Home › Drivetrain › K120 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461775 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K120 CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with continuously variable transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 12304 1.INSTALL ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

a.
C413874N01
2.448,1.063 2.604,1.25 0.156,0.188 10 true A 1.938,1.865 2.094,2.052 0.156,0.188 10 true B 1.604,0.292 1.76,0.479 0.156,0.188 10 true C 1.385,1.865 1.542,2.052 0.156,0.188 10 true D 1.229,0.552 1.385,0.74 0.156,0.188 10 true E

Install the engine mounting bracket sub-assembly LH to the continuously variable transaxle assembly with the 5 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (D) → Fully tighten bolt (A) → Fully tighten bolt (C) → Fully tighten bolt (E)



Hide 12303 2.INSTALL REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C413873N01
2.063,1.156 2.208,1.354 0.146,0.198 10 true A 2.031,1.75 2.177,1.948 0.146,0.198 10 true B 2.031,1.49 2.177,1.688 0.146,0.198 10 true C 1.188,1.646 1.333,1.844 0.146,0.198 10 true C

Install the rear engine mounting bracket sub-assembly to the continuously variable transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (A) → Fully tighten bolt (C)



Hide 16575F 4.INSTALL NO. 3 WATER HOSE CLAMP BRACKET

a.
C413872N01
2.031,1.302 2.188,1.479 0.156,0.177 10 true A 2.01,1.646 2.167,1.823 0.156,0.177 10 true B

Install the No. 3 water hose clamp bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (A)



Hide 35150B 5.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission case plug assembly.

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the transmission case plug assembly to the continuously variable transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.



Hide 6.INSTALL BREATHER PLUG SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the breather plug sub-assembly is necessary.


a.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the breather plug.

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the breather plug cap to the breather plug.


c.

Install the breather plug sub-assembly to the continuously variable transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.



Hide 33823 7.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 8.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C413868

Install the wire harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
C413867

Install the 2 wire harness clamp brackets with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
C413866

Install the 2 wire harness clamp brackets with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82123 9.INSTALL NO. 3 ENGINE WIRE

a.

Install the No. 3 engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Engage the clamp.


Hide 10.INSTALL TRANSAXLE HOUSING TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands and then apply MP grease to the entire periphery of the lip of a new transaxle housing type T oil seal.


b.

Temporarily install the transaxle housing type T oil seal by pressing it to the installation surface of the transaxle housing by hand.

NOTICE:

Be sure to install the transaxle housing type T oil seal in the correct direction.



c.

Clean the transaxle housing type T oil seal contact surface of SST and the area around it.

SST
09309-36010  


d.
C398775C01
1.917,2.5 1.917,2.083 false 0.844,2.76 1.156,2.958 0.313,0.198 10 false *a 1.802,2.5 2.198,2.667 0.396,0.167 10 false SST
*a Depth


Using SST and a hammer, drive the transaxle housing type T oil seal in evenly, until it is even with the side surface of the transaxle housing.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Drive the transaxle housing type T oil seal in gradually, while visually checking that it is even.

·

After installation, confirm that the transaxle housing type T oil seal has been driven in until it is even with the side surface of the transaxle housing.

·

Wipe any extra grease off with your hand.




Hide 32000A 11.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C413875C01
1.323,0.458 1.823,0.167 true 2.469,0.521 2.771,0.979 true 1.833,0.052 2.146,0.208 0.313,0.156 10 false *a 2.24,0.427 2.427,0.604 0.188,0.177 10 true *b
*a Matchmark
*b Key


Set the key at the top of the drive sprocket and put a matchmark on the transaxle housing.


b.
C401100C01
1.917,1.063 2.271,1.063 true 1.75,3.146 1.938,3.333 1.938,3.333 2.083,3.333 true 1.573,0.76 2.156,0.76 2.156,0.76 2.156,1.063 true 2.313,0.958 2.521,1.198 0.208,0.24 10 true *a 2.104,3.229 2.375,3.417 0.271,0.188 10 false *b
*a Groove
*b Matchmark
V100135

MP Grease


Apply MP grease to place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C413876C01
1.302,0.698 0.448,0.24 0.448,0.24 1.313,0.531 true 2.458,1.406 1.74,1.99 1.74,1.99 2.479,1.104 true 1.563,1.927 1.875,2.083 0.313,0.156 10 false *1 0.281,0.125 0.573,0.302 0.292,0.177 10 false *a
*1 Transaxle Housing Type T Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the transaxle housing type T oil seal.




d.
C413877C01
1.333,0.531 1.594,0.219 1.594,0.219 1.74,0.219 true 1.302,1.656 1.031,1.979 1.031,1.979 0.875,1.979 true 2.479,1.094 1.76,2 1.76,2 2.479,1.406 true 1.573,1.927 1.802,2.115 0.229,0.188 10 false *1 1.781,0.115 2.042,0.313 0.26,0.198 10 false *a 0.708,1.875 0.969,2.073 0.26,0.198 10 false *a
*1 Transaxle Housing Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the transaxle housing type T oil seal.




e.
C413878C01
1.302,0.688 0.615,0.219 0.615,0.219 1.302,0.531 true 2.458,1.396 1.646,2.01 1.646,2.01 2.469,1.094 true 1.479,1.948 1.781,2.156 0.302,0.208 10 false *1 0.448,0.104 0.76,0.313 0.313,0.208 10 false *a
*1 Transaxle Housing Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the groove of the torque converter assembly into the key of the drive sprocket.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the transaxle housing type T oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C401104C01
0.688,2.844 0.865,2.844 0.865,2.844 1.063,2.313 true 0.771,0.24 0.938,0.24 0.938,0.24 1.24,0.854 true 2.344,0.99 2.51,0.99 2.51,0.99 2.604,0.75 false 2.49,1.625 2.656,1.625 2.656,1.625 2.75,1.385 false 0.604,0.146 0.792,0.354 0.188,0.208 10 false *a 0.521,2.76 0.792,2.958 0.271,0.198 10 false *b 2.292,0.219 2.469,0.438 0.177,0.219 10 false A 2.177,0.896 2.365,1.104 0.188,0.208 10 false *a 2.323,1.542 2.594,1.74 0.271,0.198 10 false *b
*a Engine Assembly Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the continuously variable transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.

NOTICE:

Make sure to deduct the thickness of the straightedge.



h.
C413879N01
2.677,0.26 2.865,0.479 0.188,0.219 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 12.INSTALL ENGINE ASSEMBLY

a.
C398751C02
1.604,0.875 2.573,0.417 true 0.948,0.99 1.26,1.146 0.313,0.156 10 false *1 2.646,0.323 2.958,0.479 0.313,0.156 10 false *a
*1 Crankshaft
*a Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C413880C01
0.74,0.5 0.938,0.677 0.198,0.177 10 true *1 2.708,0.26 2.948,0.458 0.24,0.198 10 true *1 2.354,2.385 2.51,2.583 0.156,0.198 10 false A 0.927,2.563 1.083,2.76 0.156,0.198 10 false C 0.635,3.292 0.792,3.49 0.156,0.198 10 true C 0.854,4.042 1.01,4.24 0.156,0.198 10 true C 1.198,4.427 1.365,4.604 0.167,0.177 10 false C 2.698,4.229 2.865,4.406 0.167,0.177 10 false C 2.427,4.448 2.583,4.625 0.156,0.177 10 false B 2.781,2.615 2.938,2.813 0.156,0.198 10 false A
*1 Knock Pin


Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.


c.

Install the engine assembly to the continuously variable transaxle assembly with the 8 bolts.

Torque:
Bolt (A) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (B) : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt (C) : 46 N*m (469 kgf*cm, 34 ft.*lbf)

Bolt Length:
Bolt Length
(A) 50 mm (1.97 in.)
(B) 35 mm (1.38 in.)
(C) 45 mm (1.77 in.)


NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.



HINT:
·

Bolt (A), (B): Install from the continuously variable transaxle assembly side.

·

Bolt (C): Install from the engine assembly side.




Hide 13.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12311A 16.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C413861N01
1.01,0.281 1.156,0.458 0.146,0.177 10 true A 1.083,0.875 1.229,1.052 0.146,0.177 10 true C 2.198,0.302 2.344,0.479 0.146,0.177 10 true B

Install the front engine mounting bracket to the continuously variable transaxle assembly with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)



Hide 17.INSTALL FRONT FRAME ASSEMBLY

Hide 18.CONNECT ENGINE WIRE

a.

Connect the engine wire with the 2 bolts.

C413881C01
4.26,0.417 4.573,0.573 0.313,0.156 10 false *a 0,0.156 0.156,0.313 0.156,0.156 10 false -
*a Rack and Pinion Power Steering Gear Assembly Connector - -


Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the rack and pinion power steering gear assembly connector.

NOTICE:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



c.
C413859

Engage the 3 clamps.


d.
C441512C01
2.073,1.583 2.323,1.802 0.25,0.219 10 true *b 0.333,1.344 0.583,1.563 0.25,0.219 10 true *a
*a Transmission Revolution Sensor (NT) Connector
*b Oil Pressure Sensor Connector


Engage the clamp.


e.

Connect the oil pressure sensor connector.


f.

Connect the transmission revolution sensor (NT) connector.


g.
C426993C01
0.271,1.365 0.469,1.542 0.198,0.177 10 true *a 2.188,2.771 2.375,2.938 0.188,0.167 10 true *b
*a Transmission Revolution Sensor (NSS) Connector
*b Vacuum Hose


Connect the vacuum hose.


h.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


i.

Connect the transmission revolution sensor (NSS) connector.


j.
C413882C01
0.302,3.125 0.51,3.302 0.208,0.177 10 true *a 1.125,2.073 1.302,2.24 0.177,0.167 10 true *b 2.094,3.24 2.271,3.417 0.177,0.177 10 true *c 2.521,2.344 2.698,2.51 0.177,0.167 10 true *d
*a Transmission Wire Connector
*b Shift Stroke Sensor Connector
*c Park/Neutral Position Switch Assembly Connector
*d Transmission Revolution Sensor (NOUT) Connector


Connect the transmission revolution sensor (NOUT) connector.


k.

Connect the park/neutral position switch assembly connector.


l.

Connect the shift stroke sensor connector.


m.

Connect the transmission wire connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



n.
C413855

Engage the 2 clamps.


o.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


p.
C413854C01
2.271,1.698 2.448,1.885 0.177,0.188 10 true *a
*a Engine Coolant Temperature Sensor Connector


Connect the engine coolant temperature sensor connector.


q.

Install the bolt and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


r.
C413853

Engage the 3 clamps.


s.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


t.
C441507

Engage the clamp.


u.

Connect the No. 2 engine wire to the wire harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 45319 19.INSTALL STEERING GEAR HEAT INSULATOR

Hide 33493A 20.INSTALL TRANSMISSION OIL COOLER

Hide 21.CONNECT OIL COOLER HOSE

Hide 16261G 22.CONNECT NO. 1 WATER BY-PASS HOSE

Hide 16206 23.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the water by-pass pipe sub-assembly to the continuously variable transaxle assembly with the 3 bolts.

C456281C01
4.521,1.281 4.344,0.896 4.344,0.896 4.667,1.281 true 4.823,1.604 5.135,1.76 0.313,0.156 10 false *a 6.083,1.042 6.396,1.198 0.313,0.156 10 false *b 5.552,0.646 5.865,0.802 0.313,0.156 10 false *c 6.25,1.219 6.563,1.375 0.313,0.156 10 false *d 2.24,0.656 2.375,0.844 0.135,0.188 10 true A 1.958,2.469 2.094,2.656 0.135,0.188 10 true B 2.49,1.75 2.625,1.938 0.135,0.188 10 true C 4.208,0.75 4.521,0.906 0.313,0.156 10 false *e
*a 2 to 7 mm (0.0787 to 0.276 in.) *b 120° (Claw of Clip Location)
*c Upper Side *d RH Side
*e Paint Mark - -
V100135

Clip
V100136

Bolt


Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)



b.

Connect the water by-pass pipe sub-assembly to the water by-pass outlet sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the water by-pass pipe sub-assembly until it contacts the hose stopper of the water by-pass outlet sub-assembly.

·

Make sure to align the paint mark of the water by-pass pipe sub-assembly with the paint mark of the water by-pass outlet sub-assembly.

·

Make sure that the claws of the clip are within the location shown in the illustration.




Hide 16260 24.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY) (for Heater)

Hide 16264D 25.INSTALL FLOW SHUTTING VALVE (NO. 2 WATER BY-PASS HOSE) (for CVT)

Hide 89535B 26.INSTALL TCM

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to connect all of the coolant system hoses before installing the TCM.


a.

Install the TCM to the continuously variable transaxle assembly with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Engage the clamp.


c.
C413838C01
0,0 0,0 false
V113147

Rotate in this Direction


Connect the TCM connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the TCM connector makes a click sound.



d.

Connect the engine wire to the No. 2 transmission control ECU bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 32101G 27.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Clean the threads of the 6 drive plate and torque converter assembly setting bolts.


b.
C321585C01
1.729,1.865 2.021,1.865 2.021,1.865 2.094,1.49 false 1.531,1.75 1.844,1.906 0.313,0.156 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 28.INSTALL FLYWHEEL HOUSING UNDER COVER

a.
C413884C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws and guide to install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 30.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE