Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  U1123  Lost Communication with Variable Nozzle Type Turbo Charger Module  


DESCRIPTION

The CAN (Controller Area Network) is a serial data communication system for real time application. It is a multiplex communication system designed for on-vehicle use that provides a superior communication speed of 500 kbps and a capability to detect malfunctions. Through the combination of the CANH and CANL bus lines, the CAN is able to maintain communication based on differential voltage.

HINT:
·

Malfunctions in the CAN bus (communication line) can be checked from the DLC3. (Except when the sub bus line of the DLC3 is open.)

·

Diagnostic codes (DTCs) related to CAN communication can be checked by using the GTS.

·

The DLC3 is connected to the CAN communication line, but the CAN communication line cannot detect malfunctions in the DLC3 sub bus line.



DTC No. DTC Detection Condition Trouble Area
U1123 Both of the following conditions are met:

(a) Ignition switch ON

(b) No communication between ECM and turbocharger actuator for more than 0.7 seconds (1 trip detection logic)


·

Open or short in turbo actuator circuit

·

Turbocharger sub-assembly

·

CAN communication system

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (U1123)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.


Result:
Result Proceed to
DTC U1123 is output A
DTC is not output B



A

2.CHECK HARNESS AND CONNECTOR (CAN BUS LINE)

B

2.CHECK HARNESS AND CONNECTOR (CAN BUS LINE)
a.
A227776E04
0.281,0.917 0.708,1.188 0.427,0.271 1.51,1.74 1.76,1.26 true 2.323,1.75 2.135,1.25 true 0.208,0.188 0.438,0.365 0.229,0.177 10 false *a 0.448,0.958 0.823,1.156 0.375,0.198 10 false j5 1.323,1.771 1.813,1.969 0.49,0.198 10 false CANL 2.125,1.771 2.615,1.969 0.49,0.198 10 false CANH

Disconnect the turbocharger actuator connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
j5-4 (CANH) - j5-3 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Turbocharger Actuator)


Result:
Proceed to
OK
NG



OK

3.CHECK TURBOCHARGER SUB-ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAN BUS LINE)

3.CHECK TURBOCHARGER SUB-ASSEMBLY (POWER SOURCE)
a.
A227776E05
0.281,0.917 0.708,1.188 0.427,0.271 1.052,1.74 1.302,1.26 true 1.865,1.76 1.677,1.26 true 0.208,0.188 0.438,0.365 0.229,0.177 10 false *a 0.448,0.958 0.823,1.156 0.375,0.198 10 false j5 0.885,1.771 1.375,1.969 0.49,0.198 10 false HLV 1.76,1.802 2.25,2 0.49,0.198 10 false HLG

Disconnect the turbocharger sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
j5-1 (HLV) - j5-2 (HLG) Ignition switch ON 9 to 16 V


Text in Illustration
*a Front view of wire harness connector
(to Turbocharger Sub-assembly)


Result:
Proceed to
OK
NG



OK

REPLACE TURBOCHARGER SUB-ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (TURBOCHARGER SUB-ASSEMBLY - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (TURBOCHARGER SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the turbocharger sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j5-2 (HLG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TURBOCHARGER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TURBOCHARGER SUB-ASSEMBLY - BODY GROUND)