Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351193 DIFFERENTIAL OIL SEAL A

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 53737B 1.REMOVE FRONT FENDER APRON SEAL LH

Hide 2.DRAIN AUTOMATIC TRANSAXLE FLUID

a.
C378107

Remove the refill plug and gasket from the rear transaxle cover sub-assembly.


b.
C378108

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.


c.
C378109C01
0.719,1.156 0.844,1.156 false 0.865,1.042 1.177,1.24 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


d.

Drain automatic transaxle fluid from the automatic transaxle assembly.


e.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


f.

Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



g.

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



Hide 43457 4.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 43420H 5.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C378139N01
1.115,2.417 1.385,1.854 true 0.969,2.448 1.427,2.677 0.458,0.229 10 false SST

Using SST, remove the front drive shaft oil seal LH from the transaxle case sub-assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle case sub-assembly.



Hide 43410M 6.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C378140N01
2.271,2.563 2.01,1.771 true 2.198,2.594 2.667,2.927 0.469,0.333 10 false SST

Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle housing.



Hide 43410M 7.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C378141C01
2.156,2.302 2.292,1.177 true 1.24,1.813 1.563,2.063 0.323,0.25 10 false *a 2.01,2.323 2.333,2.573 0.323,0.25 10 false SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST
09316-60012  (09316-00011)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal RH is installed in the correct direction.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 43420H 8.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C378142C01
1.479,1.177 2.854,1.177 2.854,1.177 1.813,1 true 2.875,1.802 3.052,2.042 0.177,0.24 10 true *a 2.917,1.063 3.281,1.323 0.365,0.26 10 false SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the transaxle case sub-assembly.

SST
09316-10010  
09950-70010  (09951-07150)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal LH is installed in the correct direction.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 43457 9.INSTALL DRIVE SHAFT BEARING BRACKET

Hide 12.INSPECT FOR OIL LEAK

Hide 53737B 13.INSTALL FRONT FENDER APRON SEAL LH