Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER › from 2021.02
RM33C0E _52 Drivetrain _065436 AXLE AND DIFFERENTIAL _0331919 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42305 1.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

a.

Temporarily install the rear axle carrier sub-assembly to the rear shock absorber assembly with the nut and plate washer.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



b.
C370186

Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




c.

Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
135 N*m (1377 kgf*cm, 100 ft.*lbf)


Hide 2.INSTALL REAR FLEXIBLE HOSE BRACKET

a.

Install the rear flexible hose bracket to the rear axle carrier sub-assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48720A 3.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 48258C 4.INSTALL REAR LOWER COIL SPRING INSULATOR

Hide 48231B 5.INSTALL REAR COIL SPRING

Hide 48790 7.INSTALL REAR UPPER CONTROL ARM ASSEMBLY

a.

Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48720A 8.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 48740F 9.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48540 10.INSTALL REAR SHOCK ABSORBER ASSEMBLY

Hide 48840A 11.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 42450B 12.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Hide 42431 13.INSTALL REAR DISC

Hide 14.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Hide 47319F 15.INSTALL REAR FLEXIBLE HOSE

a.

Install the rear flexible hose to the rear flexible hose bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 890C0A 16.INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the nut.

Torque:
15.5 N*m (158 kgf*cm, 11 ft.*lbf)


b.

Engage the 2 clamps.


c.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


d.

Connect the No. 2 parking brake wire assembly connector to the rear axle hub and bearing assembly.


Hide 89408C 17.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 18.INSTALL REAR WHEEL

Hide 48740F 19.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 20.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>INSTALLATION


c.

Turn the power switch on (READY).


d.

Depress the brake pedal and release it.



Hide 21.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 23.PERFORM INITIALIZATION

Parking Support Brake System (Click here)
Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)for Initialization
(Click here)for Calibration
Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)