Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2018.04–2019.10
RM33A0E _51 Engine / Hybrid System _065342 A25A-FKS ENGINE MECHANICAL _0319518 CYLINDER HEAD GASKET A

A25A-FKS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
Replacement of automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UB80E Initialization
(Click here)for UB80E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 16361A 3.REMOVE V-RIBBED BELT

Hide 88310 5.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

Hide 16620D 7.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11336A 8.REMOVE TIMING GEAR COVER INSULATOR

Hide 11323C 9.REMOVE NO. 3 TIMING CHAIN COVER (w/ Cover)

Hide 16207 10.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16260 11.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

Hide 17167 12.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17141 14.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 22030 15.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 16.REMOVE THROTTLE BODY GASKET

Hide 25680 17.REMOVE EGR COOLER ASSEMBLY

Hide 25687 18.REMOVE NO. 1 EGR COOLER BRACKET

Hide 25601 19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 16279 22.REMOVE NO. 3 WATER BY-PASS PIPE

Hide 16278 23.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 17177 25.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23910A 26.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 27.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 28.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16295 29.REMOVE NO. 7 WATER BY-PASS HOSE

Hide 23800 30.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 23807V 31.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 32.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 34.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 36.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452 39.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15250 41.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 42.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 43.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 44.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 46.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 13090E 47.REMOVE CAM TIMING CONTROL MOTOR O-RING

Hide 48.DISCONNECT NO. 1 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A411195

Slide the clip and disconnect the No. 1 water by-pass hose from the cylinder block sub-assembly.


Hide 16264D 49.DISCONNECT NO. 2 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A411196

Slide the clip and disconnect the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.


Hide 29300 50.REMOVE VACUUM PUMP ASSEMBLY

Hide 13470 51.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 16305E 53.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY

Hide 11201 54.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 55.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 56.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320A 57.REMOVE NO. 2 TIMING GEAR COVER ASSEMBLY

Hide 11301C 58.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 59.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13507A 60.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

Hide 13050 61.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 63.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 64.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 65.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 66.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 67.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 23477 68.REMOVE FUEL PUMP LIFTER GUIDE

Hide 11103 69.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 73.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 74.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 76.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 77.REMOVE CYLINDER HEAD GASKET

A403803

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 78.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 79.INSPECT CYLINDER HEAD SUB-ASSEMBLY