The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3. DISCHARGE FUEL SYSTEM PRESSURE
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.SECURE STEERING WHEEL
6.REMOVE FRONT WHEELS
53851M
7.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Remove the 3 screws and front wheel opening extension pad RH.
53852K
8.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Remove the 3 screws and front wheel opening extension pad LH.
51441
9.REMOVE NO. 1 ENGINE UNDER COVER
Remove the bolt, 2 clips, 6 screws and No. 1 engine under cover.
10.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)
Remove the 4 screws, 6 clips and No. 2 engine under cover assembly.
53737B
11.REMOVE FRONT FENDER APRON SEAL LH
Remove the 2 screws, clip and front fender apron seal LH.
53736
12.REMOVE FRONT FENDER APRON SEAL RH
Remove the 2 screws, clip and front fender apron seal RH.
13.REMOVE HEADLIGHT ASSEMBLY
for LED Type Turn Signal Light:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>REMOVAL
for Bulb Type Turn Signal Light:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
52618
14.REMOVE FRONT LOWER BUMPER ABSORBER
Remove the 4 bolts.
Disengage the 2 claws to remove the front lower bumper absorber.
15.DRAIN ENGINE COOLANT (for Engine)
16.DRAIN ENGINE OIL
17.DRAIN HYBRID TRANSAXLE FLUID
12601B
18.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Lift the front of the No. 1 engine cover sub-assembly to disengage the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to disengage the clip and remove the No. 1 engine cover sub-assembly.
Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.
G9200
19.REMOVE INVERTER WITH CONVERTER ASSEMBLY
G92A0A
20.REMOVE INVERTER RESERVE TANK ASSEMBLY
| *1 | No. 5 Inverter Cooling Hose |
| *2 | No. 2 Inverter Cooling Hose |
| *a | Pin |
| *b | Grommet |
Remove the bolt.
Disengage the pin and remove the inverter reserve tank assembly.
Slide the clip and disconnect the No. 5 inverter cooling hose from the inverter reserve tank assembly.
Slide the clip and disconnect the No. 2 inverter cooling hose from the inverter reserve tank assembly.
23826
21.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve assembly.
87246
22.DISCONNECT OUTLET HEATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the outlet heater hose from the No. 2 water by-pass pipe sub-assembly.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater hose connector with plastic bags to prevent damage and contamination.
87245
23.DISCONNECT INLET HEATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the inlet heater hose from the flow shutting valve (water by-pass hose assembly).
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater hose connector with plastic bags to prevent damage and contamination.
23901
24.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
89422
25.REMOVE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR (w/ Canister Pump Module)
16571C
26.DISCONNECT NO. 1 RADIATOR HOSE (w/o Canister Pump Module)
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
16571C
27.DISCONNECT NO. 1 RADIATOR HOSE (w/ Canister Pump Module)
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
Remove the bolt to disconnect the No. 1 radiator hose from the front engine mounting bracket.
16572D
28.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the water inlet.
88711
29.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY
88704
30.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
G9229A
31.DISCONNECT NO. 5 INVERTER COOLING HOSE
Slide the clip and disconnect the No. 5 inverter cooling hose from the motor cooling cooler.
32.DISCONNECT WIRE HARNESS
After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.
Remove the No. 2 relay block cover from the engine room relay block and junction block assembly.
Remove the nut from the engine room relay block and junction block assembly.
Disconnect the 5 connectors from the engine room relay block and junction block assembly.
Using a screwdriver, disengage the claw and disconnect the wire harness from the engine room relay block and junction block assembly.
Remove the 2 bolts and disengage the earth wire.
16281F
33.DISCONNECT NO. 5 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.
45220
34.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
17410
35.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
36.REMOVE FRONT DRIVE SHAFT ASSEMBLY
37.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
Remove the 6 bolts and body mounting plate.
Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the 3 bolts and the engine mounting stay LH from the engine mounting insulator sub-assembly LH.
Remove the 4 bolts and separate the engine mounting insulator sub-assembly LH from the hybrid vehicle transaxle assembly.
|
Bolt |
|
Nut |
Remove the 4 bolts (A), 2 bolts (B) and 2 bolts (C) and front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.
Remove the 2 bolts (D), 2 bolts (E) and 2 nuts and front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH from the front frame assembly and vehicle body.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
23825
38.REMOVE FUEL DELIVERY GUARD
Remove the bolt and fuel delivery guard from the engine mounting bracket RH.
39.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
11361J
40.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the flywheel housing under cover from the cylinder block sub-assembly.
45319
41.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)
82121
42.REMOVE ENGINE WIRE
Remove the engine wire from the engine assembly.
51100G
43.REMOVE FRONT FRAME ASSEMBLY
12361A
44.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>REMOVAL
12371A
45.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.
821H2
46.REMOVE HV AIR CONDITIONING WIRE
Disengage the 2 clamps.
| *a | Green-colored Lock |
|
Slide |
Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.
Make sure to wear insulated gloves.
Insulate the disconnected terminals and connector with insulating tape.
Remove the bolt.
Disengage the guide to remove the HV air conditioning wire from the hybrid vehicle transaxle assembly.
28193
47.REMOVE STARTER HOLE INSULATOR
11363A
48.REMOVE FLYWHEEL HOUSING SIDE COVER
30900
49.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
31270
50.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY
13405
51.REMOVE FLYWHEEL SUB-ASSEMBLY
19315
52.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
53.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine assembly to an engine stand.
54.REMOVE ENGINE HANGERS
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.
12305
55.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Disengage the No. 6 water by-pass hose.
Remove the bolt, nut and the radiator reserve tank assembly.
Disengage the clamp.
Remove the bolt and disconnect the cooler bracket from the engine mounting insulator sub-assembly RH.
Remove the 2 bolts and nut and remove the engine mounting insulator sub-assembly RH.
12341
56.REMOVE ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Remove the 2 bolts and engine mounting spacer from the vehicle body.
12306
57.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.
Remove the 2 bolts, nut and the engine mounting insulator sub-assembly LH.