Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065342 A25A-FKS ENGINE MECHANICAL _0319522 ENGINE UNIT A

A25A-FKS ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 19100P 1.REMOVE SPARK PLUG

Hide 89615 2.REMOVE KNOCK CONTROL SENSOR

Hide 89422A 3.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 89429F 4.REMOVE ENGINE OIL TEMPERATURE SENSOR

Hide 83520 5.REMOVE OIL PRESSURE SENSOR (OIL PRESSURE SENDER GAUGE ASSEMBLY)

Hide 15250 6.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 7.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 8.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 9.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 11.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 13090E 12.REMOVE CAM TIMING CONTROL MOTOR O-RING

Hide 12108 13.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A402713

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


Hide 12108A 14.REMOVE OIL FILLER CAP GASKET

a.
A366042

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 11401G 15.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12204C 16.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 29300 17.REMOVE VACUUM PUMP ASSEMBLY

Hide 13470 18.REMOVE CRANKSHAFT PULLEY ASSEMBLY

a.
A400324C01
1.042,1.104 0.542,1.104 0.542,1.104 0.792,0.708 false 0.031,0.198 0.344,0.396 0.313,0.198 10 false *a 2.344,1.906 2.656,2.104 0.313,0.198 10 false *b 0.25,1.01 0.708,1.208 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, hold the crankshaft pulley assembly and loosen the crankshaft pulley bolt. Further loosen the crankshaft pulley bolt until 2 or 3 threads remain screwed into the crankshaft.

SST
09213-54015  
09330-00021  


b.
A400325C01
1.313,1.135 1.5,1.135 false 2.052,0.188 2.167,0.188 2.167,0.188 2.198,0.635 true 1.896,0.115 2.208,0.313 0.313,0.198 10 false *1 1.021,1.042 1.479,1.24 0.458,0.198 10 false SST 0.073,2.01 0.385,2.208 0.313,0.198 10 false *a 0.906,3.177 1.219,3.375 0.313,0.198 10 false *b
*1 Crankshaft Pulley Bolt
*a Hold
*b Turn


Using SST and the crankshaft pulley bolt, remove the crankshaft pulley assembly and crankshaft pulley bolt.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05070, 09957-04010)

HINT:

Apply lubricant to the threads and end of SST.



Hide 16331 19.REMOVE WATER OUTLET

a.
A402714

Using an 8 mm socket wrench, remove the 3 bolts, water outlet and water outlet gasket from the cylinder head sub-assembly.


Hide 16305E 20.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY

a.
A402715

Using an 8 mm socket wrench, remove the 3 bolts, outlet water by-pass sub-assembly and outlet water pipe gasket from the cylinder head sub-assembly.


Hide 11201 21.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A400326N03
0.323,0.677 0.479,0.875 0.156,0.198 10 true A 0.979,0.531 1.135,0.729 0.156,0.198 10 true A 1.833,0.542 1.99,0.74 0.156,0.198 10 true A 2.458,0.635 2.615,0.833 0.156,0.198 10 true A 0.115,0.156 0.271,0.354 0.156,0.198 10 false B 0.885,0.073 1.042,0.271 0.156,0.198 10 false B 1.708,0.052 1.865,0.25 0.156,0.198 10 false B 2.458,0.063 2.615,0.26 0.156,0.198 10 false B 3.271,0.219 3.427,0.417 0.156,0.198 10 false B 3.24,1.292 3.396,1.49 0.156,0.198 10 false B 3.156,1.833 3.313,2.031 0.156,0.198 10 false B 2.354,1.979 2.51,2.177 0.156,0.198 10 false B 1.458,1.979 1.615,2.177 0.156,0.198 10 false B 0.833,1.979 0.99,2.177 0.156,0.198 10 false B 0.281,1.979 0.438,2.177 0.156,0.198 10 false B 0.063,1.146 0.219,1.344 0.156,0.198 10 false B

Using an 8 mm socket wrench, remove the 4 bolts (A).


b.

Remove the 12 bolts (B) and cylinder head cover sub-assembly from the camshaft housing sub-assembly.


c.
A400734

Remove the 7 cylinder head cover gaskets from the cylinder head cover sub-assembly.


d.
A400327

Remove the camshaft bearing cap oil hole gasket from the No. 1 camshaft bearing cap.


Hide 11193 22.REMOVE SPARK PLUG TUBE GASKET

a.
A400328C01
1.26,0.854 1.219,1.563 1.219,1.563 1.5,1.563 true 1.594,1.469 1.906,1.667 0.313,0.198 10 true *a
*a Protective Tape


Using a screwdriver, pry out the 4 spark plug tube gaskets from the cylinder head cover sub-assembly.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12315A 23.REMOVE ENGINE MOUNTING BRACKET RH

a.
A402118

Remove the 3 bolts and engine mounting bracket RH from the No. 2 timing gear cover assembly.


Hide 12362 24.REMOVE ENGINE MOUNTING INSULATOR RH

a.
A402119

Remove the engine mounting insulator RH from the engine mounting bracket RH.


Hide 25.REMOVE STRAIGHT SCREW PLUG

a.
A400331

Using a 10 mm hexagon wrench, remove the straight screw plug from the No. 2 timing gear cover assembly.


Hide 11320A 26.REMOVE NO. 2 TIMING GEAR COVER ASSEMBLY

a.
A400735

Remove the 20 bolts.


b.

Remove the No. 2 timing gear cover assembly from the timing chain cover assembly by prying the No. 2 timing gear cover assembly with a screwdriver with its tip wrapped with protective tape.

A404914C01
2,3.938 1.417,3.448 1.417,3.448 2.063,2.813 true 5.167,2.156 5.333,1.917 5.333,1.917 5.219,1.563 true 1.125,3.344 1.365,3.542 0.24,0.198 10 true *a 5.396,1.813 5.635,2.01 0.24,0.198 10 true *a
*a Protective Tape - -


NOTICE:

Be careful not to damage the contact surfaces of the No. 2 timing gear cover assembly and timing chain cover assembly.



Hide 11301C 27.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A400330C01
1.771,1.031 1.729,0.188 1.729,0.188 1.615,0.188 true 2.302,0.917 2.469,0.302 2.469,0.302 2.625,0.302 true 1.417,0.094 1.729,0.292 0.313,0.198 10 false *a 2.698,0.208 3.01,0.406 0.313,0.198 10 false *b
*a Protective Tape
*b Wooden Block


Using a screwdriver and wooden block, pry out the timing chain cover oil seal.

NOTICE:

Do not damage the surface of the timing chain cover oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.



Hide 28.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.

Temporarily install the crankshaft pulley bolt.

A400332C01
1.271,2.469 0.823,2.99 0.823,2.99 1.135,2.927 true 6.375,2.385 6.042,2.469 6.042,2.469 6.333,2.594 true 2.156,5.76 3.427,5.76 true 0.948,0.313 1.26,0.51 0.313,0.198 10 false *a 6.167,0.365 6.479,0.563 0.313,0.198 10 false *b 0.531,2.938 0.781,3.135 0.25,0.198 10 true *d 5.76,2.365 6.01,2.563 0.25,0.198 10 true *d 1.958,5.667 2.271,5.865 0.313,0.198 10 false *1 3.896,5.177 4.115,5.375 0.219,0.198 10 true *c
*1 Crankshaft Timing Gear Key - -
*a Approximately 11.4° *b Approximately 23.7°
*c Approximately 24.3° *d Timing Mark



b.

Rotate the crankshaft clockwise and align the crankshaft timing gear key as shown in the illustration.


c.

Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.


d.

Remove the crankshaft pulley bolt.

HINT:

As the No. 2 camshaft may rotate counterclockwise strongly when the crankshaft pulley bolt is removed, use a wrench to hold the hexagonal portion of the No. 2 camshaft.



Hide 13507A 29.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

a.

Temporarily install the crankshaft pulley assembly with the crankshaft pulley bolt.


b.
A401460C01
0.521,0.531 0.677,0.531 0.677,0.531 0.885,0.583 false 1.583,1.271 1.938,1.729 1.938,1.729 2.104,1.719 true 0.25,0.448 0.708,0.646 0.458,0.198 10 false SST 2.167,1.635 2.625,1.833 0.458,0.198 10 true SST 0.813,1.646 1.125,1.844 0.313,0.198 10 false *a
*a Bolt


While holding the crankshaft pulley assembly with SST, remove the bolt.

SST
09213-54015  
09330-00021  


c.

Remove SST, the crankshaft pulley bolt and crankshaft pulley assembly.


d.
A401459C01
0.594,1.156 0.719,1.156 0.719,1.156 0.896,1.333 false 1.635,1.188 1.813,1.469 1.813,1.469 1.99,1.469 true 0.385,1.063 0.698,1.26 0.313,0.198 10 false *1 2.052,1.385 2.365,1.583 0.313,0.198 10 true *2
*1 Chain Tensioner Plate
*2 Chain Damper Spring


Remove the chain tensioner plate and chain damper spring.


e.
A400739C01
0.719,0.792 0.896,0.792 0.896,0.792 1.333,1.271 false 0.74,1.729 0.656,1.156 0.656,1.156 0.521,1.156 false 0.594,2.865 0.552,2.521 0.552,2.521 0.396,2.521 false 0.552,0.719 0.865,0.917 0.313,0.198 10 false *1 0.333,1.073 0.646,1.271 0.313,0.198 10 false *2 0.229,2.406 0.542,2.604 0.313,0.198 10 false *3
*1 Oil Pump Drive Chain Sub-assembly
*2 Oil Pump Drive Sprocket
*3 Oil Pump Drive Shaft Sprocket


Remove the oil pump drive sprocket, oil pump drive shaft sprocket and oil pump drive chain sub-assembly.


Hide 13050 30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A430089C01
1.563,1.219 1.854,0.875 1.854,0.875 2.01,0.875 true 2.073,0.792 2.385,0.99 0.313,0.198 10 true *a
*a Loosen
V113147

Turn


Hold the hexagonal portion of the No. 2 camshaft with a wrench and turn the camshaft timing gear assembly clockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and camshaft timing gear assembly.


b.
A430090C01
1.75,0.167 2.063,0.365 0.313,0.198 10 false *a
*a Hold
V113147

Turn


Using a wrench, hold the hexagonal portion of the camshaft.

NOTICE:
·

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.




c.

Using a 10 mm bi-hexagon socket wrench, remove the bolt and camshaft timing gear assembly from the camshaft.


Hide 13506 31.REMOVE CHAIN SUB-ASSEMBLY

a.
A400338

Remove the crankshaft timing sprocket and chain sub-assembly.


Hide 13540 32.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A430193

Using an 8 mm socket wrench, remove the bolt.


b.

Remove the nut and No. 1 chain tensioner assembly.

NOTICE:

Make sure that the plunger, check ball assembly and spring do not come out.



c.
A430094C01
2.156,0.729 2.427,0.313 2.427,0.313 2.573,0.313 false 2.656,0.229 2.969,0.427 0.313,0.198 10 false *a
*a Tape


Use tape to hold the plunger inside the No. 1 chain tensioner assembly.

NOTICE:
·

Make sure that the plunger, check ball assembly and spring do not come out.

·

If the No. 1 chain tensioner assembly comes apart, reinstall the parts as shown in the illustration.

A430095C01
3.552,1.552 3.708,1.552 3.708,1.552 3.969,1.135 false 3.042,0.938 3.302,0.521 3.302,0.521 3.458,0.521 false 2.24,0.854 2.5,0.438 2.5,0.438 2.656,0.438 false 1.563,0.521 1.771,0.281 1.771,0.281 1.906,0.281 false 3.354,1.469 3.667,1.667 0.313,0.198 10 false *a 3.552,0.427 3.865,0.625 0.313,0.198 10 false *b 2.74,0.354 3.052,0.552 0.313,0.198 10 false *c 1.99,0.188 2.302,0.385 0.313,0.198 10 false *d
*a Plunger *b Check ball assembly
*c Spring *d No. 1 chain tensioner assembly body





Hide 13559 33.REMOVE CHAIN TENSIONER SLIPPER

a.
A430093

Remove the bolt and chain tensioner slipper.


Hide 13561 34.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A400337

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13070A 35.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A430096

Using a wrench, hold the hexagonal portion of the No. 2 camshaft.

NOTICE:

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.



b.

Using a 5 mm hexagon socket wrench, remove the 3 bolts.


c.

Type A:

i.
A430097C01
0.802,0.708 0.948,0.708 0.948,0.708 1.156,1.177 false 0.427,1.313 0.542,1.313 0.542,1.313 0.542,1.771 false 0.604,0.615 0.917,0.813 0.313,0.198 10 false *1 0.25,1.208 0.563,1.406 0.313,0.198 10 false *2
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Timing Oil Control Valve Assembly (Exhaust Camshaft Timing Gear Bolt Assembly)


Remove the camshaft timing exhaust gear assembly and camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).



d.

Type B:

i.
A471090C01
0.802,0.708 0.948,0.708 0.948,0.708 1.115,1.219 false 0.344,1.313 0.458,1.313 0.458,1.313 0.458,1.771 false 0.604,0.615 0.917,0.813 0.313,0.198 10 false *1 0.188,1.219 0.5,1.417 0.313,0.198 10 false *2
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Timing Oil Control Valve Assembly (Exhaust Camshaft Timing Gear Bolt Assembly)


Remove the camshaft timing exhaust gear assembly and camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).



Hide 11310 36.REMOVE TIMING CHAIN COVER ASSEMBLY

a.
A400921

Remove the 19 bolts and timing chain cover assembly from the camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and oil pump assembly.


b.

Remove the timing chain cover assembly by prying between the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly with a screwdriver with its tip wrapped with protective tape.

A404915C01
2.031,2.333 1.625,2.323 1.625,2.323 1.938,1.938 true 1.521,4.323 1.688,4.323 1.688,4.323 2.01,3.979 true 4.052,4.271 4.229,4.271 4.229,4.271 4.51,3.625 true 6.229,2.292 6.125,2.292 6.125,2.292 6,2.458 true 6.219,0.896 6.135,0.896 6.135,0.896 6.01,1.063 true 1.313,2.219 1.573,2.427 0.26,0.208 10 true *a 1.333,4.208 1.594,4.417 0.26,0.208 10 false *a 3.865,4.167 4.125,4.375 0.26,0.208 10 false *a 6.26,2.198 6.521,2.406 0.26,0.208 10 true *a 6.271,0.781 6.531,0.99 0.26,0.208 10 true *a
*a Protective Tape - -


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and timing chain cover assembly.



Hide 15703A 37.REMOVE OIL NOZZLE VALVE SUB-ASSEMBLY

a.
A400922

Remove the oil nozzle valve sub-assembly from the cylinder block sub-assembly.


Hide 13471A 38.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A401230C01
0.917,1.219 0.542,0.781 0.542,0.781 0.385,0.781 true 0.125,0.656 0.344,0.854 0.219,0.198 10 true *a
*a Protective Tape


Using a screwdriver, remove the 2 crankshaft timing gear keys.

NOTICE:

Be careful not to damage the crankshaft.


HINT:

Tape the screwdriver tip before use.



Hide 23477 39.REMOVE FUEL PUMP LIFTER GUIDE

a.
A402716

Using an 8 mm socket wrench, remove the 2 bolts and fuel pump lifter guide from the No. 4 camshaft bearing cap.


Hide 11103 40.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A400341N01
3.135,0.354 3.292,0.552 0.156,0.198 10 false 1 2.979,1.792 3.135,1.99 0.156,0.198 10 false 2 3.156,1 3.313,1.198 0.156,0.198 10 false 3 2.74,0.177 2.896,0.375 0.156,0.198 10 true 4 2.635,1.896 2.792,2.094 0.156,0.198 10 true 5 2.177,0.76 2.333,0.958 0.156,0.198 10 true 6 0.385,0.344 0.542,0.542 0.156,0.198 10 false 7 0.479,1.729 0.635,1.927 0.156,0.198 10 false 8 0.323,1 0.479,1.198 0.156,0.198 10 false 9 2.24,0.188 2.458,0.375 0.219,0.188 10 false 10 2.208,1.875 2.427,2.063 0.219,0.188 10 false 11 1.625,0.688 1.844,0.875 0.219,0.188 10 true 12 1.073,0.177 1.281,0.375 0.208,0.198 10 false 13 1.104,1.875 1.313,2.073 0.208,0.198 10 false 14 0.677,0.698 0.885,0.896 0.208,0.198 10 true 15 1.635,0.167 1.844,0.365 0.208,0.198 10 true 16 1.635,1.875 1.844,2.073 0.208,0.198 10 false 17 1.146,0.74 1.354,0.938 0.208,0.198 10 true 18

Uniformly loosen and remove the 18 bolts in the order shown in the illustration.


b.
A400342

Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 41.REMOVE CAMSHAFT BEARING CAP

a.
A400343C01
0.74,1.906 0.583,1.906 0.583,1.906 0.583,1.615 true 1.208,2.021 1.094,2.021 1.094,2.021 1.094,1.625 true 1.74,2.021 1.625,2.021 1.625,2.021 1.625,1.625 true 2.292,2.031 2.177,2.031 2.177,2.031 2.177,1.635 true 2.771,2.021 2.656,2.021 2.656,2.021 2.656,1.625 true 0.073,1.177 0.229,1.375 0.156,0.198 10 false 1 3,1.344 3.156,1.542 0.156,0.198 10 false 2 1.417,0.583 1.573,0.781 0.156,0.198 10 true 3 0.677,1.406 0.833,1.604 0.156,0.198 10 true 4 2.375,0.417 2.531,0.615 0.156,0.198 10 true 5 2.417,1.396 2.573,1.594 0.156,0.198 10 true 6 1.99,0.583 2.146,0.781 0.156,0.198 10 true 7 1.25,1.427 1.406,1.625 0.156,0.198 10 true 8 0.813,1.833 1.125,2.031 0.313,0.198 10 false *1 1.271,1.938 1.583,2.135 0.313,0.198 10 false *2 1.802,1.938 2.115,2.135 0.313,0.198 10 false *3 2.354,1.958 2.667,2.156 0.313,0.198 10 false *3 2.833,1.938 3.146,2.135 0.313,0.198 10 false *4
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap
*4 No. 4 Camshaft Bearing Cap


Remove the 8 bolts in the order shown in the illustration.


b.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13511 42.REMOVE CAMSHAFT

a.
A403802

Remove the camshaft from the camshaft housing sub-assembly.


Hide 13512 43.REMOVE NO. 2 CAMSHAFT

a.
A403801

Remove the No. 2 camshaft from the camshaft housing sub-assembly.


Hide 11155B 44.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the camshaft bearing cap setting ring pins unless they are being replaced.


a.
A400344

Remove the 10 camshaft bearing cap setting ring pins from the camshaft housing sub-assembly.


Hide 13801 45.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A404210

Remove the 16 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13750 46.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A404211

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13716 47.REMOVE VALVE STEM CAP

a.
A404212

Remove the 16 valve stem caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 11492B 48.REMOVE WATER SEAL PLATE

a.
A400925

Using an 8 mm socket wrench, remove the 2 bolts, water seal plate and gasket from the cylinder head sub-assembly.


Hide 11101 49.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A400296C03
0.49,1.948 0.646,2.146 0.156,0.198 10 true 1 2.927,0.24 3.083,0.438 0.156,0.198 10 true 2 0.5,0.24 0.656,0.438 0.156,0.198 10 true 3 2.875,1.958 3.031,2.156 0.156,0.198 10 true 4 1.104,1.948 1.26,2.146 0.156,0.198 10 true 5 2.281,0.323 2.438,0.521 0.156,0.198 10 true 6 1.083,0.281 1.24,0.479 0.156,0.198 10 true 7 2.281,1.927 2.438,2.125 0.156,0.198 10 true 8 1.667,0.302 1.823,0.5 0.156,0.198 10 true 9 1.698,1.938 1.906,2.125 0.208,0.188 10 true 10
V100136

Front of Engine


Using a 12 mm socket wrench, uniformly loosen the 10 cylinder head set bolts in the order shown in the illustration. Remove the 10 cylinder head set bolts and 10 plate washers.

NOTICE:
·

Be careful not to drop the plate washers into the cylinder head sub-assembly.

·

Warpage or cracking of the cylinder head sub-assembly may result from removing the cylinder head set bolts in the incorrect order.



HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the cylinder head sub-assembly from the cylinder block sub-assembly.


Hide 11445 51.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A400345

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.

NOTICE:

Be sure to remove the cylinder block water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block sub-assembly is inverted.



Hide 15601 52.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15600A 53.REMOVE OIL FILTER UNION

A401224

a.

Using a 12 mm straight hexagon wrench, remove the oil filter union from the stiffening crankcase assembly.


Hide 12101A 54.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket from the No. 2 oil pan sub-assembly.


Hide 12102A 55.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A400346C01
2.875,1.104 3.188,1.302 0.313,0.198 10 false *a 1.542,1.979 1.854,2.177 0.313,0.198 10 false *a
*a Nut


Remove the 11 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the No. 2 oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the stiffening crankcase assembly and No. 2 oil pan sub-assembly.

·

Be careful not to damage the No. 2 oil pan sub-assembly flange.




Hide 15104 56.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A400347

Using an 8 mm socket wrench, remove the bolt, oil strainer sub-assembly and oil strainer gasket.


Hide 89491 57.REMOVE ENGINE OIL LEVEL SENSOR

Hide 15167 58.REMOVE OIL PUMP BRACKET

a.
A401225

Remove the 2 bolts and oil pump bracket.


Hide 13411 59.INSPECT CRANKSHAFT BACKLASH

a.
A400348

Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.

Standard Backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


Maximum Backlash:

0.20 mm (0.00787 in.)


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 13620B 60.REMOVE ENGINE BALANCER ASSEMBLY

a.
A400349

Remove the 6 bolts and engine balancer assembly from the stiffening crankcase assembly.

NOTICE:

Do not disassemble the engine balancer assembly.



Hide 15100 61.REMOVE OIL PUMP ASSEMBLY

Hide 11420 62.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A400350

Remove the 7 bolts.


b.
A400351

Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly at the places shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and stiffening crankcase assembly.


HINT:

Tape the screwdriver tip before use.



Hide 63.REMOVE STRAIGHT SCREW PLUG

a.
A401226

Using a 10 mm hexagon socket wrench, remove the 3 straight screw plugs and 3 gaskets from the stiffening crankcase assembly.


Hide 64.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A404782

Remove the bolt and wire harness clamp bracket from the stiffening crankcase assembly.


Hide 65.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 66.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


Hide 67.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


Hide 11401L 68.REMOVE REAR ENGINE OIL SEAL

a.
A400360

Remove the rear engine oil seal from the cylinder block sub-assembly.