Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM J

N04C-UH ENGINE CONTROL  ECD SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL is not illuminated even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to the ON position. The MIL goes off when the engine is started.


A224410E03
4.375,1.188 6.198,1.365 1.823,0.177 10 false 5 V Constant Voltage Circuit 5.354,2.052 6.365,2.469 1.01,0.417 10 false Microprocessor 1.26,1.135 2.656,1.333 1.396,0.198 10 false from EFI-MAIN Fuse 1.26,1.49 2.719,1.688 1.458,0.198 10 false from EFI NO. 2 Fuse 2.906,1 3.427,1.219 0.521,0.219 10 false BATT 0.302,2.01 2.594,2.552 2.292,0.542 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 0.375,2.948 2.656,3.323 2.281,0.375 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.125 4.333,3.333 0.26,0.208 10 false R 2.99,1.344 3.344,1.542 0.354,0.198 10 false +B 3.167,2.292 3.458,2.49 0.292,0.198 10 false VC 4.938,3.375 5.385,3.604 0.448,0.229 10 false ECM

WIRING DIAGRAM

A431590E01
6.365,8.5 6.771,8.708 0.406,0.208 10 false ECM 6.104,0.438 6.375,0.583 0.271,0.146 10 false PIM 6.083,1.5 6.302,1.646 0.219,0.146 10 false VC 6.094,2.167 6.385,2.313 0.292,0.146 10 false VLU 6.073,3.333 6.469,3.479 0.396,0.146 10 false EGLS 6.104,5.729 6.469,5.917 0.365,0.188 10 false PEX 6.115,6.823 6.552,7.01 0.438,0.188 10 false PCR1 6.104,7.865 6.375,8.052 0.271,0.188 10 false E2 5.708,0.208 5.885,0.365 0.177,0.156 10 false 28 5.698,0.427 6.021,0.583 0.323,0.156 10 false B60 5.729,1.292 5.906,1.448 0.177,0.156 10 false 18 5.698,1.5 5.99,1.698 0.292,0.198 10 false B59 5.74,1.948 5.917,2.104 0.177,0.156 10 false 20 5.698,2.167 6.01,2.354 0.313,0.188 10 false B60 5.74,3.625 5.917,3.781 0.177,0.156 10 false 3 5.698,3.323 6.01,3.51 0.313,0.188 10 false B60 5.74,5.521 5.958,5.719 0.219,0.198 10 false 27 5.688,5.74 6,5.906 0.313,0.167 10 false B60 5.719,6.594 5.938,6.771 0.219,0.177 10 false 26 5.698,6.823 6.021,7 0.323,0.177 10 false B59 5.729,7.615 5.948,7.823 0.219,0.208 10 false 28 5.677,7.865 6.021,8.052 0.344,0.188 10 false B59 2.24,0.188 2.365,0.354 0.125,0.167 10 false 1 2.24,0.438 2.396,0.615 0.156,0.177 10 false 3 4.063,0.323 4.198,0.49 0.135,0.167 10 false 2 2.448,0.313 2.573,0.469 0.125,0.156 10 false E 2.458,0.573 2.74,0.75 0.281,0.177 10 false VC 3.708,0.427 4.01,0.615 0.302,0.188 10 false PIM 2.156,0.844 2.49,1.042 0.333,0.198 10 false B18 2.177,1.021 4.417,1.219 2.24,0.198 10 false Manifold Absolute Pressure Sensor 2.24,1.917 2.375,2.094 0.135,0.177 10 false 2 2.229,2.167 2.354,2.354 0.125,0.188 10 false 1 4.083,2.052 4.229,2.229 0.146,0.177 10 false 3 2.438,2.042 2.688,2.24 0.25,0.198 10 false E2 2.438,2.302 2.708,2.479 0.271,0.177 10 false VC 3.698,2.177 4.031,2.365 0.333,0.188 10 false VTA 2.063,2.448 2.375,2.656 0.313,0.208 10 false B27 2.125,2.615 4.25,2.99 2.125,0.375 10 false Throttle Position Sensor (Built into Diesel Throttle Body Assembly) 2.219,3.292 2.354,3.469 0.135,0.177 10 false 2 2.219,3.719 2.333,3.896 0.115,0.177 10 false 3 4.083,3.208 4.188,3.354 0.104,0.146 10 false 4 2.448,3.406 2.688,3.625 0.24,0.219 10 false E2 2.438,3.854 2.719,4.042 0.281,0.188 10 false VC 3.625,3.875 4.052,4.052 0.427,0.177 10 false EGR 2.167,4.198 2.458,4.396 0.292,0.198 10 false B47 2.177,4.365 4.49,4.74 2.313,0.375 10 false EGR Valve Position Sensor (Built into EGR Valve Assembly) 2.24,5.479 2.365,5.667 0.125,0.188 10 false 1 2.24,5.74 2.365,5.917 0.125,0.177 10 false 3 4.052,5.615 4.177,5.781 0.125,0.167 10 false 2 2.458,5.583 2.708,5.76 0.25,0.177 10 false E2 2.458,5.875 2.729,6.063 0.271,0.188 10 false VC 3.656,5.74 3.99,5.938 0.333,0.198 10 false PEX 2.073,5.948 2.354,6.125 0.281,0.177 10 false A43 2.052,6.156 4.479,6.396 2.427,0.24 10 false Differential Pressure Sensor Assembly 2.26,6.833 2.385,7.021 0.125,0.188 10 false 3 2.448,6.969 2.813,7.188 0.365,0.219 10 false VC1 2.073,7.094 2.385,7.281 0.313,0.188 10 false B92 2.063,7.229 4.031,7.604 1.969,0.375 10 false Fuel Pressure Sensor (Built into Common Rail Assembly) 2.438,6.667 2.708,6.844 0.271,0.177 10 false E1 2.25,6.531 2.375,6.74 0.125,0.208 10 false 1 4.052,6.688 4.188,6.865 0.135,0.177 10 false 2 3.594,6.833 4.01,7.021 0.417,0.188 10 false PCR1 3.552,3.333 3.979,3.51 0.427,0.177 10 false EGLS 4.083,3.75 4.188,3.896 0.104,0.146 10 false 1 5.688,3.865 6,4.052 0.313,0.188 10 false B60 5.75,3.094 5.927,3.25 0.177,0.156 10 false 33 6.073,3.854 6.854,4.208 0.781,0.354 10 false EGRS

A227215E04
6.104,5.99 6.521,6.198 0.417,0.208 10 false ECM 5.75,0.635 6.125,0.823 0.375,0.188 10 false VCG 5.76,1.167 6.021,1.365 0.26,0.198 10 false G+ 5.75,1.656 6,1.833 0.25,0.177 10 false G- 5.75,3.333 6.198,3.521 0.448,0.188 10 false VCPA 5.75,3.854 6.125,4.031 0.375,0.177 10 false VPA 5.75,4.354 6.156,4.573 0.406,0.219 10 false EPA 5.75,4.885 6.188,5.104 0.438,0.219 10 false VPA2 5.75,5.385 6.188,5.604 0.438,0.219 10 false EPA2 5.417,0.417 5.646,0.594 0.229,0.177 10 false 22 5.417,0.927 5.635,1.104 0.219,0.177 10 false 23 5.417,1.427 5.646,1.604 0.229,0.177 10 false 31 5.354,1.646 5.688,1.823 0.333,0.177 10 false B60 5.406,3.115 5.625,3.323 0.219,0.208 10 false 20 5.354,5.365 5.688,5.573 0.333,0.208 10 false A54 5.417,3.625 5.635,3.813 0.219,0.188 10 false 22 5.417,4.135 5.635,4.313 0.219,0.177 10 false 28 5.406,4.656 5.635,4.844 0.229,0.188 10 false 23 5.406,5.146 5.656,5.333 0.25,0.188 10 false 29 1.594,0.615 1.865,0.792 0.271,0.177 10 false VG 1.604,1.115 1.865,1.292 0.26,0.177 10 false G1 1.646,1.667 1.875,1.865 0.229,0.198 10 false G- 1.406,3.333 1.865,3.5 0.458,0.167 10 false VCPA 1.49,3.833 1.865,4.021 0.375,0.188 10 false VPA 1.51,4.354 1.854,4.531 0.344,0.177 10 false EPA 1.438,4.854 1.865,5.042 0.427,0.188 10 false VPA2 1.448,5.396 1.865,5.573 0.417,0.177 10 false EPA2 0.49,2.052 0.76,2.25 0.271,0.198 10 false k2 0.49,2.219 2.219,2.406 1.729,0.188 10 false Camshaft Position Sensor 0.5,5.76 0.781,5.938 0.281,0.177 10 false F9 0.479,5.927 2.948,6.302 2.469,0.375 10 false Accelerator Pedal Position Sensor (Built into Accelerator Link Assembly) 1.927,0.521 2.083,0.698 0.156,0.177 10 false 3 1.927,1.021 2.052,1.208 0.125,0.188 10 false 1 1.938,1.542 2.094,1.708 0.156,0.167 10 false 2 1.927,3.219 2.052,3.406 0.125,0.188 10 false 4 1.927,3.74 2.063,3.927 0.135,0.188 10 false 5 1.927,4.229 2.052,4.438 0.125,0.208 10 false 3 1.927,4.74 2.042,4.927 0.115,0.188 10 false 1 1.927,5.26 2.052,5.448 0.125,0.188 10 false 2 5.365,4.865 5.698,5.073 0.333,0.208 10 false A54 5.354,4.354 5.688,4.563 0.333,0.208 10 false A54 5.365,3.844 5.698,4.052 0.333,0.208 10 false A54 5.354,3.333 5.688,3.542 0.333,0.208 10 false A54 5.354,1.135 5.688,1.313 0.333,0.177 10 false B60 5.365,0.635 5.698,0.813 0.333,0.177 10 false B60

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK MIL
a.

Check that Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Check the communication between the tester and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK DIESEL THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)

B

3.CHECK DIESEL THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the throttle position sensor connector.



A

4.CHECK ACCELERATOR LINK ASSEMBLY (CHECK MIL ILLUMINATED)

B

4.CHECK ACCELERATOR LINK ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the accelerator pedal position sensor connector.



A

5.CHECK CAMSHAFT POSITION SENSOR (CHECK MIL ILLUMINATED)

B

5.CHECK CAMSHAFT POSITION SENSOR (CHECK MIL ILLUMINATED)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the camshaft position sensor connector.



A

6.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (CHECK MIL ILLUMINATED)

B

6.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (CHECK MIL ILLUMINATED)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the manifold absolute pressure sensor connector.



A

7.CHECK EGR VALVE ASSEMBLY (CHECK MIL ILLUMINATED)

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

7.CHECK EGR VALVE ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the EGR valve position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the EGR valve position sensor connector.



A

8.CHECK DIFFERENTIAL PRESSURE SENSOR (CHECK MIL ILLUMINATED)

B

8.CHECK DIFFERENTIAL PRESSURE SENSOR (CHECK MIL ILLUMINATED)
a.

Disconnect the differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the differential pressure sensor connector.



A

9.CHECK COMMON RAIL ASSEMBLY (CHECK MIL ILLUMINATED)

B

9.CHECK COMMON RAIL ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the fuel pressure sensor connector.



A

10.CHECK HARNESS AND CONNECTOR (ECM - EACH SENSOR)

B

REPLACE COMMON RAIL ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (ECM - EACH SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the accelerator pedal position sensor connector.


c.

Disconnect the camshaft position sensor connector.


d.

Disconnect the manifold absolute pressure sensor connector.


e.

Disconnect the EGR valve position sensor connector.


f.

Disconnect the differential pressure sensor connector.


g.

Disconnect the fuel pressure sensor connector.


h.

Disconnect the ECM connectors.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-20 (VCPA) - Body ground Always 10 kΩ or higher
B60-22 (VCG) - Body ground Always 10 kΩ or higher
B59-18 (VC) - Body ground Always 10 kΩ or higher



j.

Reconnect the ECM connectors.


k.

Reconnect the fuel pressure sensor connector.


l.

Reconnect the differential pressure sensor connector.


m.

Reconnect the EGR valve position sensor connector.


n.

Reconnect the manifold absolute pressure sensor connector.


o.

Reconnect the camshaft position sensor connector.


p.

Reconnect the accelerator pedal position sensor connector.


q.

Reconnect the throttle position sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR