Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › 2018.04–2019.10
RM33A0E _53 Suspension _065361 FRONT SUSPENSION _0319585 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front frame assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on for 2AR-FE:(Click here)
for A25A-FKS (w/ Canister Pump Module):(Click here)
for A25A-FKS (w/o Canister Pump Module):(Click here)
for 2GR-FKS:(Click here)
for 6AR-FSE:(Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


for 2AR-FE:(Click here)
for A25A-FKS (w/ Canister Pump Module):(Click here)
for A25A-FKS (w/o Canister Pump Module):(Click here)
for 2GR-FKS:(Click here)
for 6AR-FSE:(Click here)
Replacement of automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for UA80E Initialization:(Click here)
for UA80E Registration:(Click here)
for UB80E Initialization:(Click here)
for UB80E Registration:(Click here)
for U760E Initialization:(Click here)
for U760E Registration:(Click here)
for U761E Initialization:(Click here)
for U761E Registration:(Click here)
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system for Initialization:(Click here)
for Calibration:(Click here)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system for Initialization:(Click here)
for Calibration:(Click here)
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Rack and pinion power steering gear assembly
·

Perform torque sensor zero point calibration

·

Assist Map Writing


·

DTCs are output

·

Steering effort different between turning steering wheel left and right

·

EPS warning light illuminates


(Click here)

PROCEDURE

Hide 23825 2.REMOVE FUEL DELIVERY GUARD (for A25A-FKS)

Hide 45319 4.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 6.REMOVE FRONT FRAME ASSEMBLY

a.
C379015

Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.


b.
A402196

Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.


Hide 7.REMOVE FRONT STABILIZER BAR WITH BRACKET

Hide 44250 8.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY

Hide 48069 9.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C373262

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



b.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly.


Hide 48068 10.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 17572B 11.REMOVE NO. 2 EXHAUST PIPE SUPPORT BRACKET

a.
C374335

Remove the 2 bolts and No. 2 exhaust pipe support bracket from the front frame assembly.


Hide 51227B 12.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER (for A25A-FKS, 2GR-FKS)

a.
C373263

Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.


Hide 13.REMOVE BOLT (for 2AR-FE, 6AR-FSE)

a.

Remove the 2 bolts from the front frame assembly.


Hide 52213A 14.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.


Hide 52216B 15.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.


Hide 52211J 16.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for LH Side)

a.
C374275C01
0.281,1.677 0.281,1.125 true 0.281,1.344 1.323,1.344 1.323,1.344 1.323,1.135 true 0.219,1.677 0.531,1.833 0.313,0.156 10 false *a
*a Flange


Using a chisel and hammer, kink the flange of the front suspension member body mounting front cushion as shown in the illustration.


b.

Apply lubricant to the contact surfaces of the front suspension member body mounting front cushion.


c.
C373264C01
0.781,0.76 0.875,0.76 0.875,0.76 1.417,1.25 false 2.313,2.458 2.594,2.458 2.594,2.458 2.594,0.771 false 1.927,0.771 2.792,0.771 false 0.635,0.677 0.948,0.833 0.313,0.156 10 false *1 2.833,0.688 3.292,0.885 0.458,0.198 10 false SST
*1 Front Suspension Member Body Mounting Front Cushion


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



d.
C373265C01
2.458,1.885 2.813,1.438 2.813,1.438 2.917,1.438 false 2.552,2.896 2.906,2.896 false 2.948,2.823 3.26,2.979 0.313,0.156 10 false *a 2.958,1.365 3.417,1.563 0.458,0.198 10 false SST
*a Hold
V113147

Turn


Turn the SST center bolt as shown in the illustration to create a clearance between the front suspension member body mounting front cushion and the front frame assembly.


e.

While applying lubricant to the front suspension member body mounting front cushion through the clearance, gradually remove the front suspension member body mounting front cushion.

NOTICE:
·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52211J 17.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 52217E 18.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C374276C01
0.271,1.115 0.271,1.76 true 1.302,1.115 1.302,1.271 1.302,1.271 0.271,1.271 true 0.219,1.792 0.531,1.948 0.313,0.156 10 false *a
*a Flange


Using a chisel and hammer, kink the flange of the front suspension member body mounting rear cushion LH as shown in the illustration.


b.

Apply lubricant to the contact surfaces of the front suspension member body mounting rear cushion LH.


c.
C373266C01
0.813,0.698 0.896,0.698 0.896,0.698 1.417,1.26 false 1.927,0.771 2.854,0.771 false 2.323,2.458 2.594,2.458 2.594,2.458 2.594,0.771 false 0.667,0.615 0.979,0.771 0.313,0.156 10 false *1 2.896,0.688 3.354,0.885 0.458,0.198 10 false SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



d.
C373267C01
2.438,1.875 2.771,1.344 2.771,1.344 2.844,1.344 false 2.542,2.885 3.021,2.885 false 3.052,2.802 3.365,2.958 0.313,0.156 10 false *a 2.885,1.26 3.344,1.458 0.458,0.198 10 false SST
*a Hold
V113147

Turn


Turn the SST center bolt as shown in the illustration to create a clearance between the front suspension member body mounting rear cushion LH and the front frame assembly.


e.

While applying lubricant to the front suspension member body mounting rear cushion LH through the clearance, gradually remove the front suspension member body mounting rear cushion LH.

NOTICE:
·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52215 19.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION

HINT:

Perform the same procedure as for the front suspension member body mounting rear cushion LH.


Hide 20.REMOVE HOLE PLUG

a.

for Type A:

i.

Remove the 7 hole plugs from the front frame assembly.

HINT:

There are 2 different shapes of hole plug.

C373268N01
2.125,0.375 2.281,0.573 0.156,0.198 10 false A 2.26,0.75 2.417,0.948 0.156,0.198 10 false B 2.615,0.458 2.771,0.656 0.156,0.198 10 false A 2.021,0.615 2.177,0.813 0.156,0.198 10 false A 3.219,1.448 3.375,1.646 0.156,0.198 10 false A 3.792,1.542 3.948,1.74 0.156,0.198 10 false A 4.167,1.573 4.323,1.771 0.156,0.198 10 false A




b.

for Type B:

i.

Remove the 9 hole plugs from the front frame assembly.

HINT:

There are 3 different shapes of hole plug.


C425892N01
2.125,0.375 2.281,0.573 0.156,0.198 10 false A 2.26,0.75 2.417,0.948 0.156,0.198 10 false B 2.615,0.458 2.771,0.656 0.156,0.198 10 false A 2.021,0.615 2.177,0.813 0.156,0.198 10 false A 3.198,1.479 3.354,1.677 0.156,0.198 10 false A 3.792,1.542 3.948,1.74 0.156,0.198 10 false A 4.167,1.573 4.323,1.771 0.156,0.198 10 false A 3,1.25 3.146,1.417 0.146,0.167 10 true C 3.313,1.292 3.458,1.458 0.146,0.167 10 true C