Home › Engine / Hybrid System › N04C-VQ (FUEL) › FUEL SUPPLY PUMP › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073145 N04C-VQ FUEL _0355915 FUEL SUPPLY PUMP A

N04C-VQ FUEL  FUEL SUPPLY PUMP  INSTALLATION  


PROCEDURE

Hide 13613 1.INSTALL INJECTION PUMP DRIVE GEAR

a.

Clamp the injection pump assembly in a vise.


b.

Install the crankshaft angle sensor plate and the injection pump drive gear with the nut.

Torque:

64 N*m (650 kgf*cm, 47 ft.*lbf)



c.

Install a new O-ring onto the timer cover.


d.

Install the timer cover onto the supply pump with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



Hide 22100 2.INSTALL SUPPLY PUMP ASSEMBLY

a.

Install a new O-ring onto the timer cover.


b.
A146751E03
2.545,0.15 2.727,0.345 0.182,0.194 10 *a 2.952,0.584 3.138,0.779 0.186,0.194 10 *b 2.516,0.265 2.311,0.512 false 2.9,0.683 2.089,0.814 false

Turn the drive gear and align the hole with the matchmark as shown in the illustration.

Text in Illustration
*a Matchmark
*b Hole


c.
A146510E15
2.635,1.021 1.875,0.198 false 1.677,0.094 1.875,0.365 0.198,0.271 10 false *a

Check that the No. 1 cylinder is at TDC/compression.

*a Timing Mark


d.
A259946E02
0.333,0.188 0.5,0.188 0.5,0.188 0.635,0.656 true 0.177,0.104 0.49,0.302 0.313,0.198 10 false *a

Align the matchmarks of the timer cover and the front end plate, and then install the supply pump assembly with the 4 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)


Text in Illustration
*a Matchmark


e.
A101551

When the crankshaft position sensor installation hole can be accessed directly:

i.

Check that the knock pin of the injection pump drive gear is at the center of the hole.



f.
A146792E07
1.76,1.49 1.948,1.208 false 2.208,0.656 2.375,0.823 0.167,0.167 10 false *b 3.063,1.073 3.229,1.24 0.167,0.167 10 false *c 1.656,1.458 1.823,1.625 0.167,0.167 10 false *a

When the crankshaft position sensor installation hole cannot be accessed directly:

i.

Tape the screwdriver as shown in the illustration.

Text in Illustration
*a Vinyl Tape
*b 36 mm (1.42 in.)
*c 6 mm (0.236 in.)


ii.
A146793E03
2.874,0.347 3.109,0.721 0.235,0.374 10 *1 2.854,0.478 2.227,1.187 false

Remove the service plug and gasket from the timing chain cover sub-assembly.

Text in Illustration
*1 Service Plug


iii.
A258992E01
0.698,2.729 0.865,2.729 0.865,2.729 0.927,2.958 false 0.844,0.5 1.01,0.5 1.01,0.5 1.073,0.729 false 1.688,0.292 1.854,0.292 1.854,0.292 1.979,0.74 true 1.708,2.521 1.875,2.521 1.875,2.521 2,2.969 true 2.208,2.167 2.375,2.167 2.375,2.167 2.458,1.844 true 2.229,4.406 2.396,4.406 2.396,4.406 2.479,4.083 true 1.552,0.198 1.771,0.417 0.219,0.219 10 false *1 0.698,0.396 0.917,0.615 0.219,0.219 10 false *a 1.573,1.354 1.792,1.573 0.219,0.219 10 false *b 2.031,2.083 2.25,2.302 0.219,0.219 10 false *2 2.063,4.313 2.281,4.531 0.219,0.219 10 false *2 1.427,3.583 1.646,3.802 0.219,0.219 10 false *c 0.542,2.635 0.76,2.854 0.219,0.219 10 false *a 1.573,2.438 1.792,2.656 0.219,0.219 10 false *1

Insert the taped screwdriver it into the timing gear case. Check that the tape and end of the timing gear case are aligned.

Text in Illustration
*1 Timing Chain Cover
*2 Injection Pump Drive Gear
*a Screwdriver
*b 0 to 2 mm of the tape is visible
*c 10 mm or more of the tape is visible


iv.

Install the service plug and a new gasket to the timing chain cover sub-assembly.

Torque:

8.0 N*m (82 kgf*cm, 71 ft.*lbf)




g.

Install the injection pump stay with a nut and 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



h.

Connect the 2 connectors.


Hide 23811 3.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE

a.

Temporarily install the fuel filter to injection pump fuel pipe.


b.

Using a 17 mm union nut wrench, install the fuel filter to injection pump fuel pipe with the 2 union nuts.

Torque:
Specified tightening torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·
A329093E12
1.688,0.604 2,0.802 0.313,0.198 10 false *a

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)

Text in Illustration
*a Torque Wrench Fulcrum Length




c.

Install the fuel pipe clamp with the nut.

HINT:

Tighten the nut until the clamp edge makes contact with the engine side clamp edge.



Hide 23802E 4.INSTALL FUEL PIPE SUB-ASSEMBLY

a.
A261046E02
0.25,0.927 0.385,1.073 0.135,0.146 10 true C 1.021,2.208 1.156,2.354 0.135,0.146 10 true A 2.854,0.75 2.99,0.896 0.135,0.146 10 true A 3.219,1.74 3.354,1.885 0.135,0.146 10 true A 2.271,2.323 2.406,2.469 0.135,0.146 10 true B

Install 8 gaskets and fuel pipe with the 5 union bolts.

Torque:
for bolt A:

25 N*m (255 kgf*cm, 18 ft.*lbf)

for bolt B:

20 N*m (200 kgf*cm, 15 ft.*lbf)

for bolt C:

42 N*m (428 kgf*cm, 31 ft.*lbf)



b.

Connect the 2 fuel tubes.


c.

Install the 4 fuel pipe clamps with the 4 nuts.

HINT:

Tighten the nut until the clamp edge makes contact with the engine side clamp edge.



Hide 58396E 5.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



b.

Connect the engine wire with nut.

Torque:

8.4 N*m (86 kgf*cm, 74 ft.*lbf)



c.
A261390E01
0.771,0.677 0.906,0.875 0.135,0.198 10 true A 2.49,1.396 2.625,1.594 0.135,0.198 10 true B

Install the 2 wire harness clamp brackets with 2 bolts.

Torque:
for bolt A:

32 N*m (327 kgf*cm, 24 ft.*lbf)

for bolt B:

29 N*m (291 kgf*cm, 21 ft.*lbf)



d.

Connect the ground wire with bolt.

Torque:

8.4 N*m (86 kgf*cm, 74 ft.*lbf)



e.

Connect the connector and 3 clamps.


Hide 17113D 7.INSTALL NO. 1 INTAKE PIPE

Hide 11213 8.INSTALL CYLINDER HEAD COVER GASKET

Hide 11228 9.INSTALL CYLINDER HEAD COVER CUSHION

Hide 11202D 10.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11202F 11.INSTALL CYLINDER HEAD COVER CUSHION RUBBER

Hide 11201 12.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12180E 13.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 25608 14.INSTALL EGR COOLER SUB-ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 20.SUPPLY PUMP INITIALIZATION