Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D"/"E" Voltage Correlation  


DESCRIPTION

HINT:

This is the repair procedure for the accelerator pedal position sensor.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is non-contact type.



The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.

In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V, in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting a malfunction.

The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.

E139697E04
1.521,1.969 2.156,1.417 true 1.521,3.406 2.156,3.979 true 0.938,2.271 1.344,1.417 true 0.958,3.156 1.323,4 true 2.542,1.76 2.969,1.938 0.427,0.177 10 false VCPA 1.396,1.281 1.958,1.49 0.563,0.208 10 false Magnet 1.25,4.01 1.729,4.188 0.479,0.177 10 false Magnet 4,1.938 4.313,2.115 0.313,0.177 10 false 4.55 4.677,1.563 4.906,1.74 0.229,0.177 10 false *1 6.24,1.563 6.479,1.76 0.24,0.198 10 false *2 4,2.125 4.323,2.323 0.323,0.198 10 false 3.89 4.01,2.667 4.333,2.844 0.323,0.177 10 false 1.60 4.01,2.906 4.323,3.083 0.313,0.177 10 false 0.80 4.01,3.031 4.333,3.208 0.323,0.177 10 false 0.41 4.219,3.25 4.375,3.427 0.156,0.177 10 false 0 6.771,3.354 7.094,3.531 0.323,0.177 10 false 110 5.083,3.573 5.979,3.75 0.896,0.177 10 false Usable Range 4.385,3.896 6.865,4.073 2.479,0.177 10 false Accelerator Pedal Opening Angle (deg.) 4.406,4.49 6.688,4.667 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.406,4.896 6.771,5.073 2.365,0.177 10 false *2: Accelerator Pedal Fully Depressed 2.573,2.083 2.938,2.26 0.365,0.177 10 false VPA 2.552,2.698 2.958,2.875 0.406,0.177 10 false VPA2 2.573,3.01 2.917,3.188 0.344,0.177 10 false EPA 2.552,3.333 2.969,3.51 0.417,0.177 10 false EPA2 3.99,0.885 5.656,1.271 1.667,0.385 10 false Accelerator Pedal Position Sensor Output Voltage (V) 2.229,1.333 2.771,1.688 0.542,0.354 10 false IC No. 1 2.229,3.927 2.833,4.281 0.604,0.354 10 false IC No. 2

DTC No. DTC Detection Condition Trouble Area
P2120 Condition (a) continues for 1 second or more:
(1 trip detection logic)
(a) VPA less than 0.2 V and VPA2 greater than 2.7 deg, or VPA greater than 4.8 V
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor (built into accelerator link assembly)

·

ECM


P2121 Conditions (a) continue for 1 second or more:
(1 trip detection logic)
(a) Difference between VPA and VPA2 exceeds the threshold
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor (built into accelerator link assembly)

·

ECM


P2122 Conditions (a) and (b) continue for 1 second or more:
(1 trip detection logic)
(a) VPA less than 0.2 V
(b) VPA2 greater than 2.7 deg
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor (built into accelerator link assembly)

·

ECM


P2123 Condition (a) continues for 2 seconds or more:
(1 trip detection logic)
(a) VPA greater than 4.8 V
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor (built into accelerator link assembly)

·

ECM


P2125 Condition (a) continues for 1 second or more:
(1 trip detection logic)
(a) VPA2 less than 0.5 V and VPA greater than 2.7 deg, or VPA2 greater than 4.8 V and VPA greater than 0.2 V but less than 3.45 V
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor (built into accelerator link assembly)

·

ECM


P2127 Conditions (a) and (b) continue for 1 second or more:
(1 trip detection logic)
(a) VPA2 less than 0.5 V
(b) VPA greater than 2.7 deg
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor (built into accelerator link assembly)

·

ECM


P2128 Conditions (a) and (b) continue for 2 seconds or more:
(1 trip detection logic)
(a) VPA2 greater than 4.8 V
(b) VPA greater than 0.2 V but less than 3.45 V
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor (built into accelerator link assembly)

·

ECM


P2138 Condition (a) or (b) continues for 2 seconds or more:
(1 trip detection logic)
(a) Difference between VPA and VPA2 less than 0.02 V
(b) VPA less than 0.2 V and VPA2 less than 0.5 V
·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor (built into accelerator link assembly)

·

ECM



HINT:

When DTC P2120, P2122, P2123, P2125, P2127, P2128 or P2138 is detected, check the output voltage of the accelerator pedal position sensor by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


Trouble Area Accelerator pedal position expressed as voltage output
Accelerator pedal released Accelerator pedal depressed
Accel Sensor Out No. 1 Accel Sensor Out No. 2 Accel Sensor Out No. 1 Accel Sensor Out No. 2
VC circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
VPA circuit open or ground short 0 to 0.2 V 1.4 to 1.8 V 0 to 0.2 V 3.6 to 4.4 V
VPA2 circuit open or ground short 0.6 to 1.0 V 0 to 0.2 V 2.8 to 3.6 V 0 to 0.2 V
EPA circuit open 4.5 to 4.9 V 4.5 to 4.9 V 4.5 to 4.9 V 4.5 to 4.9 V

WIRING DIAGRAM

A185060E04
0.24,2.958 0.51,3.146 0.271,0.188 10 false F9 0.24,3.094 2.719,3.479 2.479,0.385 10 false Accelerator Link Assembly (Accelerator Pedal Position Sensor) 1.448,0.719 1.865,0.906 0.417,0.188 10 false EPA2 1.438,1.188 1.854,1.365 0.417,0.177 10 false VPA2 1.406,1.615 1.865,1.802 0.458,0.188 10 false VCPA 1.5,2.073 1.875,2.26 0.375,0.188 10 false EPA 1.5,2.51 1.865,2.698 0.365,0.188 10 false VPA 5.563,0.75 5.979,0.948 0.417,0.198 10 false EPA2 5.563,1.188 6.01,1.365 0.448,0.177 10 false VPA2 5.563,1.625 5.99,1.833 0.427,0.208 10 false VCPA 5.563,2.083 5.927,2.26 0.365,0.177 10 false EPA 5.563,2.521 5.906,2.719 0.344,0.198 10 false VPA 5.271,0.552 5.479,0.729 0.208,0.177 10 false 29 5.229,1.177 5.521,1.375 0.292,0.198 10 false A54 5.229,1.635 5.521,1.813 0.292,0.177 10 false A54 5.219,2.073 5.552,2.26 0.333,0.188 10 false A54 5.229,2.521 5.521,2.708 0.292,0.188 10 false A54 5.229,0.729 5.542,0.906 0.313,0.177 10 false A54 5.281,0.99 5.5,1.156 0.219,0.167 10 false 23 5.281,1.438 5.51,1.635 0.229,0.198 10 false 20 5.271,1.896 5.479,2.073 0.208,0.177 10 false 28 5.281,2.333 5.49,2.531 0.208,0.198 10 false 22 1.938,0.615 2.094,0.781 0.156,0.167 10 false 2 1.938,1.052 2.083,1.24 0.146,0.188 10 false 1 1.948,1.5 2.073,1.677 0.125,0.177 10 false 4 1.948,1.948 2.083,2.125 0.135,0.177 10 false 3 1.948,2.406 2.083,2.594 0.135,0.188 10 false 5 6.063,3.01 6.458,3.198 0.396,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION)
a.
FI07052E75
0.542,1.792 1.292,1.99 0.75,0.198 10 false Depressed 2.438,1.781 3.115,1.979 0.677,0.198 10 false Released

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the value.

Standard Voltage:
Accelerator Pedal Condition Accel Sensor Out No. 1 Accel Sensor Out No. 2
Released 0.6 to 1.0 V 1.4 to 1.8 V
Depressed 2.8 to 3.6 V 3.6 to 4.4 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)

NG

5.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
a.

Check the wire harness and connector.

i.

Disconnect the accelerator pedal position sensor connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-2 (EPA2) - A54-29 (EPA2) Always Below 1 Ω
F9-1 (VPA2) - A54-23 (VPA2) Always Below 1 Ω
F9-4 (VCPA) - A54-20 (VCPA) Always Below 1 Ω
F9-3 (EPA) - A54-28 (EPA) Always Below 1 Ω
F9-5 (VPA) - A54-22 (VPA) Always Below 1 Ω
F9-2 (EPA2) or A54-29 (EPA2) - Body ground Always 10 kΩ or higher
F9-1 (VPA2) or A54-23 (VPA2) - Body ground Always 10 kΩ or higher
F9-4 (VCPA) or A54-20 (VCPA) - Body ground Always 10 kΩ or higher
F9-3 (EPA) or A54-28 (EPA) - Body ground Always 10 kΩ or higher
F9-5 (VPA) or A54-22 (VPA) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VCPA VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VCPA VOLTAGE)
a.
A225142E09
2.583,0.271 2.948,0.51 0.365,0.24 2.896,0.938 3.01,1.51 true 2.813,1.031 2.375,1.698 true 2.75,1.031 1.792,1.542 true 0.135,0.083 0.375,0.271 0.24,0.188 10 false *a 2.656,0.313 2.979,0.479 0.323,0.167 10 false A54 2.01,1.74 2.688,1.927 0.677,0.188 10 false 28 (EPA) 1.292,1.573 2.01,1.771 0.719,0.198 10 false 29 (EPA2) 2.646,1.542 3.406,1.75 0.76,0.208 10 false 20 (VCPA)

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A54-20 (VCPA) - A54-28 (EPA) Ignition switch ON 4.5 to 5.5 V
A54-20 (VCPA) - A54-29 (EPA2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR LINK ASSEMBLY

NG

4.REPLACE ACCELERATOR LINK ASSEMBLY
a.

Replace the accelerator link assembly (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Turn the ignition switch off and wait for 1 minute or more.


f.

Start the engine.


g.

Allow the engine to idle for 15 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / DTC.


i.

Read the DTCs.


Result:
Result Proceed to
DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 A
No DTC output B



A

B

END