Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM J

6AR-FSE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E76
0.979,0.833 2.792,1.135 1.813,0.302 10 false from EFI-MAIN NO. 1 Fuse 0.938,1.177 2.698,1.531 1.76,0.354 10 false from EFI-MAIN NO. 1 Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit

·

VC Output Circuit

A402668E10
0.552,0.729 2.063,1.198 1.51,0.469 10 false Throttle Body with Motor Assembly 0.552,0.552 2.063,1.021 1.51,0.469 10 false C82 0.531,1.979 2.042,2.448 1.51,0.469 10 false C104 0.531,2.146 2.271,2.635 1.74,0.49 10 false Crank Position Sensor 0.531,3.385 2.167,3.896 1.635,0.51 10 false Camshaft Position Sensor (for Intake Camshaft) 0.542,3.219 2.052,3.688 1.51,0.469 10 false C17 0.531,4.708 2.167,5.219 1.635,0.51 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.542,4.542 2.052,5.01 1.51,0.469 10 false C20 0.552,6.042 2.26,6.563 1.708,0.521 10 false Manifold Absolute Pressure Sensor 0.552,5.875 2.063,6.344 1.51,0.469 10 false C106 0.563,7.354 2.094,8.083 1.531,0.729 10 false Oil Pressure Sensor (Oil Pressure Sender Gauge Assembly) 0.563,7.167 2.073,7.635 1.51,0.469 10 false C107 6.271,0.146 6.667,0.49 0.396,0.344 10 false 5 V 2.531,0.417 2.927,0.76 0.396,0.344 10 false VC 2.552,0.781 2.948,1.125 0.396,0.344 10 false E2 2.458,1.146 2.854,1.49 0.396,0.344 10 false VTA 2.417,1.51 2.813,1.854 0.396,0.344 10 false VTA2 2.51,2.031 2.906,2.375 0.396,0.344 10 false VC 2.49,2.385 2.885,2.729 0.396,0.344 10 false NE- 2.479,2.76 2.875,3.104 0.396,0.344 10 false NE+ 2.542,3.313 2.938,3.656 0.396,0.344 10 false VC 2.448,3.656 2.844,4 0.396,0.344 10 false VVI- 2.448,4.031 2.844,4.375 0.396,0.344 10 false VVI+ 2.479,4.625 2.875,4.969 0.396,0.344 10 false VC2 2.406,4.969 2.802,5.313 0.396,0.344 10 false VVE- 2.385,5.344 2.781,5.688 0.396,0.344 10 false VVE+ 2.531,5.885 2.927,6.229 0.396,0.344 10 false VC 2.51,6.625 2.906,6.969 0.396,0.344 10 false PIM 2.563,6.25 2.958,6.594 0.396,0.344 10 false E2 2.552,7.208 2.948,7.552 0.396,0.344 10 false VC 2.552,7.573 2.948,7.917 0.396,0.344 10 false E2 2.448,7.948 2.844,8.292 0.396,0.344 10 false PEO 2.865,0.302 3.26,0.646 0.396,0.344 10 false 5 2.865,0.656 3.26,1 0.396,0.344 10 false 3 2.854,1.031 3.25,1.375 0.396,0.344 10 false 6 2.854,1.385 3.25,1.729 0.396,0.344 10 false 4 2.854,1.906 3.25,2.25 0.396,0.344 10 false 1 2.854,2.271 3.25,2.615 0.396,0.344 10 false 2 2.854,2.635 3.25,2.979 0.396,0.344 10 false 3 2.854,3.188 3.25,3.531 0.396,0.344 10 false 3 2.854,3.552 3.25,3.896 0.396,0.344 10 false 2 2.844,3.906 3.24,4.25 0.396,0.344 10 false 1 2.854,4.49 3.25,4.833 0.396,0.344 10 false 3 2.854,4.865 3.25,5.208 0.396,0.344 10 false 2 2.854,5.219 3.25,5.563 0.396,0.344 10 false 1 2.854,5.76 3.25,6.104 0.396,0.344 10 false 3 2.844,6.135 3.24,6.479 0.396,0.344 10 false 1 2.854,6.49 3.25,6.833 0.396,0.344 10 false 2 2.844,7.104 3.24,7.448 0.396,0.344 10 false 3 2.844,7.448 3.24,7.792 0.396,0.344 10 false 1 2.854,7.833 3.25,8.177 0.396,0.344 10 false 2 4.885,0.417 5.281,0.76 0.396,0.344 10 false C58 4.885,0.781 5.281,1.125 0.396,0.344 10 false C58 4.885,1.146 5.281,1.49 0.396,0.344 10 false C58 4.885,1.51 5.281,1.854 0.396,0.344 10 false C58 4.875,2.021 5.271,2.365 0.396,0.344 10 false C58 4.885,2.385 5.281,2.729 0.396,0.344 10 false C58 4.885,2.75 5.281,3.094 0.396,0.344 10 false C58 4.885,3.292 5.281,3.635 0.396,0.344 10 false C58 4.875,3.656 5.271,4 0.396,0.344 10 false C58 4.885,4.021 5.281,4.365 0.396,0.344 10 false C58 4.875,4.615 5.271,4.958 0.396,0.344 10 false C58 4.885,5.875 5.281,6.219 0.396,0.344 10 false C58 4.875,4.969 5.271,5.313 0.396,0.344 10 false C58 4.875,5.333 5.271,5.677 0.396,0.344 10 false C58 4.885,6.25 5.281,6.594 0.396,0.344 10 false C58 4.885,6.615 5.281,6.958 0.396,0.344 10 false C58 4.885,7.219 5.281,7.563 0.396,0.344 10 false C58 4.885,7.573 5.281,7.917 0.396,0.344 10 false C58 4.885,7.938 5.281,8.281 0.396,0.344 10 false C58 4.875,0.219 5.271,0.563 0.396,0.344 10 false 121 4.875,0.583 5.271,0.927 0.396,0.344 10 false 120 4.875,0.958 5.271,1.302 0.396,0.344 10 false 122 4.917,1.323 5.313,1.667 0.396,0.344 10 false 88 4.875,1.823 5.271,2.167 0.396,0.344 10 false 110 4.875,2.208 5.271,2.552 0.396,0.344 10 false 109 4.917,2.573 5.313,2.917 0.396,0.344 10 false 76 4.885,3.104 5.281,3.448 0.396,0.344 10 false 113 4.875,3.479 5.271,3.823 0.396,0.344 10 false 114 4.917,3.833 5.313,4.177 0.396,0.344 10 false 82 4.865,4.417 5.26,4.76 0.396,0.344 10 false 111 4.865,4.792 5.26,5.135 0.396,0.344 10 false 112 4.917,5.156 5.313,5.5 0.396,0.344 10 false 81 4.865,5.688 5.26,6.031 0.396,0.344 10 false 138 4.885,6.063 5.281,6.406 0.396,0.344 10 false 137 4.875,6.427 5.271,6.771 0.396,0.344 10 false 106 4.875,7.021 5.271,7.365 0.396,0.344 10 false 130 4.865,7.385 5.26,7.729 0.396,0.344 10 false 129 4.906,7.76 5.302,8.104 0.396,0.344 10 false 98 5.281,0.313 5.677,0.656 0.396,0.344 10 false VCTA 5.292,0.677 5.688,1.021 0.396,0.344 10 false ETA 5.292,1.146 5.688,1.49 0.396,0.344 10 false VTA1 5.302,1.51 5.698,1.854 0.396,0.344 10 false VTA2 5.281,1.917 5.677,2.26 0.396,0.344 10 false VCNE 5.281,2.281 5.677,2.625 0.396,0.344 10 false NE- 5.292,2.74 5.688,3.083 0.396,0.344 10 false NE+ 5.281,3.188 5.677,3.531 0.396,0.344 10 false VCV1 5.292,3.552 5.688,3.896 0.396,0.344 10 false VV1- 5.292,4.031 5.688,4.375 0.396,0.344 10 false VV1+ 5.292,4.5 5.688,4.844 0.396,0.344 10 false VCE1 5.302,4.865 5.698,5.208 0.396,0.344 10 false EV1- 5.292,5.344 5.688,5.688 0.396,0.344 10 false EV1+ 5.292,5.781 5.927,6.125 0.635,0.344 10 false VCPM 5.292,6.625 5.688,6.969 0.396,0.344 10 false PIM 5.292,6.146 5.688,6.49 0.396,0.344 10 false EPIM 5.292,7.104 5.906,7.469 0.615,0.365 10 false VCPE 5.302,7.948 5.698,8.292 0.396,0.344 10 false PEO 5.302,7.479 5.823,7.771 0.521,0.292 10 false EPEO 5.74,8.438 6.135,8.781 0.396,0.344 10 false ECM

A424491E02
0.531,1.219 0.99,1.417 0.458,0.198 10 false A20 0.531,1.375 2.146,2.177 1.615,0.802 10 false Accelerator Pedal Sensor Assembly 2.365,0.917 2.979,1.115 0.615,0.198 10 false VCPA 2.385,1.271 3,1.469 0.615,0.198 10 false VCP2 2.448,1.635 2.906,1.833 0.458,0.198 10 false EPA 2.385,1.99 3,2.188 0.615,0.198 10 false EPA2 2.448,2.365 2.906,2.563 0.458,0.198 10 false VPA 2.385,2.719 3,2.917 0.615,0.198 10 false VPA2 5.302,0.802 5.917,1 0.615,0.198 10 false VCPA 5.302,1.167 5.917,1.365 0.615,0.198 10 false VCP2 5.302,1.521 5.76,1.719 0.458,0.198 10 false EPA 5.302,1.885 5.917,2.083 0.615,0.198 10 false EPA2 5.302,2.365 5.76,2.563 0.458,0.198 10 false VPA 5.302,2.719 5.917,2.917 0.615,0.198 10 false VPA2 4.906,2.719 5.365,2.917 0.458,0.198 10 false A78 4.906,0.917 5.365,1.115 0.458,0.198 10 false A78 4.906,1.281 5.365,1.479 0.458,0.198 10 false A78 4.906,1.635 5.365,1.833 0.458,0.198 10 false A78 4.906,2.01 5.365,2.208 0.458,0.198 10 false A78 4.906,2.365 5.365,2.563 0.458,0.198 10 false A78 4.938,0.719 5.25,0.917 0.313,0.198 10 false 49 4.948,1.104 5.26,1.302 0.313,0.198 10 false 52 4.948,1.458 5.26,1.656 0.313,0.198 10 false 48 4.948,1.833 5.26,2.031 0.313,0.198 10 false 51 4.958,2.198 5.271,2.396 0.313,0.198 10 false 47 4.948,2.552 5.26,2.75 0.313,0.198 10 false 50 0.542,3.604 1,3.802 0.458,0.198 10 false C30 0.542,3.75 1.854,4.313 1.313,0.563 10 false Mass Air Flow Meter Sub-assembly 2.573,3.51 2.885,3.708 0.313,0.198 10 false 5V 2.479,3.865 2.938,4.063 0.458,0.198 10 false E2G 2.563,4.24 2.875,4.438 0.313,0.198 10 false FG 2.479,4.583 2.938,4.781 0.458,0.198 10 false THA 5.302,4.594 5.76,4.792 0.458,0.198 10 false THA 5.302,3.76 5.76,3.958 0.458,0.198 10 false E2G 5.302,3.406 5.917,3.604 0.615,0.198 10 false VCVG 5.302,4.229 5.615,4.427 0.313,0.198 10 false VG 2.885,0.802 3.042,1 0.156,0.198 10 false 4 2.875,1.167 3.031,1.365 0.156,0.198 10 false 1 2.885,1.521 3.042,1.719 0.156,0.198 10 false 5 2.885,1.896 3.042,2.094 0.156,0.198 10 false 2 2.875,2.25 3.031,2.448 0.156,0.198 10 false 6 2.875,2.615 3.031,2.813 0.156,0.198 10 false 3 4.906,6.573 5.365,6.771 0.458,0.198 10 false C58 4.906,3.51 5.365,3.708 0.458,0.198 10 false C58 4.906,3.875 5.365,4.073 0.458,0.198 10 false C58 4.906,4.24 5.365,4.438 0.458,0.198 10 false C58 4.906,4.604 5.365,4.802 0.458,0.198 10 false C58 4.917,5.25 5.375,5.448 0.458,0.198 10 false C58 4.906,5.885 5.365,6.083 0.458,0.198 10 false C58 4.938,3.313 5.25,3.51 0.313,0.198 10 false 90 4.948,3.698 5.26,3.896 0.313,0.198 10 false 91 4.948,4.063 5.26,4.26 0.313,0.198 10 false 92 4.948,4.427 5.26,4.625 0.313,0.198 10 false 94 2.875,3.396 3.031,3.594 0.156,0.198 10 false 3 2.875,3.76 3.031,3.958 0.156,0.198 10 false 2 2.875,4.125 3.031,4.323 0.156,0.198 10 false 1 2.885,4.479 3.042,4.677 0.156,0.198 10 false 4 4.896,5.052 5.354,5.25 0.458,0.198 10 false 136 4.906,5.688 5.365,5.885 0.458,0.198 10 false 135 4.906,6.375 5.365,6.573 0.458,0.198 10 false 103 2.875,5.135 3.031,5.333 0.156,0.198 10 false 1 2.875,5.781 3.031,5.979 0.156,0.198 10 false 2 2.885,6.448 3.042,6.646 0.156,0.198 10 false 3 2.552,5.24 2.865,5.438 0.313,0.198 10 false VC 2.573,5.885 2.885,6.083 0.313,0.198 10 false E2 2.552,6.563 2.865,6.76 0.313,0.198 10 false PR 5.302,6.563 5.615,6.76 0.313,0.198 10 false PR 5.302,5.792 5.76,5.99 0.458,0.198 10 false EPR 5.313,5.135 5.927,5.333 0.615,0.198 10 false VCPR 0.594,5.49 1.052,5.688 0.458,0.198 10 false F22 0.594,5.646 3.656,5.844 3.063,0.198 10 false Fuel Pressure Sensor 5.802,6.948 6.26,7.146 0.458,0.198 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 1 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 1 FUSE VOLTAGE
A402426C02
2.083,0.76 2.698,0.292 true 0.156,0.208 0.469,0.406 0.313,0.198 10 false *1 2.729,0.188 3.042,0.385 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI NO. 1 Fuse


a.

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI NO. 1 fuse) - Body ground Engine switch on (IG) 11 to 14 V


HINT:
·

Check the fuse with it installed to the engine room relay block and junction block assembly.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANK POSITION SENSOR)

B

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANK POSITION SENSOR)
a.

Disconnect the crank position sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

8.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (OIL PRESSURE SENSOR (OIL PRESSURE SENDER GAUGE ASSEMBLY))

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

9.CHECK CONNECTION BETWEEN GTS AND ECM (OIL PRESSURE SENSOR (OIL PRESSURE SENDER GAUGE ASSEMBLY))
a.

Disconnect the oil pressure sensor (oil pressure sender gauge assembly) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)

B

REPLACE OIL PRESSURE SENSOR (OIL PRESSURE SENDER GAUGE ASSEMBLY)

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

B

11.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

12.CHECK HARNESS AND CONNECTOR

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

12.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the crank position sensor connector.


d.

Disconnect the camshaft position sensor (for intake camshaft) connector.


e.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


f.

Disconnect the oil pressure sensor (oil pressure sender gauge assembly) connector.


g.

Disconnect the fuel pressure sensor connector.


h.

Disconnect the manifold absolute pressure sensor connector.


i.

Disconnect the mass air flow meter sub-assembly connector.


j.

Disconnect the ECM connectors.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-121 (VCTA) - Body ground Always 10 kΩ or higher
A78-49 (VCPA) - Body ground Always 10 kΩ or higher
A78-52 (VCP2) - Body ground Always 10 kΩ or higher
C58-110 (VCNE) - Body ground Always 10 kΩ or higher
C58-113 (VCV1) - Body ground Always 10 kΩ or higher
C58-111 (VCE1) - Body ground Always 10 kΩ or higher
C58-130 (VCPE) - Body ground Always 10 kΩ or higher
C58-136 (VCPR) - Body ground Always 10 kΩ or higher
C58-138 (VCPM) - Body ground Always 10 kΩ or higher
C58-90 (VCVG) - Body ground Always 10 kΩ or higher



l.

Remove the EFI NO. 1 fuse, EFI-MAIN NO. 2 relay and EFI-MAIN NO. 3 relay from the engine room relay block and junction block assembly.

HINT:

Remove the EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



m.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A78-2 (+B) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A78-3 (+B2) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A78-2 (+B) - Body ground Always 10 kΩ or higher
A78-3 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR