Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P1266  Supply Pump Pressure Malfunction  


DESCRIPTION

This DTC is stored when "Fuel Press" is low with respect to "Target Common Rail Pressure", or when the pressure limiter valve remains open.

DTC No. DTC Detection Condition Trouble Area
P1266 The pressure limiter valve remains open for 18 seconds or more due to the suction control valve being stuck open.
(1 trip detection logic)
·

Open or short in injection or supply pump assembly (suction control valve) circuit

·

Injection or supply pump assembly (suction control valve)

·

Fuel filter

·

Fuel pipe

·

ECM


"Fuel Press" is lower than "Target Common Rail Pressure" by the specified amount or more for 20 seconds or more.
(1 trip detection logic)

HINT:
·

The pressure limiter valve is determined to be open when the suction control valve is stuck open.

·

Low fuel pressure indicates that "Fuel Press" cannot increase to the value of "Target Common Rail Pressure" for some reason. Usually, this is detected due to the injection or supply pump assembly not being able to pump an adequate amount of fuel due to a clogged fuel line, etc.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B103-23 (PCV+) - B52-1 (SCV+) Always Below 1 Ω
B103-12 (PCV-) - B52-2 (SCV-) Always Below 1 Ω
B103-23 (PCV+) or B52-1 (SCV+) - Body ground Always 10 kΩ or higher
B103-12 (PCV-) or B52-2 (SCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SUCTION CONTROL VALVE - ECM)

2.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Inspect the injection or supply pump assembly (suction control valve) (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>FUEL SUPPLY PUMP>INSPECTION).


Result:
Proceed to
OK
NG



OK

3.INSPECT DIESEL FUEL FILTER ASSEMBLY

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

3.INSPECT DIESEL FUEL FILTER ASSEMBLY
a.

Check the fuel filter is not clogged.

OK:

Fuel filter is not clogged.



Result:
Proceed to
OK
NG



OK

4.CHECK CLOGGED FUEL PIPE

NG

REPLACE DIESEL FUEL FILTER ASSEMBLY

4.CHECK CLOGGED FUEL PIPE
a.

Check the clogged fuel pipe.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL PIPE