Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › ENGINE UNIT › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351458 ENGINE UNIT A

6AR-FSE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft

(for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of knock control sensor

·

Replacement of engine coolant temperature sensor

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump with seal assembly (for high pressure side)

·

Replacement of fuel pressure sensor (fuel delivery pipe sub-assembly) (for high pressure side)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for U761E Initialization
(Click here)for U761E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.*1 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of front bumper assembly Front television camera view adjustment
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 11452 1.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A337909

Remove the engine oil level dipstick.


b.

Remove the bolt and engine oil level dipstick guide.


c.

Remove the O-ring from the engine oil level dipstick guide.


Hide 17167 2.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25051 6.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

Hide 16361A 7.REMOVE V-RIBBED BELT

Hide 27020 8.REMOVE GENERATOR ASSEMBLY

Hide 9.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A413672

Remove the bolt and wire harness clamp bracket.


b.
A413671

Remove the bolt and wire harness clamp bracket.


c.
A413668

Remove the bolt and wire harness clamp bracket.


d.
A413669

Remove the bolt and wire harness clamp bracket.


Hide 10.REMOVE WIRE HARNESS CLAMP BRACKET

Hide 88310 11.REMOVE COMPRESSOR ASSEMBLY WITH MAGNETIC CLUTCH

a.

for Type A:

i.
E381581C01
2.094,1.677 2.156,1.938 true 2.083,1.938 2.396,2.094 0.313,0.156 10 false *a
*a Bracket
V100135

Bolt
V100136

Nut


Remove the 2 bolts and 2 nuts, and separate the bracket.


ii.
E381583

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.



b.

for Type B:

i.
E381582C01
2.063,1.646 2.146,1.938 true 2.063,1.948 2.375,2.104 0.313,0.156 10 false *a
*a Bracket


Remove the 4 bolts and separate the bracket.



c.

Remove the compressor assembly with magnetic clutch.


Hide 43457 12.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A413675

Remove the 3 bolts and drive shaft bearing bracket.


Hide 88431 13.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A210230

Remove the 4 bolts and No. 1 compressor mounting bracket.


Hide 15.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY (for Direct Injection)

Hide 23801P 17.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23021 18.REMOVE FUEL PUMP WITH SEAL SUB-ASSEMBLY

Hide 23901 19.DISCONNECT FUEL TUBE SUB-ASSEMBLY (for Port Injection)

Hide 23291 22.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 23.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 22030 24.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 25.REMOVE THROTTLE BODY GASKET

Hide 12262 26.DISCONNECT NO. 2 VENTILATION HOSE

Hide 82125N 29.REMOVE NO. 5 ENGINE WIRE

a.
A338550

Remove the 2 bolts and disconnect the No. 5 engine wire from the fuel delivery pipe (for Direct Injection).


b.

Disconnect the fuel pressure sensor connector, knock control sensor connector and 4 fuel injector set connectors.


c.

Disengage the 2 clamps and remove the No. 5 engine wire.


Hide 23807 30.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 23250E 31.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 25680 33.REMOVE EGR VALVE WITH COOLER ASSEMBLY

Hide 16620 34.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A337915

Remove the dust cover from the V-ribbed belt tensioner assembly.


b.
A337916

Remove the bolt and V-ribbed belt tensioner assembly from the water inlet housing.


Hide 16268 35.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A337910C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the bolt, 2 nuts, No. 1 water by-pass pipe and gasket.


Hide 36.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A413667

Remove the bolt and wire harness clamp bracket.


b.
A420742

Remove the bolt and wire harness clamp bracket.


Hide 16100 37.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 16321 38.REMOVE WATER INLET

Hide 16331A 39.REMOVE THERMOSTAT

Hide 15710 40.REMOVE OIL COOLER ASSEMBLY

Hide 89429F 41.REMOVE ENGINE OIL TEMPERATURE SENSOR

Hide 16323 42.REMOVE WATER INLET HOUSING

a.
A337917C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 4 bolts, nut and water inlet housing from the cylinder block sub-assembly.


b.
A343280

Remove the gasket from the cylinder block sub-assembly.


c.

Using an E6 "TORX" socket wrench, remove the 5 stud bolts from the water inlet housing.

A412645

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.