Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS (for Luggage Compartment)
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356203 BACK WINDOW GLASS(for Luggage Compartment) A

WINDOW / GLASS  BACK WINDOW GLASS(for Luggage Compartment)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 64810 1.CLEAN BACK WINDOW ASSEMBLY

a.
E268586

Clean the outer edge of the back window glass with non-residue solvent.

NOTICE:
·

Do not touch the back window assembly surface after cleaning it.

·

Do not damage the glass.

·

Even if using a new back window assembly, clean the back window assembly with non-residue solvent.




Hide 64819A 2.INSTALL NO. 2 BACK WINDOW GLASS SPACER

a.

Using non-residue solvent, clean the No. 2 back window glass spacer installation surface of the vehicle body.


b.

Install the body primer to the No. 2 back window glass spacer installation surface of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new No. 2 back window glass spacer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 4 No. 2 back window glass spacers to the body panel as shown in the illustration.

B474320E01
2.646,0.49 2.802,0.688 0.156,0.198 10 true A 2.646,0.854 2.802,1.052 0.156,0.198 10 true A 2.583,3.313 2.74,3.51 0.156,0.198 10 false B 2.573,2.938 2.729,3.135 0.156,0.198 10 false B 4.813,0.156 5.219,0.323 0.406,0.167 10 false A-A 4.875,1.938 5.281,2.104 0.406,0.167 10 false B-B


Hide 56114C 3.INSTALL WINDSHIELD GLASS RETAINER

a.

Using non-residue solvent, clean the windshield glass retainer installation surface of the back window assembly.


b.

Install the glass primer to the windshield glass retainer installation surface of the back window assembly.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new windshield glass retainer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 4 windshield glass retainers to the back window assembly as shown in the illustration.

B474321E01
2.104,0.844 1.74,0.75 1.74,0.75 2.094,0.729 true 2.021,3.083 1.656,2.99 1.656,2.99 2.01,2.969 true 2.448,3.083 2.854,3.031 2.854,3.031 2.438,2.969 true 2.531,0.844 2.938,0.792 2.938,0.792 2.521,0.729 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 1.531,0.667 1.76,0.854 0.229,0.188 10 false *b 3,0.708 3.229,0.896 0.229,0.188 10 false *b 2.917,2.948 3.146,3.135 0.229,0.188 10 false *b 1.438,2.885 1.667,3.073 0.229,0.188 10 false *b 2.542,0.26 2.719,0.417 0.177,0.156 10 true A 2.542,0.917 2.719,1.073 0.177,0.156 10 true A 1.896,2.729 2.031,2.896 0.135,0.167 10 true B 1.906,3.438 2.042,3.604 0.135,0.167 10 true B 4.917,0.125 5.26,0.292 0.344,0.167 10 false A-A 4.885,1.896 5.229,2.063 0.344,0.167 10 false B-B 5.927,0.615 6.083,0.813 0.156,0.198 10 false a 5.958,3.01 6.115,3.208 0.156,0.198 10 false b

Text in Illustration
*a Back Side *b Ceramic Notch

Standard:
Area Specified Condition
a 22.2 mm (0.874 in.)
b 37.0 mm (1.46 in.)



Hide 68299A 4.INSTALL BACK DOOR GLASS SPACER

a.

Using non-residue solvent, clean the back door glass spacer installation surface of the back window assembly.


b.

Install the glass primer to the back door glass spacer installation surface of the back window assembly.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back door glass spacer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 14 back door glass spacers to the back window assembly as shown in the illustration.

B474322E01
0.698,1.896 0.385,1.156 0.385,1.156 0.708,1.458 true 2.938,0.875 2.167,1.021 2.167,1.021 2.479,0.875 true 2.958,3.198 3.5,3.458 3.5,3.458 2.469,3.198 true 4.76,1.479 5.208,2.198 5.208,2.198 4.771,1.906 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.958,0.25 3.115,0.417 0.156,0.167 10 true A 2.948,0.927 3.104,1.094 0.156,0.167 10 true A 0.302,1.885 0.458,2.052 0.156,0.167 10 true B 1.031,1.885 1.188,2.052 0.156,0.167 10 true B 2.875,2.719 3.031,2.885 0.156,0.167 10 true B 2.917,3.479 3.073,3.646 0.156,0.167 10 true B 4.344,1.344 4.5,1.51 0.156,0.167 10 true B 5.073,1.333 5.229,1.5 0.156,0.167 10 true B 0.188,1.031 0.427,1.198 0.24,0.167 10 false *b 1.958,0.958 2.198,1.125 0.24,0.167 10 false *b 3.542,3.406 3.781,3.573 0.24,0.167 10 false *b 5.25,2.177 5.49,2.344 0.24,0.167 10 false *b 5.646,0.104 5.969,0.292 0.323,0.188 10 false A-A 5.667,2.042 5.99,2.229 0.323,0.188 10 false B-B 5.677,0.688 5.833,0.885 0.156,0.198 10 false a 5.74,2.906 5.896,3.104 0.156,0.198 10 false b

Text in Illustration
*a Back Side *b Ceramic Notch

Standard:
Area Specified Condition
a 3.0 mm (0.118 in.)
b 20.0 mm (0.787 in.)



Hide 64828C 5.INSTALL BACK WINDOW GLASS CLIP LH

a.

Using non-residue solvent, clean the back window glass clip LH installation surface of the back window assembly.


b.

Install the glass primer to the back window glass clip LH installation surface of the back window assembly.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass clip LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.
B474323E01
1.458,2.604 1.052,2.385 1.052,2.385 1.469,2.198 true 2.188,2.604 2.51,2.406 2.51,2.406 2.198,2.208 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.833,2.313 1.063,2.5 0.229,0.188 10 false *b 2.573,2.354 2.802,2.542 0.229,0.188 10 false *b

Install the back window glass clip LH to the back window assembly as shown in the illustration.

Text in Illustration
*a Back Side
*b Ceramic Notch


Hide 64827D 6.INSTALL BACK WINDOW GLASS CLIP

a.

Using non-residue solvent, clean the back window glass clip installation surface of the back window assembly.


b.

Install the glass primer to the back window glass clip installation surface of the back window assembly.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass clip.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.
B474324E01
1.323,2.604 0.969,2.375 0.969,2.375 1.323,2.198 true 2.042,2.594 2.396,2.385 2.396,2.385 2.042,2.188 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.74,2.302 0.948,2.469 0.208,0.167 10 false *b 2.469,2.313 2.677,2.479 0.208,0.167 10 false *b

Install the back window glass clip to the back window assembly as shown in the illustration.

Text in Illustration
*a Back Side
*b Ceramic Notch


Hide 64810 7.INSTALL BACK WINDOW ASSEMBLY

a.

Clean and shape the contact surface of the vehicle body.

i.
B455055E01
0.583,1.177 0.583,1.448 false 0.5,1.479 0.813,1.677 0.313,0.198 10 false *a 3.115,0.375 3.26,0.552 0.146,0.177 10 false a

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

Standard:
Area Specified Condition
a 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.)



ii.

Clean the contact surface of the vehicle body with non-residue solvent.

Text in Illustration
*a Vehicle Body
V100155

Adhesive



b.

Position the back window assembly.

i.

Using suction cups, place the back window assembly in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.
B474311E02
1.844,0.417 2.26,0.26 2.26,0.26 1.854,0.719 true 2.302,0.156 2.531,0.344 0.229,0.188 10 false *a

When using a new back window assembly:

Place matchmarks on the back window assembly and vehicle body at the locations indicated in the illustration.

Text in Illustration
*a Matchmarks


iv.

Using suction cups, remove the back window assembly.


v.

Using a brush or sponge, apply body primer to the exposed part of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




vi.

Using a brush or sponge, apply glass primer to the contact surface of the glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B474325E01
1.99,1.021 2.146,1.219 0.156,0.198 10 false A 1.99,1.417 2.146,1.615 0.156,0.198 10 false A 0.135,1.833 0.271,2.01 0.135,0.177 10 false B 0.51,1.823 0.646,2 0.135,0.177 10 false B 3.115,1.406 3.271,1.563 0.156,0.156 10 false C 3.49,1.396 3.646,1.552 0.156,0.156 10 false C 1.979,2.208 2.135,2.365 0.156,0.156 10 false C 1.979,2.583 2.135,2.74 0.156,0.156 10 false C 0.156,0.115 0.427,0.302 0.271,0.188 10 false *a 3.875,0.24 4.167,0.396 0.292,0.156 10 false A-A 5.573,0.24 5.865,0.396 0.292,0.156 10 false B-B 3.885,2.01 4.177,2.167 0.292,0.156 10 false C-C 4.198,0.677 4.354,0.854 0.156,0.177 10 false a 4.479,0.365 4.635,0.542 0.156,0.177 10 false b 5.927,0.865 6.083,1.042 0.156,0.177 10 false a 6.25,0.604 6.406,0.781 0.156,0.177 10 false c 4.906,2.542 5.063,2.719 0.156,0.177 10 false a 4.573,2.208 4.729,2.385 0.156,0.177 10 false b

Text in Illustration
*a Back Side - -
V100155

Glass Primer Application Area - -

Standard:
Area Specified Condition
a 7.0 mm (0.276 in.)
b 14.0 mm (0.551 in.)
c 29.0 mm (1.14 in.)




c.

Apply adhesive to the back window assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



d.
B214800E33
2.49,0.583 2.958,0.406 true 1.292,1.427 1.563,1.646 0.271,0.219 10 false a 3,0.292 3.25,0.552 0.25,0.26 10 false *1 0.583,0.625 0.833,0.865 0.25,0.24 10 false a 1.115,0.906 1.427,1.135 0.313,0.229 10 false b 0.76,1.021 0.958,1.229 0.198,0.208 10 false b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


Text in Illustration
*1 Sealer Gun

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.



e.

Load the sealer gun with the cartridge.


f.

Apply adhesive to the glass as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B474326E01
4.333,1.51 4.531,1.26 true 6.469,1.417 6.104,1.594 6.104,1.594 6.219,1.417 true 4.417,3.25 4.615,3 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.979,1.125 2.135,1.281 0.156,0.156 10 false A 1.979,1.51 2.135,1.667 0.156,0.156 10 false A 0.156,1.906 0.313,2.063 0.156,0.156 10 false B 0.531,1.906 0.688,2.063 0.156,0.156 10 false B 1.99,2.292 2.146,2.448 0.156,0.156 10 false C 1.99,2.688 2.146,2.844 0.156,0.156 10 false C 3.104,1.49 3.26,1.646 0.156,0.156 10 false C 3.479,1.49 3.635,1.646 0.156,0.156 10 false C 3.865,0.302 4.198,0.458 0.333,0.156 10 false A-A 5.583,0.302 5.917,0.458 0.333,0.156 10 false B-B 3.885,2.083 4.219,2.24 0.333,0.156 10 false C-C 4.313,0.625 4.458,0.781 0.146,0.156 10 false a 6.01,0.76 6.156,0.917 0.146,0.156 10 false a 4.792,2.375 4.938,2.531 0.146,0.156 10 false a 6.156,0.49 6.302,0.646 0.146,0.156 10 false b 4.146,1.5 4.354,1.677 0.208,0.177 10 false *b 5.948,1.573 6.156,1.75 0.208,0.177 10 false *b 4.25,3.219 4.458,3.396 0.208,0.177 10 false *b

Text in Illustration
*a Back Side *b Adhesive Center
V100155

Adhesive - -

Standard:
Area Specified Condition
a 14.0 mm (0.551 in.)
b 22.0 mm (0.866 in.)



g.

Install the back window assembly to the vehicle body.


h.
B474313

Using suction cups, position the back window assembly so that the matchmarks are aligned.


i.

Press it in gently along the rim.

NOTICE:
·

Check that the back window glass clip LH and back window glass clip are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.



HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



j.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive to the glass rim.



Hide 8.INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 87950 9.INSTALL OUTER UNDER REAR VIEW MIRROR ASSEMBLY

Hide 10.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85192R 11.INSTALL REAR WIPER ARM COVER

Hide 63316A 12.INSTALL NO. 6 ROOF HEADLINING

Hide 65905B 13.INSTALL WINDOW CURTAIN RAIL SUB-ASSEMBLY (w/ Curtain)

Hide 62511R 14.INSTALL REAR BODY REAR INSIDE TRIM RH

Hide 62512R 15.INSTALL REAR BODY REAR INSIDE TRIM LH

Hide 62227 16.INSTALL QUARTER PILLAR COVER RH

Hide 62228 17.INSTALL LOWER QUARTER PILLAR COVER LH

Hide 62471D 18.INSTALL REAR UPPER PILLAR GARNISH RH

Hide 62472D 19.INSTALL REAR UPPER PILLAR GARNISH LH

Hide 64735A 20.INSTALL CENTER BACK INNER RAIL GARNISH (w/ Lift Up Type)

Hide 58614A 21.INSTALL NO. 4 MAT SET PLATE

Hide 22.INSTALL ROOM RACK ASSEMBLY (w/ Room Rack)

Hide 23.INSTALL REAR SEAT ASSEMBLY (for Rear End)