Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › 2018.08–2021.02
RM33A0E _55 Steering _065372 STEERING GEAR / LINKAGE _0319589 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  INSTALLATION  


PROCEDURE

Hide 45319 1.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

a.

for 2GR-FKS:

i.
C369783N01
2.406,0.135 2.573,0.313 0.167,0.177 10 true 1 1.052,0.688 1.219,0.865 0.167,0.177 10 true 2

Install the steering gear heat insulator to the rack and pinion power steering gear assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



Hide 45470 2.INSTALL TIE ROD ASSEMBLY LH

a.
C369781C01
2.198,1.094 2.198,0.396 false 1.969,0.396 2.406,0.396 2.406,0.396 2.406,1.094 false 1.813,0.302 2.125,0.458 0.313,0.156 10 false *a
*a Matchmark


Install the lock nut and tie rod assembly LH to the rack and pinion power steering gear assembly until the matchmarks are aligned.

HINT:

After adjusting the toe-in, tighten the lock nut.



Hide 45460 3.INSTALL TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 44250 4.INSTALL RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.

Install the rack and pinion power steering gear assembly to the front frame assembly with the 4 bolts and 4 new nuts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 5.INSTALL FRONT STABILIZER BAR WITH BRACKET (for A25A-FKS)

a.

Install the front stabilizer bar with the 2 front stabilizer links, front No. 1 stabilizer bracket LH, front No. 1 stabilizer bracket RH and 2 front No. 1 stabilizer bar bushings to the front frame assembly.


b.
C373256C01
2.042,0.729 2.156,0.24 2.156,0.24 2.25,0.24 true 2.292,0.146 2.604,0.302 0.313,0.156 10 false *a 1,2.042 1.146,2.219 0.146,0.177 10 true A 2.25,2.24 2.396,2.417 0.146,0.177 10 true B
*a Arrow
V100136

Front of the Vehicle


Install the front No. 1 stabilizer bracket LH to the front frame assembly with the 2 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Make sure to install the front No. 1 stabilizer bracket LH with its arrow facing the front of the vehicle.

·

Temporarily tighten the bolt (B) and then fully tighten the 2 bolts in the order of (A) and (B).




c.
C402498C02
1.156,1.219 1.24,1.219 1.24,1.219 1.385,0.833 true 0.99,1.135 1.302,1.292 0.313,0.156 10 false *a 2.292,2.115 2.438,2.281 0.146,0.167 10 true A 1.073,2.281 1.219,2.448 0.146,0.167 10 true B
*a Arrow
V100136

Front of the Vehicle


Install the front No. 1 stabilizer bracket RH to the front frame assembly with the 2 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Make sure to install the front No. 1 stabilizer bracket RH with its arrow facing the front of the vehicle.

·

Temporarily tighten the bolt (B) and then fully tighten the 2 bolts in the order of (A) and (B).




Hide 6.INSTALL FRONT STABILIZER BAR WITH BRACKET (for 2GR-FKS, 2AR-FE, 6AR-FSE)

a.

Install the front stabilizer bar with the 2 front stabilizer links, front No. 1 stabilizer bracket LH, front No. 1 stabilizer bracket RH and 2 front No. 1 stabilizer bar bushings to the front frame assembly.


b.

Install the front No. 1 stabilizer bracket LH to the front frame assembly with the 2 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Make sure to install the front No. 1 stabilizer bracket LH with its arrow facing the front of the vehicle.

·

Temporarily tighten the bolt (B) and then fully tighten the 2 bolts in the order of (A) and (B).



C380748C02
2.188,0.583 2.302,0.177 2.302,0.177 2.396,0.177 true 5.615,0.583 5.729,0.177 5.729,0.177 5.823,0.177 true 0.323,0.073 0.698,0.365 0.375,0.292 12 false *A 3.771,0.073 4.167,0.375 0.396,0.302 12 false *B 2.438,0.104 2.75,0.26 0.313,0.156 10 false *a 5.865,0.104 6.177,0.26 0.313,0.156 10 false *a 1.323,1.688 1.469,1.833 0.146,0.146 10 true A 2.333,1.833 2.479,1.979 0.146,0.146 10 true B 4.74,1.698 4.885,1.844 0.146,0.146 10 true A 5.76,1.833 5.906,1.979 0.146,0.146 10 true B
*A for TMC Made *B for TMR Made
*a Arrow - -
V100136

Front of the Vehicle - -



c.

Install the front No. 1 stabilizer bracket RH to the front frame assembly with the 2 bolts.

HINT:

Perform the same procedure as for the LH side.



Hide 7.INSTALL FRONT FRAME ASSEMBLY

Hide 9.CONNECT WIRE HARNESS (for LHD)

a.

Install the wire harness to the rack and pinion power steering gear assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C375738


b.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



Hide 10.CONNECT WIRE HARNESS (for RHD)

a.

Install the wire harness to the rack and pinion power steering gear assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C379239


b.

Connect the wire harness connector to the rack and pinion power steering gear assembly.

HINT:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



Hide 45319 11.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

a.

for A25A-FKS:

i.
C369782N01
2.615,0.125 2.771,0.313 0.156,0.188 10 true 1 1.208,0.656 1.365,0.844 0.156,0.188 10 true 2

Install the steering gear heat insulator to the rack and pinion power steering gear assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



Hide 45470 13.CONNECT TIE ROD ASSEMBLY LH

a.
C369776

Connect the tie rod assembly LH to the steering knuckle LH with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


Hide 45460 14.CONNECT TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45220 15.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C369775C01
0.958,2.823 1.531,2.823 true 1.115,2.833 1.115,2.906 1.115,2.906 1.469,2.906 true 0.792,2.74 0.958,2.906 0.167,0.167 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and rack and pinion power steering gear assembly.


b.

Connect the steering intermediate shaft assembly to the rack and pinion power steering gear assembly.


c.

Install a bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 51442 16.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY (for A25A-FKS)

Hide 51441 17.INSTALL NO. 1 ENGINE UNDER COVER (for A25A-FKS)

Hide 53852K 18.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for A25A-FKS)

Hide 53851M 19.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for A25A-FKS)

Hide 20.INSTALL FRONT WHEELS

Hide 21. TORQUE SENSOR ZERO POINT CALIBRATION