The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
32000
1.INSTALL TORQUE CONVERTER ASSEMBLY
| *a | Matchmark |
| *b | Key |
Set the key at the top of the front oil pump drive gear and put a matchmark on the transaxle housing.
| *a | Groove |
| *b | Matchmark |
|
MP Grease |
Apply MP grease to place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
Do not push the torque converter assembly excessively when rotating it.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the oil pump drive gear.
Do not push the torque converter assembly excessively when rotating it.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
Clean the drive plate and torque converter assembly setting bolt holes.
Using a vernier caliper and straightedge, measure the dimension (A) shown in the illustration and check the dimension (A).
14 mm (0.5512 in.) or more
Make sure to deduct the thickness of the straightedge.
If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
Do not include the thickness of the set block.
2.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 4 wire harness clamp brackets to the automatic transaxle case sub-assembly and transmission case side cover with the 4 bolts.
Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.
Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.
35150
3.INSTALL TRANSMISSION CASE PLUG ASSEMBLY
Coat a new O-ring with Toyota Genuine ATF WS and install it to the transmission case plug assembly.
Install the transmission case plug assembly to the transaxle housing.
33823
4.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Install the No. 1 transmission control cable bracket to the automatic transaxle case sub-assembly with the 2 bolts.
33493A
5.INSTALL TRANSMISSION OIL COOLER
32907C
6.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE
| *a | 0 to 3 mm (0 to 0.118 in.) |
| *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark |
| *d | 45° (Claw of Clip Location) |
Connect the outlet No. 2 oil cooler hose to the transmission oil cooler and slide the clip to secure it.
Make sure to slide the outlet No. 2 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.
Make sure to align the paint mark of the outlet No. 2 oil cooler hose with the paint mark of the transmission oil cooler.
Make sure that the claws of the clip are within the location shown in the illustration.
| *a | 0 to 3 mm (0 to 0.118 in.) |
| *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark |
| *d | 45° (Claw of Clip Location) |
Connect the inlet No. 2 oil cooler hose to the transmission oil cooler and slide the clip to secure it.
Make sure to slide the inlet No. 2 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.
Make sure to align the paint mark of the inlet No. 2 oil cooler hose with the paint mark of the transmission oil cooler.
Make sure that the claws of the clip are within the location shown in the illustration.
| *A | w/o Air Cooled Oil Cooler |
| *B | w/ Air Cooled Oil Cooler |
Temporarily install the No. 1 oil cooler tube sub-assembly without hose to the automatic transaxle case sub-assembly with the 2 bolts.
Tighten the 2 bolts in the order shown in the illustration.
32941
7.CONNECT INLET NO. 1 OIL COOLER HOSE
32942
8.CONNECT OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)
12303
9.INSTALL REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY
Install the rear engine mounting bracket sub-assembly to the transaxle housing with the 4 bolts.
Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (A) → Fully tighten bolt (C)
12371A
10.INSTALL REAR ENGINE MOUNTING INSULATOR
12372A
11.INSTALL ENGINE MOUNTING INSULATOR LH
Install the engine mounting insulator LH to the automatic transaxle case sub-assembly with the 5 bolts.
Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A) → Fully tighten bolt (D)
30500
12.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz)
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 8 bolts shown in the illustration.
| Bolt | Length |
|---|---|
| (A) | 50 mm (1.97 in.) |
| (B) | 45 mm (1.77 in.) |
| (C) | 35 mm (1.38 in.) |
| (D) | 45 mm (1.77 in.) |
Confirm that the knock pins are installed to the automatic transaxle assembly contact surface of the cylinder block sub-assembly before installing the automatic transaxle assembly.
Do not forcibly pry on the automatic transaxle assembly.
Check that the torque converter assembly rotates.
28100
13.INSTALL STARTER ASSEMBLY (for DENSO Made)
Install the starter assembly to the cylinder block sub-assembly with the 2 bolts.
Connect the No. 2 engine wire to the terminal 30 with the nut.
Close the terminal cap.
Connect the starter assembly connector.
28100
14.INSTALL STARTER ASSEMBLY (for VALEO Made)
11363A
15.INSTALL FLYWHEEL HOUSING SIDE COVER (for DENSO Made)
11363A
16.INSTALL FLYWHEEL HOUSING SIDE COVER (for VALEO Made)
12311A
17.INSTALL FRONT ENGINE MOUNTING BRACKET
Install the front engine mounting bracket to the transaxle housing with the 3 bolts.
Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)
51100G
18.INSTALL FRONT FRAME ASSEMBLY
19.CONNECT WIRE HARNESS
Engage the wire harness clamp to connect the wire harness to the automatic transaxle assembly.
Install the 2 bolts.
for LHD:
Engage the 9 wire harness clamps to connect the wire harness.
Install the bolt.
Connect the wire harness to the rack and pinion power steering gear assembly with the 2 bolts.
Connect the rack and pinion power steering gear assembly connector.
Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.
for RHD:
Engage the 8 wire harness clamps to connect the wire harness.
Install the bolt.
Connect the wire harness to the rack and pinion power steering gear assembly with the bolt.
Connect the rack and pinion power steering gear assembly connector.
Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.
Engage the wire harness clamp and connect the vacuum switching valve (for active control engine mount system) connector.
Connect the park/neutral position switch assembly connector.
Connect the connector of the transmission wire connector and rotate the lever and engage the claw.
Rotate the lever until the claw of the transmission wire connector makes a click sound.
45319
20.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)
35104V
21.INSTALL BREATHER PLUG HOSE
Install the breather plug sub-assembly to the breather plug hose.
Install the breather plug hose to the No. 1 breather plug (ATM).
Engage the 2 hose clamps to connect the breather plug hose.
16260
22.CONNECT WATER BY-PASS HOSE ASSEMBLY
Connect the water by-pass hose assembly to the transmission oil cooler and slide the clip to secure it.
| *a | 2 to 7 mm (0.0787 to 0.276 in.) | *b | Paint Mark |
| *c | 45° (Claw of Clip Location) | - | - |
Make sure to slide the water by-pass hose assembly until it contacts the hose stopper of the transmission oil cooler.
Make sure to align the paint mark of the water by-pass hose assembly with the paint mark of the transmission oil cooler.
Make sure that the claws of the clip are within the location shown in the illustration.
16261G
23.INSTALL FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)
24.CONNECT VACUUM HOSE
Engage the 9 clamps to connect the vacuum hose to the automatic transaxle assembly.
Connect the vacuum hose to the vacuum hose connector.
Connect the vacuum hose to the rear engine mounting insulator.
32101A
25.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.
| *a | Adhesive |
Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.
Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.
11361J
26.INSTALL FLYWHEEL HOUSING UNDER COVER
27.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
28.CHECK AUTOMATIC TRANSAXLE SYSTEM
If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION