Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2017.09–2018.04
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321404 CYLINDER HEAD GASKET A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

*3: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft

(for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly

·

Replacement of ignition coil assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for U760E Initialization
(Click here)for U760E Registration
Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)
Suspension, tires*3 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 11310 1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 17167 4.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25051 5.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

Hide 22030 6.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 7.REMOVE THROTTLE BODY GASKET

Hide 17650 8.REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 23814B 9.REMOVE FUEL DELIVERY PIPE

Hide 23891 10.REMOVE FUEL DELIVERY SPACER

Hide 23291 11.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250 12.REMOVE FUEL INJECTOR ASSEMBLY

Hide 12262 13.DISCONNECT NO. 2 VENTILATION HOSE

Hide 15.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13566B 16.REMOVE TIMING CHAIN GUIDE

a.
A196878

Remove the bolt and timing chain guide.


Hide 13540 17.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A196879C19
2.635,0.542 2.51,0.542 2.51,0.542 2.25,1.052 true 1.49,0.417 1.635,0.417 1.635,0.417 1.938,1.052 true 2.677,0.458 2.854,0.615 0.177,0.156 10 true *b 1.302,0.313 1.469,0.469 0.167,0.156 10 true *a
*a Stopper Plate
*b Plunger


Allow the plunger to extend slightly, and then turn the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the No. 1 chain tensioner assembly.


b.
A196880C18
1.688,1.948 1.406,1.708 1.406,1.708 1.25,1.708 true 1.063,1.604 1.24,1.76 0.177,0.156 10 false *a
*a Pin


Move the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.


c.
A196877

Remove the 2 bolts, No. 1 chain tensioner assembly and gasket.


Hide 13559 18.REMOVE CHAIN TENSIONER SLIPPER

a.
A196876

Remove the bolt and chain tensioner slipper.


Hide 13506 19.REMOVE CHAIN SUB-ASSEMBLY

a.

Remove the chain sub-assembly.


Hide 13561 20.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A196868

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13050 21.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A407988C01
2.073,1.531 2.281,1.875 2.281,1.875 1.99,1.75 true 1.708,1.375 1.26,1.385 1.26,1.385 1.667,1.625 true 2.656,0.229 2.969,0.427 0.313,0.198 10 false *a 0.219,1.365 0.531,1.563 0.313,0.198 10 false *b 1.073,1.26 1.385,1.458 0.313,0.198 10 false *c 2.229,1.917 2.438,2.104 0.208,0.188 10 true *c
*a Hold
*b Turn
*c Do not remove


Using a wrench to hold the hexagonal portion of the camshaft, remove the bolt and camshaft timing gear assembly.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.

·

Do not remove the other 4 bolts.




Hide 13070A 22.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A407989C01
2.813,0.177 3.125,0.375 0.313,0.198 10 false *a 0.563,1.667 0.875,1.865 0.313,0.198 10 false *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, remove the bolt and camshaft timing exhaust gear assembly.

NOTICE:

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.



Hide 11103 23.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A346309N01
2.417,1.948 2.573,2.146 0.156,0.198 10 false 1 2.073,1.948 2.26,2.146 0.188,0.198 10 false 16 1.5,1.938 1.688,2.135 0.188,0.198 10 false 19 0.938,1.948 1.125,2.146 0.188,0.198 10 false 13 0.729,1.927 0.917,2.125 0.188,0.198 10 false 2 0.344,1.979 0.531,2.177 0.188,0.198 10 false 7 0.083,1.042 0.271,1.24 0.188,0.198 10 false 8 0.573,0.042 0.76,0.24 0.188,0.198 10 false 6 1.083,0.042 1.271,0.24 0.188,0.198 10 false 12 1.625,0.042 1.813,0.24 0.188,0.198 10 false 18 2.188,0.042 2.375,0.24 0.188,0.198 10 false 15 2.708,0.042 2.896,0.24 0.188,0.198 10 false 9 3.177,0.333 3.365,0.531 0.188,0.198 10 false 3 3.24,1.188 3.427,1.385 0.188,0.198 10 false 5 3.208,1.771 3.396,1.969 0.188,0.198 10 false 4 2.844,1.948 3.031,2.146 0.188,0.198 10 false 10 2.333,0.563 2.51,0.729 0.177,0.167 10 true 11 1.854,0.573 2.031,0.74 0.177,0.167 10 true 17 1.25,0.563 1.427,0.729 0.177,0.167 10 true 20 0.708,0.552 0.885,0.719 0.177,0.167 10 true 14

Uniformly loosen and remove the 20 bolts in the order shown in the illustration.


b.
A259148

Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 24.REMOVE CAMSHAFT BEARING CAP

a.
A346310C03
0.5,1.052 0.813,2.021 0.813,2.021 0.979,2.021 true 1.156,1 1.521,1.969 1.521,1.969 1.635,1.969 false 1.646,1.01 1.823,1.01 true 2.229,1 2.385,1 true 2.771,0.99 2.948,0.99 true 0.104,1.802 0.26,2 0.156,0.198 10 false 1 0.115,0.938 0.271,1.135 0.156,0.198 10 false 3 0.104,0.229 0.26,0.427 0.156,0.198 10 false 2 0.99,0.125 1.146,0.323 0.156,0.198 10 false 6 1.552,0.104 1.771,0.302 0.219,0.198 10 true 10 2.135,0.094 2.292,0.292 0.156,0.198 10 true 8 2.688,0.115 2.844,0.313 0.156,0.198 10 true 4 3.063,1.479 3.219,1.677 0.156,0.198 10 true 5 2.5,1.583 2.656,1.781 0.156,0.198 10 true 9 1.875,1.583 2.104,1.813 0.229,0.229 10 true 11 1.198,1.594 1.354,1.792 0.156,0.198 10 true 7 1.01,1.927 1.323,2.125 0.313,0.198 10 false *1 1.688,1.885 2,2.083 0.313,0.198 10 false *2 1.854,0.927 2.167,1.125 0.313,0.198 10 false *3 2.438,0.906 2.75,1.104 0.313,0.198 10 false *3 2.979,0.917 3.292,1.115 0.313,0.198 10 true *3
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap


Remove the 11 bolts in the order shown in the illustration.


b.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 15678A 25.REMOVE OIL CONTROL VALVE FILTER

Hide 11811 26.REMOVE NO. 1 CAMSHAFT BEARING

Hide 13511 27.REMOVE CAMSHAFT

a.

Remove the camshaft from the camshaft housing sub-assembly.


Hide 13512 28.REMOVE NO. 2 CAMSHAFT

a.

Remove the No. 2 camshaft from the camshaft housing sub-assembly.


Hide 11821 29.REMOVE NO. 2 CAMSHAFT BEARING

Hide 13801 30.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13750 31.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13716 32.REMOVE VALVE STEM CAP

a.

Remove the 16 valve stem caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 11101 33.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A284098N02
0.552,1.656 0.708,1.854 0.156,0.198 10 1 2.406,0.302 2.563,0.5 0.156,0.198 10 2 0.583,0.302 0.74,0.5 0.156,0.198 10 3 1.021,1.667 1.177,1.865 0.156,0.198 10 5 2.438,1.667 2.594,1.865 0.156,0.198 10 4 1.948,0.302 2.104,0.5 0.156,0.198 10 6 1.042,0.281 1.198,0.479 0.156,0.198 10 7 1.948,1.677 2.104,1.875 0.156,0.198 10 8 1.5,0.292 1.646,0.479 0.146,0.188 10 9 1.469,1.688 1.708,1.865 0.24,0.177 10 10

Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the order shown in the illustration. Remove the 10 cylinder head bolts and 10 plate washers.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the cylinder head sub-assembly.

NOTICE:
·

Be careful not to drop the plate washers into the cylinder head sub-assembly.

·

Warpage or cracking of the cylinder head sub-assembly may result from removing the cylinder head bolts in the incorrect order.




Hide 11115 34.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.