Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2021.02
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327371 ENGINE UNIT A

2GR-FKS ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of engine assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly (for port injection)

·

Replacement of fuel injector assembly (for direct injection)

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

PROCEDURE

Hide 89615 1.REMOVE KNOCK CONTROL SENSOR

Hide 82219A 2.REMOVE SENSOR WIRE

a.
A373763

Disengage the 2 clamps and remove the bolt and sensor wire.


Hide 29300 4.REMOVE VACUUM PUMP ASSEMBLY

Hide 16267 5.REMOVE NO. 3 WATER BY-PASS HOSE

a.
A408771

Slide the clip and remove the No. 3 water by-pass hose from the water inlet pipe.


Hide 16264 6.REMOVE NO. 2 WATER BY-PASS HOSE

a.
A408772

Slide the clip and remove the No. 2 water by-pass hose from the water outlet.


Hide 12261 7.REMOVE VENTILATION HOSE

a.
A373764

Slide the clip and remove the ventilation hose from the PCV valve (ventilation valve sub-assembly).


Hide 12262 8.REMOVE NO. 2 VENTILATION HOSE

a.
A373570

Slide the clip and remove the No. 2 ventilation hose from the cylinder head cover sub-assembly.


Hide 16361A 9.REMOVE V-RIBBED BELT

Hide 27020 10.REMOVE GENERATOR ASSEMBLY

Hide 11.REMOVE COMPRESSOR ASSEMBLY WITH MAGNETIC CLUTCH

Hide 88431 12.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A408030

Remove the 2 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly.


Hide 16604 13.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 14.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A408556

Remove the 2 bolts and V-ribbed belt tensioner assembly.


Hide 16173 15.REMOVE WATER PUMP PULLEY

Hide 11452 16.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick from the engine oil level dipstick guide.


b.
A408031

Remove the bolt and engine oil level dipstick guide from the camshaft housing sub-assembly LH and oil pan sub-assembly.


c.
A408032

Remove the engine oil level dipstick guide O-ring from the engine oil level dipstick guide.


Hide 12585 17.REMOVE NO. 5 CYLINDER BLOCK INSULATOR (w/ Oil Cooler)

a.
A373571

Remove the No. 5 cylinder block insulator from the engine assembly.


Hide 43457 18.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A400025

Remove the 3 bolts and drive shaft bearing bracket from the cylinder block sub-assembly.


Hide 19.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A408399

Remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly LH.


b.
A408397

Remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly.


Hide 16522 20.REMOVE WATER FILLER BRACKET

a.
A408398

Remove the 2 bolts and water filler bracket from the camshaft housing sub-assembly LH.


Hide 12631A 21.REMOVE ENGINE COVER BRACKET

a.
A408028

Remove the bolt and engine cover bracket from the cylinder head cover sub-assembly LH.