55-2 (VVI-) or E96-114 (VV1-) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)) |
![]() |
Check the camshaft position sensor (for intake camshaft) installation condition.
| *a | Clearance |
|
| ||||
| OK | |
| 4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR) |
Inspect the timing rotor of the intake camshaft.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
Remove the cylinder head cover sub-assembly.

| *a | 7.45° | *b | 32.43° |
| *c | Timing Mark | *d | "0" Timing Mark |
| *e | Groove | - | - |
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) |
Replace the camshaft position sensor (for intake camshaft) (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015 OR P034031) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P034011, P034015 or P034031 is output | A |
| DTCs are not output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK ENGINE MECHANICAL SYSTEM |
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
|
| ||||
| OK | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015 OR P034031) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P034011, P034015 or P034031 is output | A |
| DTCs are not output | B |
|
| ||||
| A | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM) |
Disconnect the camshaft position sensor (for intake camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E55-3 (VC) - E96-113 (VCV1) | Always | Below 1 Ω |
| E55-3 (VC) or E96-113 (VCV1) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||