Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P040314    Exhaust Gas Recirculation "A" Control Circuit 1 Open

DTC    P140000    Exhaust Gas Recirculation "A" Control Circuit 2 Open

DTC    P140596    Exhaust Gas Recirculation "A" Control Circuit 3 Open

DTC    P141004    Exhaust Gas Recirculation "A" Control Circuit 4 Open

for Preparation Click here


DESCRIPTION

Refer to DTC P04019C .

DTC No.
DTC Detection Condition
Trouble Area
P040314
Open or short in EGR1 circuit for 1 second or more (1 trip detection logic).
  1. Open or short in EGR valve assembly circuit
  2. EGR valve assembly
  3. No. 1 integration relay
  4. ECM
P140000
Open or short in EGR2 circuit for 1 second or more (1 trip detection logic).
  1. Open or short in EGR valve assembly circuit
  2. EGR valve assembly
  3. No. 1 integration relay
  4. ECM
P140596
Open or short in EGR3 circuit for 1 second or more (1 trip detection logic).
  1. Open or short in EGR valve assembly circuit
  2. EGR valve assembly
  3. No. 1 integration relay
  4. ECM
P141004
Open or short in EGR4 circuit for 1 second or more (1 trip detection logic).
  1. Open or short in EGR valve assembly circuit
  2. EGR valve assembly
  3. No. 1 integration relay
  4. ECM

MONITOR DESCRIPTION

These DTCs are stored if an open or short in the EGR valve assembly circuit is detected.
  1. Example:
    1. If the EGR1, EGR2, EGR3 or EGR4 operation signal is off, but the step motor output signal is on, the ECM determines that there is a short in the EGR valve assembly circuit, and stores a DTC.
    2. If the EGR1, EGR2, EGR3 or EGR4 operation signal is on, and the step motor output signal is off, the ECM determines that there is an open or short in the EGR valve assembly circuit, and stores a DTC.

MONITOR STRATEGY


Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN


A215251E15

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on [A].
  6. Start the engine and warm it up [B].
  7. Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine / Trouble Codes [D].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P040314, P140000, P140596 or P141004.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM


A338259E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.

  1. Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

    NOTICE:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    Intake Manifold Absolute Pressure
    (Data List)
    Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
    (150 to 300 mmHg(abs))
    (EGR valve is fully closed)
    Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT EGR VALVE ASSEMBLY
  1. Inspect the EGR valve assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)


    A209148E23
  1. Disconnect the EGR valve assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to EGR Valve Assembly)

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E94-2 (+B1) - Body ground
    Engine switch on (IG)
    11 to 14 V
    E94-5 (+B2) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
  1. Disconnect the EGR valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E94-4 (EGR1) - E96-36 (EGR1)
    Always
    Below 1 Ω
    E94-3 (EGR2) - E96-33 (EGR2)
    Always
    Below 1 Ω
    E94-6 (EGR3) - E96-37 (EGR3)
    Always
    Below 1 Ω
    E94-1 (EGR4) - E96-32 (EGR4)
    Always
    Below 1 Ω
    E94-4 (EGR1) or E96-36 (EGR1) - Body ground and other terminals
    Always
    10 kΩ or higher
    E94-3 (EGR2) or E96-33 (EGR2) - Body ground and other terminals
    Always
    10 kΩ or higher
    E94-6 (EGR3) or E96-37 (EGR3) - Body ground and other terminals
    Always
    10 kΩ or higher
    E94-1 (EGR4) or E96-32 (EGR4) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EGR VALVE ASSEMBLY)
  1. Disconnect the EGR valve assembly connector.

  1. Disconnect the No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1A-8 - E94-2 (+B1)
    Always
    Below 1 Ω
    1A-8 - E94-5 (+B2)
    Always
    Below 1 Ω
    1A-8 or E94-2 (+B1) - Body ground and other terminals
    Always
    10 kΩ or higher
    1A-8 or E94-5 (+B2) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)