Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  Image from Camera for Panoramic View Monitor is Abnormal  


DESCRIPTION

The display signal from each camera is transmitted to the radio and display receiver assembly via the television camera controller.

WIRING DIAGRAM

E455627E06
0.344,8.031 2.542,8.594 2.198,0.563 10 false Television Camera Controller 2.75,7.802 5.042,8 2.292,0.198 10 false Rear Television Camera Assembly 2.74,7.635 3.198,7.833 0.458,0.198 10 false m4 2.677,4.969 3.135,5.167 0.458,0.198 10 false B7 2.677,5.125 4.969,5.323 2.292,0.198 10 false Front Television Camera Assembly 5.292,2.708 6.99,3.396 1.698,0.688 10 false Radio and Display Receiver Assembly 3.198,5.948 3.656,6.146 0.458,0.198 10 false CV- 3.208,6.542 3.667,6.74 0.458,0.198 10 false CV+ 3.208,7.135 3.667,7.333 0.458,0.198 10 false CGND 3.021,5.823 3.177,6.021 0.156,0.198 10 false 2 3.021,6.427 3.177,6.625 0.156,0.198 10 false 3 3.021,7.01 3.177,7.208 0.156,0.198 10 false 5 3.031,3.25 3.188,3.448 0.156,0.198 10 false 6 3.031,3.646 3.188,3.844 0.156,0.198 10 false 2 3.031,4.021 3.188,4.219 0.156,0.198 10 false 3 3.031,4.438 3.188,4.635 0.156,0.198 10 false 5 5.375,1.833 5.667,2.156 0.292,0.323 10 false 29 5.375,1.365 5.667,1.604 0.292,0.24 10 false 28 5.375,0.771 5.677,1 0.302,0.229 10 false 18 1.24,1.375 1.396,1.573 0.156,0.198 10 false 7 1.229,1.833 1.448,2.115 0.219,0.281 10 false 24 1.24,2.427 1.396,2.625 0.156,0.198 10 false 8 0.865,1.448 1.479,1.646 0.615,0.198 10 false NS+ 0.885,1.917 1.5,2.115 0.615,0.198 10 false NS- 0.833,2.521 1.448,2.719 0.615,0.198 10 false NSG 0.75,3.333 1.365,3.531 0.615,0.198 10 false BCB+ 0.781,3.729 1.396,3.927 0.615,0.198 10 false BCV- 0.75,4.135 1.365,4.333 0.615,0.198 10 false BCV+ 0.74,4.542 1.344,4.75 0.604,0.208 10 false BGND 0.74,4.958 1.344,5.167 0.604,0.208 10 false SGND 0.885,5.917 1.344,6.115 0.458,0.198 10 false CV- 0.854,6.521 1.313,6.719 0.458,0.198 10 false CV+ 0.76,7.115 1.219,7.313 0.458,0.198 10 false CGND 3.208,3.365 3.823,3.563 0.615,0.198 10 false BCB+ 3.198,3.75 3.813,3.948 0.615,0.198 10 false BCV- 3.198,4.115 3.813,4.313 0.615,0.198 10 false BCV+ 3.188,4.552 3.792,4.76 0.604,0.208 10 false BGND 1.219,3.25 1.49,3.469 0.271,0.219 10 false 15 1.219,3.646 1.49,3.865 0.271,0.219 10 false 13 1.229,4.031 1.5,4.25 0.271,0.219 10 false 36 1.229,4.438 1.5,4.656 0.271,0.219 10 false 37 1.229,4.833 1.5,5.052 0.271,0.219 10 false 14 1.229,5.823 1.542,6.083 0.313,0.26 10 false 30 1.229,6.417 1.5,6.656 0.271,0.24 10 false 29 1.229,7.01 1.604,7.302 0.375,0.292 10 false 32 5.635,1.469 6.25,1.667 0.615,0.198 10 false V+ 5.635,1.927 6.25,2.125 0.615,0.198 10 false V- 5.625,0.865 6.24,1.063 0.615,0.198 10 false CSW+ 2.135,4.74 2.292,4.938 0.156,0.198 10 false * 3.344,2.375 3.5,2.573 0.156,0.198 10 false * 0.729,0.865 1.344,1.063 0.615,0.198 10 false RSW+ 1.229,0.771 1.531,1 0.302,0.229 10 false 6 5.906,6.104 6.99,6.469 1.083,0.365 10 false from ACC Relay 4.552,6.26 5.313,6.646 0.76,0.385 10 false ECU-ACC 4.25,6.01 4.406,6.208 0.156,0.198 10 false 6 3.885,6.104 4.344,6.302 0.458,0.198 10 false CB+ 5.292,2.563 5.583,2.885 0.292,0.323 10 false K2 0.115,7.885 1.469,8.271 1.354,0.385 10 false R126 5.781,8.448 6.688,8.677 0.906,0.229 10 false *: Shielded 2.115,6.771 2.271,6.969 0.156,0.198 10 false *

E457470E03
0.052,6.021 2.448,6.458 2.396,0.438 10 false Television Camera Controller 3.302,5.99 3.625,6.188 0.323,0.198 10 false O22 3.302,2.927 3.625,3.125 0.323,0.198 10 false N24 3.302,3.104 5.802,3.51 2.5,0.406 10 false Outer Rear View Mirror Assembly RH 4.792,2.469 6.24,2.906 1.448,0.438 10 false Side Television Camera Assembly RH 0.896,0.719 1.396,0.917 0.5,0.198 10 false RCB+ 0.896,1.531 1.396,1.729 0.5,0.198 10 false RCV- 0.885,1.135 1.385,1.333 0.5,0.198 10 false RCV+ 0.865,1.927 1.365,2.125 0.5,0.198 10 false RGND 0.854,2.323 1.354,2.521 0.5,0.198 10 false SGND 0.906,3.74 1.406,3.938 0.5,0.198 10 false LCB+ 0.927,4.563 1.427,4.76 0.5,0.198 10 false LCV- 0.906,4.177 1.406,4.375 0.5,0.198 10 false LCV+ 0.875,4.958 1.375,5.156 0.5,0.198 10 false LGND 0.865,5.344 1.365,5.542 0.5,0.198 10 false SGND 3.323,0.625 3.823,0.823 0.5,0.198 10 false RCB+ 3.323,1.417 3.823,1.615 0.5,0.198 10 false RCV- 3.323,1.01 3.823,1.208 0.5,0.198 10 false RCV+ 3.333,1.802 3.833,2 0.5,0.198 10 false RGND 3.323,4.833 3.823,5.031 0.5,0.198 10 false LGND 3.323,3.667 3.823,3.865 0.5,0.198 10 false LCB+ 3.333,4.438 3.833,4.635 0.5,0.198 10 false LCV- 3.323,4.042 3.823,4.24 0.5,0.198 10 false LCV+ 3.146,0.625 3.406,0.833 0.26,0.208 10 false 2 3.156,1.021 3.417,1.281 0.26,0.26 10 false 1 3.083,1.417 3.458,1.615 0.375,0.198 10 false 12 3.083,1.813 3.469,2.052 0.385,0.24 10 false 13 1.365,0.594 1.656,0.792 0.292,0.198 10 false 40 1.354,1.417 1.677,1.646 0.323,0.229 10 false 16 1.354,1.01 1.594,1.208 0.24,0.198 10 false 38 1.354,1.813 1.646,2.031 0.292,0.219 10 false 17 1.354,2.219 1.615,2.427 0.26,0.208 10 false 39 1.365,3.656 1.625,3.865 0.26,0.208 10 false 12 1.365,4.458 1.625,4.667 0.26,0.208 10 false 34 1.365,4.052 1.625,4.26 0.26,0.208 10 false 10 1.365,4.844 1.625,5.052 0.26,0.208 10 false 35 1.354,5.25 1.615,5.458 0.26,0.208 10 false 11 2.281,2.104 2.479,2.333 0.198,0.229 10 false * 2.271,5.135 2.5,5.458 0.229,0.323 10 false * 0.292,6.448 1.5,6.719 1.208,0.271 10 false *: Shielded 4.792,5.5 6.24,5.938 1.448,0.438 10 false Side Television Camera Assembly LH 3.302,6.156 5.802,6.563 2.5,0.406 10 false Outer Rear View Mirror Assembly LH 4.885,3.76 5.385,3.958 0.5,0.198 10 false LCB+ 4.698,3.667 4.854,3.865 0.156,0.198 10 false 1 4.698,4.458 4.854,4.656 0.156,0.198 10 false 7 4.698,4.042 4.854,4.24 0.156,0.198 10 false 5 4.708,4.854 4.865,5.052 0.156,0.198 10 false 3 4.885,4.167 5.385,4.365 0.5,0.198 10 false LCV+ 4.875,4.563 5.375,4.76 0.5,0.198 10 false LCV- 4.885,4.927 5.385,5.125 0.5,0.198 10 false LGND 4.885,0.719 5.385,0.917 0.5,0.198 10 false RCB+ 4.885,1.125 5.385,1.323 0.5,0.198 10 false RCV+ 4.875,1.542 5.375,1.74 0.5,0.198 10 false RCV- 4.885,1.917 5.385,2.115 0.5,0.198 10 false RGND 4.688,0.615 4.844,0.813 0.156,0.198 10 false 1 4.688,1.01 4.844,1.208 0.156,0.198 10 false 5 4.698,1.406 4.854,1.604 0.156,0.198 10 false 7 4.698,1.792 4.854,1.99 0.156,0.198 10 false 3 0.042,5.854 1.5,6.219 1.458,0.365 10 false R126 4.542,5.5 4.927,5.865 0.385,0.365 10 false A 4.51,2.469 4.896,2.833 0.385,0.365 10 false B 3.156,3.667 3.417,3.875 0.26,0.208 10 false 2 3.167,4.042 3.427,4.302 0.26,0.26 10 false 1 3.083,4.458 3.458,4.656 0.375,0.198 10 false 12 3.073,4.875 3.458,5.115 0.385,0.24 10 false 13 3.344,2.208 3.844,2.406 0.5,0.198 10 false SGND 3.083,2.219 3.469,2.458 0.385,0.24 10 false 14 3.073,5.25 3.458,5.49 0.385,0.24 10 false 14 3.333,5.25 3.833,5.448 0.5,0.198 10 false SGND

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



HINT:
Images may be unclear even in normal conditions if:
·

Electrical devices are used in the cabin (noise may occur in the image).

·

The camera lens is frosted over (the image immediately after turning the ignition switch ON may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night, etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The television camera assembly lens is scratched.

·

The television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK PANORAMIC VIEW MONITOR SYSTEM
a.

Check if the same malfunction occurs when the panoramic view monitor screen is displayed.


Result:
Result Proceed to
Rear view screen is not displayed. A
Front view screen is not displayed. B
Side monitor screen (LH side) is not displayed. C
Side monitor screen (RH side) is not displayed. D
Panoramic view monitor screen is not displayed. E



A

2.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - REAR TELEVISION CAMERA ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - FRONT TELEVISION CAMERA ASSEMBLY)

C

10.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY LH)

D

16.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY RH)

E

22.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - REAR TELEVISION CAMERA ASSEMBLY)

OK

3.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)

OK

4.CHECK TELEVISION CAMERA CONTROLLER (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TELEVISION CAMERA CONTROLLER (CV-, CGND)

OK

5.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

5.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

OK

NG

6.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - FRONT TELEVISION CAMERA ASSEMBLY)

OK

7.CHECK TELEVISION CAMERA CONTROLLER (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TELEVISION CAMERA CONTROLLER (BCV-, BGND)

NG

8.CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)

OK

8.CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)

OK

9.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

NG

9.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

OK

NG

10.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY LH)

OK

11.CHECK TELEVISION CAMERA CONTROLLER (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TELEVISION CAMERA CONTROLLER (LCV-, LGND)

OK

12.CHECK TELEVISION CAMERA CONTROLLER (LCB+, LGND)

NG

12.CHECK TELEVISION CAMERA CONTROLLER (LCB+, LGND)

OK

13.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

NG

13.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH (LCV+, LGND)

OK

NG

14.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
14.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

OK

15.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

15.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

16.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY RH)

OK

17.CHECK TELEVISION CAMERA CONTROLLER (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK TELEVISION CAMERA CONTROLLER (RCV-, RGND)

OK

18.CHECK TELEVISION CAMERA CONTROLLER (RCB+, RGND)

NG

18.CHECK TELEVISION CAMERA CONTROLLER (RCB+, RGND)

OK

19.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

NG

19.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

OK

NG

20.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
20.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

OK

21.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

21.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG

22.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the R126 television camera controller.


b.

Disconnect the K2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R126-7 (NS+) - K2-28 (V+) Always Below 1 Ω
R126-24 (NS-) - K2-29 (V-) Always Below 1 Ω
R126-6 (RSW+) - K2-18 (CSW+) Always Below 1 Ω
R126-8 (NSG) - Body ground Always 10 kΩ or higher
R126-7 (NS+) or K2-28 (V+) - Body ground Always 10 kΩ or higher
R126-24 (NS-) or K2-29 (V-) - Body ground Always 10 kΩ or higher
R126-6 (RSW+) or K2-18 (CSW+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Replace the radio and display receiver assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (RADIO AND DISPLAY RECEIVER ASSEMBLY WAS DEFECTIVE)

NG