The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.
53851M
1.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
53852K
2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
51441
3.REMOVE NO. 1 ENGINE UNDER COVER
4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)
5.DRAIN ENGINE COOLANT
6.REMOVE HEADLIGHT ASSEMBLY
for LED Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>REMOVAL
for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
52618
7.REMOVE FRONT LOWER BUMPER ABSORBER (w/ Air Cooled Oil Cooler)
16695A
8.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH (w/ Air Cooled Oil Cooler)
9.DISCONNECT OIL COOLER HOSE (w/ Air Cooled Oil Cooler)
32910
10.REMOVE OIL COOLER ASSEMBLY (w/ Air Cooled Oil Cooler)
88790B
11.REMOVE THERMISTOR ASSEMBLY
52611
12.REMOVE FRONT BUMPER ENERGY ABSORBER
52131A
13.REMOVE FRONT BUMPER REINFORCEMENT
53510
14.REMOVE HOOD LOCK ASSEMBLY
17750A
15.REMOVE INLET AIR CLEANER ASSEMBLY
53253B
16.REMOVE UPPER RADIATOR MOUNTING BRACKET
Disconnect the 2 horn connectors.
Remove the 2 bolts, 2 nuts and 2 upper radiator mounting brackets.
16595B
17.REMOVE NO. 1 RADIATOR AIR GUIDE LH (w/o Air Cooled Oil Cooler)
| *1 | No. 1 Radiator Air Guide LH |
| *2 | Front Radiator Side Air Guide Plate LH |
Remove the clip and disengage the claw.
Disengage the guide to remove the No. 1 radiator air guide LH with the front radiator side air guide plate LH.
16595B
18.REMOVE NO. 1 RADIATOR AIR GUIDE LH (w/ Air Cooled Oil Cooler)
Remove the clip.
Disengage the claw to remove the No. 1 radiator air guide LH.
16593B
19.REMOVE NO. 1 RADIATOR AIR GUIDE RH (w/o Air Cooled Oil Cooler)
Remove the clip and disengage the claw.
Disengage the guide to remove the No. 1 radiator air guide RH.
16593B
20.REMOVE NO. 1 RADIATOR AIR GUIDE RH (w/ Air Cooled Oil Cooler)
Remove the clip.
Disengage the claw to remove the No. 1 radiator air guide RH.
32913
21.REMOVE OIL COOLER BRACKET (w/ Air Cooled Oil Cooler)
Remove the 2 bolts.
Disengage the 2 claws to remove the oil cooler bracket.
53205
22.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Disengage the clamp to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.
Remove the 4 bolts and upper radiator support sub-assembly.
16281F
23.DISCONNECT NO. 5 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 5 water by-pass hose from the radiator assembly.
16283D
24.DISCONNECT NO. 6 WATER BY-PASS HOSE
Disconnect the No. 6 water by-pass hose from the radiator assembly.
16571C
25.DISCONNECT NO. 1 RADIATOR HOSE
Disengage the clamp and disconnect the No. 1 radiator hose from the fan with motor assembly.
Slide the clip and disconnect the No. 1 radiator hose from the radiator assembly.
32907C
26.DISCONNECT NO. 1 OIL COOLER TUBE WITHOUT HOSE SUB-ASSEMBLY (w/ Air Cooled Oil Cooler)
Remove the bolt.
Disengage the claw to disconnect the No. 1 oil cooler tube without hose sub-assembly from the fan with motor assembly.
16572D
27.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.
16400
28.REMOVE RADIATOR ASSEMBLY
Disengage the 2 claws.
Disengage the 2 guides to separate the cooler condenser assembly from the radiator assembly.
Make sure not to damage the cooler condenser assembly when separating the cooler condenser assembly.
| *a | Lock Lever |
Disengage the claw and raise the lock lever to disconnect the cooling fan motor connector as shown in the illustration.
After disconnecting the cooling fan motor connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the cooling fan motor connector.
Disengage the wire harness clamp.
Remove the radiator assembly with the fan with motor assembly from the vehicle body.
Do not apply excessive force to the cooler condenser assembly or pipe when removing the radiator assembly with the fan with motor assembly.
Disengage the 2 claws.
Disengage the 2 guides to remove the fan with motor assembly from the radiator assembly.
Do not damage the radiator assembly when removing the fan with motor assembly.
16523A
29.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16535
30.REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.