Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0093  Fuel System Leak Detected - Large Leak  


DESCRIPTION

Refer to DTC P0087 (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>P0087).

Refer to DTC P0088 (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>P0088).

DTC No. DTC Detection Condition Trouble Area
P0093 DTC is output when following conditions (a), (b) and (c) are all met and if difference of common rail pressure that fuel pressure sensor detects before and after fuel injection varies greatly from difference of value that ECM calculates before and after fuel injection, ECM determines that there may be fuel leaks.
(1 trip detection logic)
(a) Engine speed is 1500 rpm or higher.
(b) Fuel pressure sensor is normal (P0190, P0192, and P0193 are not detected).
(c) Suction control valve is normal (P0088, P0627 and P1229 are not detected).
·

Fuel leak (injection or supply pup assembly to common rail assembly to injector assembly)

·

Injector assembly

·

Injection or supply pump assembly (suction control valve)

·

Wire harness or connector

·

Common rail assembly

·

ECM



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pup assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs.


Result:
Result Proceed to
DTC P0087, P0190, P0192, P0193, P0200, P0088, P0627 or P1229 is not output A
DTC P0087, P0190, P0192, P0193, P0200, P0088, P0627 or P1229 is output B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
HINT:

By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.

HINT:

There may be fuel leaks inside the components, such as the injection or supply pump assembly.


OK:

No leak.



Result:
Proceed to
OK
NG



OK

3.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

REPAIR OR REPLACE FUEL LEAK POINT

3.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.
A153586E12
1.021,0.365 1.5,0.656 true 0.073,0.063 0.396,0.26 0.323,0.198 10 false *a 0.792,0.219 1.021,0.417 0.229,0.198 10 false *1

Disconnect the suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 1.9 to 2.3 Ω


Text in Illustration
*1 Suction Control Valve
*a Component without harness connected
(Injection or Supply Pump Assembly)


Result:
Proceed to
OK
NG



OK

4.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

4.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Disconnect the suction control valve connector and then start the engine.

OK:

Engine does not start.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

5.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
Engine Speed Result
Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

6.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Check that the internal fuel pressure of the common rail is within the specification below.

Standard:
Engine Speed Fuel Press
Idling Approximately 25000 to 35000 kPa



Result:
Result Proceed to
NG A
OK B



A

7.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)

B

11.CHECK HARNESS AND CONNECTOR (ECM - SUCTION CONTROL VALVE)
7.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Standard Resistance Condition Specified Condition
B59-26 (PCR1) - B92-2 (PCR1) Always Below 1 Ω
B59-18 (VC) - B92-3 (VC1) Always Below 1 Ω
B59-28 (E2) - B92-1 (E1) Always Below 1 Ω
B59-26 (PCR1) or B92-2 (PCR1) - Body ground Always 10 kΩ or higher
B59-18 (VC) or B92-3 (VC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Wiggle the fuel pressure sensor connector and check that the fuel pressure reading does not change.

OK:

The fuel pressure reading does not change.



Result:
Proceed to
OK
NG



OK

9.PERFORM INITIALIZATION (INJECTION OR SUPPLY PUMP ASSEMBLY)

NG

REPLACE COMMON RAIL ASSEMBLY

9.PERFORM INITIALIZATION (INJECTION OR SUPPLY PUMP ASSEMBLY)

Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)

b.

Start the engine and warm it up.


c.

Drive the vehicle by 1500 rpm or more for 5 minutes.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.


Result:
Result Proceed to
No DTC output A
DTC P0093 B



A

END

B

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (ECM - SUCTION CONTROL VALVE)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Standard Resistance Condition Specified Condition
B59-2 (PCV+) - B52-1 (SCV+) Always Below 1 Ω
B59-1 (PCV-) - B52-2 (SCV-) Always Below 1 Ω
B59-2 (PCV+) or B52-1 (SCV+) - Body ground Always 10 kΩ or higher
B59-1 (PCV-) or B52-2 (SCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT ECM (PCR1 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT ECM (PCR1 VOLTAGE)
a.
A224395E25
0.51,0.198 0.938,0.448 0.427,0.25 0.323,1.531 0.563,0.958 true 1.229,1.542 1,1.031 true 0.094,0.083 0.323,0.292 0.229,0.208 10 false *a 0.604,0.25 0.906,0.427 0.302,0.177 10 false B59 0.094,1.573 0.833,1.792 0.74,0.219 10 false 26 (PCR1) 1.094,1.573 1.635,1.802 0.542,0.229 10 false 28 (E2)

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B59-26 (PCR1) - B59-28 (E2) Idling 1.3 to 1.7 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

REPLACE COMMON RAIL ASSEMBLY