Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2021.02
RM33A0E _51 Engine / Hybrid System _098627 M20A-FKS ENGINE MECHANICAL _0463502 ENGINE UNIT A

M20A-FKS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E8 "TORX" socket wrench, install the stud bolt to the timing chain cover assembly.

A480787C01
5.25,0.385 5.563,0.542 0.313,0.156 10 false *a 5.26,1.479 5.573,1.635 0.313,0.156 10 false *b 5.906,0.844 6.219,1 0.313,0.156 10 false *c
*a 33.1 mm (1.30 in.) *b 15 mm (0.591 in.)
*c 95 mm (3.74 in.) - -


Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12262 3.INSTALL NO. 2 VENTILATION HOSE

a.

Install the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


Hide 25759A 4.INSTALL VACUUM SURGE TANK BRACKET

a.

Using an 8 mm socket wrench, install the vacuum surge tank bracket to the camshaft housing sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17169A 6.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the 2 bolts.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 16032 7.INSTALL ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

a.

Install the engine water pump assembly (water inlet housing) and a new gasket to the cylinder block sub-assembly with the 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16031 8.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 11452D 9.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250E 12.INSTALL DIRECT FUEL INJECTOR ASSEMBLY

Hide 23250F 14.INSTALL PORT FUEL INJECTOR ASSEMBLY

Hide 23291 16.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23807 18.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 82126A 19.INSTALL NO. 6 ENGINE WIRE

a.

Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 2 clamps.


c.

Connect the 4 connectors.


Hide 82219A 20.INSTALL SENSOR WIRE

a.

Install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 3 clamps.


c.

Connect the 4 connectors.


Hide 21.INSTALL NO. 1 WATER BY-PASS HOSE ASSEMBLY

a.

Install the No. 1 water by-pass hose assembly and slide the 2 clips to secure it.


b.

Install the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23100X 22.TEMPORARILY INSTALL FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 23801P 23.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 24.INSTALL FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 23801P 25.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A426800C01
2.74,2.76 2.844,2.594 false 2.896,2.49 3.208,2.646 0.313,0.156 10 false *a 1.604,2.406 1.917,2.563 0.313,0.156 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly (for high pressure) side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




c.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23910A 26.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Install the fuel tube sub-assembly to the fuel delivery pipe sub-assembly.


b.

Install the fuel pipe clamp to the fuel tube connector.


c.

Connect the fuel tube sub-assembly to the fuel pump assembly (for high pressure).


Hide 17177 27.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 17111 28.INSTALL INTAKE MANIFOLD

Hide 16279 30.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.


b.

Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25601 32.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 22271 34.INSTALL THROTTLE BODY GASKET

Hide 22030 35.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17141 36.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 17167 38.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 16575B 39.INSTALL WATER HOSE CLAMP BRACKET

a.

Install the water hose clamp bracket to the camshaft housing sub-assembly with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16260 40.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A465548

Install the flow shutting valve (water by-pass hose assembly) to the water hose clamp bracket with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 16207 41.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A465547

Install the No. 2 water by-pass pipe sub-assembly to the water hose clamp bracket with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the No. 2 water by-pass pipe sub-assembly to the water by-pass outlet sub-assembly and slide the clip to secure it.


Hide 16620D 42.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:
A409240

·

Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.

·

Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.



a.

Install the V-ribbed belt tensioner assembly to the No. 2 timing chain cover assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 88310 43.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

Hide 16361A 45.INSTALL V-RIBBED BELT

Hide 43457 46.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)