Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P036511    Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground

DTC    P036515    Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open

DTC    P03652A    Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range

DTC    P036531    Camshaft Position Sensor "B" Bank 1 No Signal

for Preparation Click here


DESCRIPTION

The camshaft position sensor (for the exhaust camshaft) (EV1 signal) consists of a magnet and MRE (Magneto Resistance Element).
The exhaust camshaft has a timing rotor for the camshaft position sensor. When the exhaust camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.

DTC No.
DTC Detection Condition
Trouble Area
P036511
The exhaust camshaft position sensor output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
  1. Open or short in camshaft position sensor (for exhaust camshaft) circuit
  2. Camshaft position sensor (for exhaust camshaft)
  3. ECM
P036515
The exhaust camshaft position sensor output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
  1. Open or short in camshaft position sensor (for exhaust camshaft) circuit
  2. Camshaft position sensor (for exhaust camshaft)
  3. ECM
P03652A
No exhaust camshaft position sensor signal to ECM while engine cranking (1 trip detection logic).
  1. Open or short in camshaft position sensor (for exhaust camshaft) circuit
  2. Camshaft position sensor (for exhaust camshaft)
  3. Exhaust camshaft
  4. Valve timing
  5. ECM
P036531
No exhaust camshaft position sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
  1. Open or short in camshaft position sensor (for exhaust camshaft) circuit
  2. Camshaft position sensor (for exhaust camshaft)
  3. Exhaust camshaft
  4. Valve timing
  5. ECM

HINT:
Reference: Inspection using an oscilloscope .


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY


Required Sensors/Components (Main)
Exhaust camshaft position sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P036511, P036515, P03652A or P036531.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM


A255253E26


INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
  2. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))


    A338257E03
  1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Camshaft Position Sensor (for Exhaust Camshaft))

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E52-3 (VC2) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V



NG
Go to step 10
OK


2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
  1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E52-1 (VVE+) - E96-81 (EV1+)
    Always
    Below 1 Ω
    E52-2 (VVE-) - E96-112 (EV1-)
    Always
    Below 1 Ω
    E52-1 (VVE+) or E96-81 (EV1+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E52-2 (VVE-) or E96-112 (EV1-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)


    A316078E01
  1. Check the camshaft position sensor (for exhaust camshaft) installation.
    Text in Illustration 
    *a
    Clearance

    OK:
    Camshaft position sensor is installed correctly.



NG
SECURELY REINSTALL CAMSHAFT POSITION SENSOR (Click here)
OK


4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
  1. Check the timing rotor of the exhaust camshaft.

    OK:
    Camshaft timing rotor does not have any cracks or deformation.

    HINT:
    Perform "Inspection After Repair" after replacing the exhaust camshaft (Click here).



NG
REPLACE EXHAUST CAMSHAFT (Click here)
OK


5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


  1. Remove the cylinder head cover sub-assembly.


    A329726E01


    Text in Illustration 
    *a
    7.45°
    *b
    32.43°
    *c
    Timing Mark
    *d
    "0" Timing Mark
    *e
    Groove
    -
    -

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

    HINT:
    If the timing marks are not at the positions shown, turn the crankshaft one revolution clockwise.

    OK:
    Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

    HINT:
    If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



NG
Go to step 8
OK


6.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)
  1. Replace the camshaft position sensor (for exhaust camshaft) (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P036511, P036515, P03652A OR P036531)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P036511, P036515, P03652A or P036531 is output
    A
    DTCs are not output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
END
A

REPLACE ECM (Click here)  

8.CHECK ENGINE MECHANICAL SYSTEM
  1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P036511, P036515, P03652A OR P036531)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P036511, P036515, P03652A or P036531 is output
    A
    DTCs are not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)  

10.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
  1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E52-3 (VC2) - E96-111 (VCE1)
    Always
    Below 1 Ω
    E52-3 (VC2) or E96-111 (VCE1) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)