Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY (for NICKEL METAL HYDRIDE BATTERY)
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0328989 HV BATTERY(for NICKEL METAL HYDRIDE BATTERY) A

HYBRID / BATTERY CONTROL  HV BATTERY(for NICKEL METAL HYDRIDE BATTERY)  INSTALLATION  


PROCEDURE

Hide G92DH 1.INSPECT NO. 1 HV BATTERY INTAKE FILTER

Hide G92E1A 2.INSTALL NO. 1 HV BATTERY INTAKE DUCT LH

Hide G920R 3.INSTALL NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide G92Z2 5.INSTALL HYBRID BATTERY TERMINAL BLOCK

Hide G92Q1 7.INSTALL NO. 1 HV BATTERY SHIELD PANEL

Hide G920NB 8.INSTALL UPPER HV BATTERY COVER SUB-ASSEMBLY

Hide G920G 9.TEMPORARILY INSTALL NO. 4 HV BATTERY END PLATE SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.

Temporarily install the No. 4 HV battery end plate sub-assembly to the HV battery with the 2 bolts and 2 nuts.


b.

Fully tighten the 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide G920K 10.INSTALL NO. 5 HV BATTERY END PLATE SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.

Install the No. 5 HV battery end plate sub-assembly to the HV battery with the 12 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide G920TA 11.INSTALL NO. 4 HV BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.

Install the No. 4 HV battery shield sub-assembly to the HV battery with the 4 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide G920SA 12.INSTALL NO. 3 HV BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.

Install the No. 3 HV battery shield sub-assembly to the HV battery with the 4 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide G920G 13.INSTALL NO. 4 HV BATTERY END PLATE SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.

Fully tighten the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide G9510 14.INSTALL HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A406080C01
0.229,1.729 0.427,1.917 0.198,0.188 10 true *a 1.042,0.156 1.219,0.323 0.177,0.167 10 true *b 3.031,1.552 3.219,1.75 0.188,0.198 10 true *c 1.906,0.125 2.104,0.313 0.198,0.188 10 true *a 2.719,0.135 2.917,0.323 0.198,0.188 10 true *a
*a Bolt (A)
(Bolt Length: 25 mm (0.984 in.))
*b Bolt (B)
(Bolt Length: 24 mm (0.945 in.))
*c Bolt (C)
(Bolt Length: 65 mm (2.559 in.))


Install the HV battery to the vehicle body with the 3 bolts (A), bolt (B) and bolt (C).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.

·

As bolts with 3 different lengths are used, make sure to install each bolt to the correct position.

·

If the HV battery has been struck or dropped, replace it.




Hide 82161 15.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the battery voltage sensor connector.


b.

Engage the clamp.


Hide G92F1 16.INSTALL NO. 1 HYBRID BATTERY EXHAUST DUCT

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the claw to install the No. 1 hybrid battery exhaust duct to the HV battery.


b.

Install the clip.


Hide 82161 17.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the 2 clamps.


Hide 899A0 18.INSTALL NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Hide 82161 19.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the HV battery junction block assembly connector.


b.

Connect the electric vehicle battery plug assembly connector.


c.

Engage the clamp.


Hide 821H1 20.CONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the floor wire connector.


b.
A406074C01
1.875,1.25 2.396,1.25 true 2.396,1.146 2.594,1.344 0.198,0.198 10 true *a
*a Shield Ground


Connect the shield ground to the HV battery.


c.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 21.INSTALL NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Be sure to wear insulated gloves.


a.
A408494C01
1.365,1.177 1.646,1.177 false 1.198,0.99 1.26,0.813 1.26,0.813 1.406,0.813 true 1.677,1.094 1.99,1.25 0.313,0.156 10 false *1 1.427,0.719 1.74,0.875 0.313,0.156 10 false *a 1.115,0.167 1.427,0.323 0.313,0.156 10 false *b
*1 Battery Cover Lock Striker
*a Button
*b Push


Install the No. 1 HV battery cover panel RH to the HV battery with the 3 bolts and 3 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Install the battery cover lock striker, then push the button to lock it.


Hide G9230 22.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 24.PERFORM INITIALIZATION