Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) for more than 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 When conditions (a), (b) and (c) are met, positive (+B) battery voltage of 10.5 V or more is applied to ECM for 20 seconds:
(1 trip detection logic)
(a) Vehicle speed is more than 20 km/h (12.4 mph)
(b) Engine speed is more than 1000 rpm
(c) STA signal is ON
·

Starter relay circuit

·

Ignition switch

·

Park/neutral position switch

·

ECM



WIRING DIAGRAM

A403473E01
1.198,0.948 1.656,1.146 0.458,0.198 10 false AM2 3.625,0.938 4.25,1.125 0.625,0.188 10 false ST NO. 2 1.875,1.875 2.5,2.063 0.625,0.188 10 false ST NO. 1 0.729,3.052 1.354,3.24 0.625,0.188 10 false FL MAIN 2.76,4.375 3.24,4.583 0.479,0.208 10 false Starter 1.344,4.302 1.854,4.5 0.51,0.198 10 false Battery 6.125,0.771 6.458,0.969 0.333,0.198 10 false STA 4.688,2.26 4.938,2.438 0.25,0.177 10 false ST 6.333,4.708 6.656,4.906 0.323,0.198 10 false B60 6.344,4.875 6.74,5.073 0.396,0.198 10 false ECM 3.021,3.594 3.271,3.771 0.25,0.177 10 false ST 2.74,3.656 2.885,3.844 0.146,0.188 10 false B 2.396,3.667 2.698,3.865 0.302,0.198 10 false C11 2.958,3.385 3.26,3.583 0.302,0.198 10 false B99 2.469,3.479 2.615,3.667 0.146,0.188 10 false 1 2.927,3.167 3.073,3.354 0.146,0.188 10 false 1 4.448,1.781 4.594,1.969 0.146,0.188 10 false 1 4.458,2.729 4.604,2.917 0.146,0.188 10 false 2 4.01,1.792 4.156,1.979 0.146,0.188 10 false 5 4.01,2.729 4.156,2.917 0.146,0.188 10 false 3 5.833,0.667 6.042,0.865 0.208,0.198 10 false 18 3.219,0.677 3.365,0.865 0.146,0.188 10 false 9 1.823,0.667 2.031,0.865 0.208,0.198 10 false 12 2.125,0.677 2.542,0.875 0.417,0.198 10 false AM2 2.844,0.677 3.177,0.865 0.333,0.188 10 false ST2 1.813,1.094 2.125,1.281 0.313,0.188 10 false J63 1.823,1.26 3.469,1.469 1.646,0.208 10 false Ignition Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the tester when the ignition switch is turned to ON and START.

OK:
Ignition Switch Condition Starter Signal
ON OFF
START ON



Result:
Result Proceed to
NG (for manual transmission) A
NG (for automatic transmission) B
OK C



A

2.INSPECT IGNITION SWITCH ASSEMBLY

B

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

2.INSPECT IGNITION SWITCH ASSEMBLY
a.
A403398E01
1.083,1.74 1.635,1.313 true 2.521,1.719 2.177,1.313 true 0.823,1.74 1.135,1.938 0.313,0.198 10 false ST2 2.563,1.719 2.875,1.917 0.313,0.198 10 false AM2 0.708,2.427 1.156,2.625 0.448,0.198 10 false LOCK 2.458,2.875 2.969,3.073 0.51,0.198 10 false START 2.271,2.365 2.563,2.542 0.292,0.177 10 false ON 1.573,2.021 1.927,2.198 0.354,0.177 10 false ACC 0.167,0.156 0.479,0.354 0.313,0.198 10 false *1

Disconnect the ignition switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
All terminals LOCK 10 kΩ or higher
12 (AM2) - 9 (ST2) START Below 1 Ω


Text in Illustration
*1 Component without harness connected
(Ignition Switch)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY, IGNITION SWITCH)

NG

REPLACE IGNITION SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY, IGNITION SWITCH)
a.

Remove the starter relay.


b.

Disconnect the ignition switch connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 or B60-18 (STA) - Body ground Always 10 kΩ or higher
J63-9 (ST2) or B60-18 (STA) - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the ignition switch connector.


g.

Reinstall the starter relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY, PARK/NEUTRAL POSITION SWITCH)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY, PARK/NEUTRAL POSITION SWITCH)
a.

Remove the starter relay.


b.

Disconnect the park/neutral position switch connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 or B60-18 (STA) - Body ground Always 10 kΩ or higher
J63-9 (ST2) or B60-18 (STA) - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the park/neutral position switch connector.


g.

Reinstall the starter relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR