Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P0031.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>P0031

HINT:

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) Either of the following conditions is met:
1.

Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):

(a) Air fuel ratio sensor voltage is higher than 3.8 V.

(b) Heated oxygen sensor voltage is 0.21 V or higher.

2.

While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

Fuel system

·

ECM


Comes on (Euro-OBD) / - (Except Euro-OBD) DTC stored (Euro-OBD) / - (Except Euro-OBD)
P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) Either of the following conditions is met:
1.

Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):

(a) Air fuel ratio sensor voltage is less than 2.8 V.

(b) Heated oxygen sensor voltage is less than 0.69 V.

2.

While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

Fuel system

·

ECM


Comes on (Euro-OBD) / - (Except Euro-OBD) DTC stored (Euro-OBD) / - (Except Euro-OBD)

HINT:
·

When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / All Data / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the GTS.

·

The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the GTS.

·

If an air fuel ratio sensor malfunction is detected, the ECM will store a DTC.



MONITOR DESCRIPTION

Sensor Voltage Detection Monitor

Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being less than 0.69 V, the ECM stores DTC P2196. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P2195 is stored.


Sensor Current Detection Monitor

A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.

If the air fuel ratio sensor output is 2.2 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P2195 (stuck on high side). If the air fuel ratio sensor output is less than 0.7 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 (stuck on low side).


A283591E01
2.333,2.292 2.25,1.646 2.25,1.646 2.354,1.646 false 5.771,2.292 5.688,1.646 5.688,1.646 5.792,1.646 false 4.375,2.292 4.292,1.646 4.292,1.646 4.396,1.646 false 0.094,0.115 2.5,0.333 2.406,0.219 10 Air Fuel Ratio Sensor Current Monitor 2.917,0.417 6.083,0.667 3.167,0.25 10 Cumulative Time "t" = t1 + t2 = 3 seconds or more 0.646,1.063 1.25,1.333 0.604,0.271 10 Fuel-cut 0.406,2.198 1.75,2.417 1.344,0.219 10 Sensor Current (mA) 0.438,2.833 1.75,3.083 1.313,0.25 10 High Side Threshold 0.479,3.49 1.75,3.75 1.271,0.26 10 Low Side Threshold 1.469,0.938 1.75,1.167 0.281,0.229 10 ON 1.417,1.25 1.75,1.5 0.333,0.25 10 OFF 2.385,1.573 3.583,1.833 1.198,0.26 10 Delay (3 seconds) 4.427,1.573 5.583,1.833 1.156,0.26 10 Delay (3 seconds) 5.823,1.573 7,1.833 1.177,0.26 10 Delay (3 seconds) 2.417,3.646 3.667,3.917 1.25,0.271 10 3 seconds or more 2.385,4.292 3.833,4.5 1.448,0.208 10 Normal Sensor Output 4.677,4.281 6.25,4.5 1.573,0.219 10 Abnormal Sensor Output 4.688,3.865 4.938,4.115 0.25,0.25 10 t1 6.406,4.281 6.833,4.5 0.427,0.219 10 Time 6.021,3.865 6.271,4.115 0.25,0.25 10 t2

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor

TYPICAL ENABLING CONDITIONS

Sensor Voltage Detection Monitor
Time after engine start 30 seconds or more
Air fuel ratio sensor status Activated
Fuel system status Closed loop

Sensor Current Detection Monitor
Battery voltage 11 V or higher
Atmospheric pressure 76 kPa(abs) [11.02 psi(abs)] or higher
Air fuel ratio sensor status Activated
Engine coolant temperature 75°C (167°F) or higher
Continuous time of fuel cut 3 seconds or more, and less than 10 seconds

TYPICAL MALFUNCTION THRESHOLDS

P2195: Sensor Voltage Detection Monitor (Lean Side Malfunction)
Heated oxygen sensor voltage 0.21 V or higher
Air fuel ratio sensor voltage Higher than 3.8 V

P2196: Sensor Voltage Detection Monitor (Rich Side Malfunction)
Heated oxygen sensor voltage Less than 0.69 V
Air fuel ratio sensor voltage Less than 2.8 V

P2195: Sensor Current Detection Monitor (High Side Malfunction)
Air fuel ratio sensor current 2.2 mA or higher

P2196: Sensor Current Detection Monitor (Low Side Malfunction)
Air fuel ratio sensor current Less than 0.7 mA

CONFIRMATION DRIVING PATTERN

A283818E23
2.448,1.531 3.052,0.719 3.052,0.719 2.833,0.719 true 5.448,1.667 5.75,0.583 true 5.021,1.521 4.5,1.521 false 6.333,2.25 5.375,2.25 false 4.052,3.531 3.823,3.354 true 4.948,1.677 4.521,0.583 true 5.542,3.167 5.708,3.167 5.708,3.167 5.5,2.74 true 4.708,2.958 4.875,2.958 4.875,2.958 4.99,2.729 true 0.073,0.24 3.25,0.5 3.177,0.26 10 false Engine Coolant Temperature: 75°C or higher 0.156,0.865 1.104,1.094 0.948,0.229 10 false Vehicle Speed 1.156,0.604 2.885,1.031 1.729,0.427 10 false Between 60 and 100 km/h 0.719,2.281 1.167,2.583 0.448,0.302 10 false Idling 1.25,2.865 2.083,3.083 0.833,0.219 10 false Warming up 2.49,2.875 3.219,3.396 0.729,0.521 10 false 10 minutes or more 3.427,1.458 4.479,1.854 1.052,0.396 10 false 60 km/h or more 3.396,0.448 4.542,0.865 1.146,0.417 10 false Accelerator Pedal Depressed 4.667,0.708 5.667,0.917 1,0.208 10 false At least 3 times 5.823,0.438 7.052,0.958 1.229,0.521 10 false Accelerator Pedal Released (Fuel-cut) 6.417,2.146 6.979,2.51 0.563,0.365 10 false 10 km/h 6.25,2.552 6.667,2.802 0.417,0.25 10 false Time 4.375,3.073 5.604,3.344 1.229,0.271 10 false 4 seconds or more 4.094,3.469 5.417,3.667 1.323,0.198 10 false Refer to figure below 3.458,2.865 4.74,3.229 1.281,0.365 10 false 10 seconds or more 1.552,2.167 1.813,2.385 0.26,0.219 10 false [A] 2.708,1.302 2.969,1.521 0.26,0.219 10 false [B] 3.844,2.167 4.083,2.417 0.24,0.25 10 false [C] 4.99,1.302 5.25,1.521 0.26,0.219 10 false [D] 5.5,1.594 5.76,1.813 0.26,0.219 10 false [E] 6.083,3.115 6.344,3.333 0.26,0.219 10 false [F]

A268862E07
3.646,2.625 3.958,0.885 false 3.375,2.625 2.167,0.719 2.167,0.719 2.292,0.719 false 0.104,0.042 3.042,0.24 2.938,0.198 10 false Driving Pattern Detail for [C] through [E]: 0.188,0.552 1.958,0.75 1.771,0.198 10 false Reference Engine Speed 2.823,0.156 7,0.406 4.177,0.25 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 1.094,2.365 1.51,2.563 0.417,0.198 10 false Idling 2.188,2.948 2.698,3.229 0.51,0.281 10 false Idling 3.177,3.115 3.833,3.479 0.656,0.365 10 false 4 seconds or more 2.188,2.25 2.448,2.521 0.26,0.271 10 false [C] 3.031,1.146 3.313,1.469 0.281,0.323 10 false [D] 3.469,1.542 3.729,1.813 0.26,0.271 10 false [E] 2.375,0.635 3.563,0.833 1.188,0.198 10 false Delay (3 seconds) 4.01,0.75 5.448,0.948 1.438,0.198 10 false Detection Period t1 4.813,2.375 4.99,2.625 0.177,0.25 10 false t2 6.042,2.396 6.302,2.635 0.26,0.24 10 false t3 6.49,2.781 6.875,2.979 0.385,0.198 10 false Time 4.375,3.115 5.031,3.479 0.656,0.365 10 false 4 seconds or more 5.604,3.115 6.26,3.479 0.656,0.365 10 false 4 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

9.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / All Data / Idle Fuel Cut.

11.

With the shift state S selected [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

While "Idle Fuel Cut" on the Data List is ON, fuel-cut control is being executed.


13.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

14.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P2195 or P2196.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P2195 or P2196 is output A
DTC P2195 or P2196 and P0136, P0137 or P0138 are output
DTC P2195 or P2196 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?


Result:
Proceed to
YES
NO



YES

3.CLEAR DTC

NO

5.CLEAR DTC
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

c.

Input the DTC: P2195 or P2196.


d.

Check the DTC judgment.


Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P2195 or P2196 is output)
B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (AFS CURRENT B1S1)
6.READ VALUE USING GTS (AFS CURRENT B1S1)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1.

Powertrain > Engine and ECT > Data List
Tester Display
AFS Current B1S1
50003 234 39

b.

Check the test value of the air fuel ratio sensor output current during fuel-cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.

HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.




Result:
Result Proceed to
Within normal range
(0.7 mA or higher, and less than 2.2 mA)
A
Outside normal range
(Less than 0.7 mA, or 2.2 mA or higher)
B



A

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

16.REPLACE AIR FUEL RATIO SENSOR
7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / Coolant Temp, AFS Voltage B1S1 and O2S B1S2.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temp
AFS Voltage B1S1
O2S B1S2
50004 234 2 8,35,44

f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction
Lean/Rich Lean/Rich Normal


Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, AFS Voltage B1S1 is consistently below 3.1 V, and O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.


HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

8.CHECK INTAKE SYSTEM

B

16.REPLACE AIR FUEL RATIO SENSOR
8.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

9.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

10.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

11.INSPECT FUEL INJECTOR ASSEMBLY

NG

15.INSPECT FUEL PUMP
11.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

12.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

12.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

c.

Input the DTC: P2195 or P2196.


d.

Check the DTC judgment result.


Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P2195 or P2196 is output)
B



A

END

B

15.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE FUEL LINE

NG

16.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
17.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

c.

Input the DTC: P2195 or P2196.


d.

Check the DTC judgment result.


Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P2195 or P2196 is output)
B



A

END

B