Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P2031  Exhaust Gas Temperature Sensor Circuit (Bank 1 Sensor 2)  P2032  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)  P2033  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2)  


DESCRIPTION

Refer to DTC P0544 (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>P0544).

DTC No. DTC Detection Condition Trouble Area
P2031 All of the following conditions are met:
(1 trip detection logic)
(a) Engine has been running for 30 minutes or more.
(b) Engine coolant temperature is 70°C (158°F) or higher.
(c) Injection volume is 40 mm3/st or more.
(d) Sensor 2 output is less than 0.2 V or more than 4.95 V for 8 seconds or more.
·

Open or short in exhaust gas temperature sensor (bank 1 sensor 2) circuit

·

Exhaust gas temperature sensor (bank 1 sensor 2)

·

ECM


P2032 All of the following conditions are met:
(1 trip detection logic)
(a) Engine has been running for 30 minutes or more.
(b) Engine coolant temperature is 70°C (158°F) or higher.
(c) Injection volume is 40 mm3/st or more.
(d) Sensor 2 output is less than 0.2 V for 8 seconds or more.
·

Open or short in exhaust gas temperature sensor (bank 1 sensor 2) circuit

·

Exhaust gas temperature sensor (bank 1 sensor 2)

·

ECM


P2033 All of the following conditions are met:
(1 trip detection logic)
(a) Engine has been running for 30 minutes or more.
(b) Engine coolant temperature is 70°C (158°F) or higher.
(c) Injection volume is 40 mm3/st or more.
(d) Sensor 2 output is more than 4.95 V for 8 seconds or more.
·

Open or short in exhaust gas temperature sensor (bank 1 sensor 2) circuit

·

Exhaust gas temperature sensor (bank 1 sensor 2)

·

ECM



HINT:
·

Sensor 1 represents a sensor located upstream on the DPF catalytic converter.

·

Sensor 2 represents a sensor located downstream on the DPF catalytic converter.

·

After confirming DTC P2031, P2032, and P2033, check the upstream and downstream exhaust gas temperature by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.

Result
Condition Exhaust Gas Temperature Exhaust Gas Temperature Sensor Condition
Idling after warm-up Constant at 50 to 700°C (122 to 1292°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit



WIRING DIAGRAM

A199002E43
5.208,1.573 5.448,1.74 0.24,0.167 10 false 28 5.167,1.771 5.458,1.969 0.292,0.198 10 false B59 5.25,0.948 5.396,1.125 0.146,0.177 10 false 1 2.146,1.646 2.375,1.844 0.229,0.198 10 false E2 1.948,1.042 2.385,1.229 0.438,0.188 10 false THCO 5.521,1.656 5.833,1.823 0.313,0.167 10 false E2 5.51,1.063 5.917,1.229 0.406,0.167 10 false THCO 5.167,1.156 5.479,1.344 0.313,0.188 10 false B60 0.604,2.333 0.927,2.521 0.323,0.188 10 false A45 2.427,1.646 2.573,1.833 0.146,0.188 10 false 2 2.427,1.031 2.573,1.229 0.146,0.198 10 false 1 5.99,2.719 6.427,2.906 0.438,0.188 10 false ECM 0.594,2.51 2.698,2.875 2.104,0.365 10 false Exhaust Gas Temperature Sensor (Bank 1 Sensor 2) 6.188,0.688 6.458,0.875 0.271,0.188 10 false 5 V 6.146,0.938 6.323,1.115 0.177,0.177 10 false R

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (EXHAUST GAS TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


e.

Read the value.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Result Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) B
Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining the engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C


HINT:
·

If there is a open circuit, the intelligent tester will indicate 0°C (32°F).

·

If there is an short circuit, the intelligent tester will indicate 1000°C (1832°F).





A

2.READ VALUE USING INTELLIGENT TESTER (OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (OPEN IN WIRE HARNESS)
a.
A227219E04
0.698,3.594 1.104,3.844 0.406,0.25 0.771,3.646 1.094,3.833 0.323,0.188 10 false A45 2.344,1 2.771,1.177 0.427,0.177 10 false THCO 2.344,1.333 2.615,1.531 0.271,0.198 10 false E2 0.646,0.479 0.844,0.667 0.198,0.188 10 false *1 1.708,3.135 1.875,3.302 0.167,0.167 10 false *3 2.594,1.771 2.823,1.979 0.229,0.208 10 false *2

Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


b.

Connect terminals 1 and 2 of the exhaust gas temperature sensor wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


g.

Read the value.

Standard:

1000°C (1832°F)


Text in Illustration
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 2)
*2 ECM
*3 Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (bank 1 sensor 2))


h.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE EXHAUST GAS TEMPERATURE SENSOR (BANK 1 SENSOR 2)

NG

3.READ VALUE USING INTELLIGENT TESTER (OPEN IN ECM)
3.READ VALUE USING INTELLIGENT TESTER (OPEN IN ECM)
a.
A427721E02
0.563,2.604 0.958,2.833 0.396,0.229 1.229,2.604 1.625,2.833 0.396,0.229 0.875,3.906 0.99,3.458 true 1.865,3.938 1.698,3.208 true 0.719,0.375 1.031,0.573 0.313,0.198 10 false *1 2.646,0.344 2.958,0.542 0.313,0.198 10 false *2 2.438,1.177 2.875,1.344 0.438,0.167 10 false THCO 2.417,1.531 2.677,1.708 0.26,0.177 10 false E2 0.635,2.646 0.948,2.844 0.313,0.198 10 false B59 1.323,2.635 1.635,2.833 0.313,0.198 10 false B60 0.719,3.948 1.031,4.146 0.313,0.198 10 false E2 1.667,3.948 2.094,4.146 0.427,0.198 10 false THCO 0.333,2.177 0.646,2.375 0.313,0.198 10 false *3

Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


b.

Connect terminals THCO and E2 of the ECM connectors.

HINT:

Before checking, do a visual and contact pressure check on the ECM connector.



c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


g.

Read the value.

Standard:

1000°C (1832°F)


Text in Illustration
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 2)
*2 ECM
*3 Component with harness connected
(ECM)


h.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EXHAUST GAS TEMPERATURE SENSOR)

NG

4.READ VALUE USING INTELLIGENT TESTER (SHORT IN WIRE HARNESS)
a.
A083863E72
0.781,0.333 1.01,0.521 0.229,0.188 10 false *1 2.417,1.031 2.865,1.208 0.448,0.177 10 false THCO 2.677,0.198 2.875,0.396 0.198,0.198 10 false *2 2.417,1.385 2.667,1.573 0.25,0.188 10 false E2

Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


f.

Read the value.

Standard:

0°C (32°F)


Text in Illustration
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 2)
*2 ECM


g.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE EXHAUST GAS TEMPERATURE SENSOR (BANK 1 SENSOR 2)

NG

5.READ VALUE USING INTELLIGENT TESTER (SHORT IN ECM)
5.READ VALUE USING INTELLIGENT TESTER (SHORT IN ECM)
a.
A116781E12
1.25,2.958 1.646,3.198 0.396,0.24 1.75,3.885 2.021,4.229 true 0.708,0.417 0.875,0.625 0.167,0.208 10 false *1 1.313,3 1.594,3.198 0.281,0.198 10 false B60 2.375,1.292 2.823,1.469 0.448,0.177 10 false THCO 2.063,4.208 2.531,4.406 0.469,0.198 10 false THCO 2.375,1.688 2.615,1.885 0.24,0.198 10 false E2 2.667,0.417 2.833,0.625 0.167,0.208 10 false *2 0.469,2.25 0.635,2.458 0.167,0.208 10 false *3

Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


g.

Read the value.

Standard:

0°C (32°F)


Text in Illustration
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 2)
*2 ECM
*3 Rear view of wire harness connector
(to ECM)


h.

Reconnect the exhaust gas temperature sensor connector.


i.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EXHAUST GAS TEMPERATURE SENSOR)

NG