Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
1.INSTALL FRONT SIDE WINDOW GLASS LH
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 1.0 to 3.0 mm (0.0394 to 0.118 in.) |
| *a | Vehicle Body |
|
Adhesive |
Clean the contact surface of the vehicle body with non-residue solvent.
Position the front side window glass LH.
Using suction cups, place the front side window glass LH in the correct position.
Check that the entire contact surface of the glass rim is perfectly even.
Using suction cups, remove the front side window glass LH.
Using a brush or sponge, apply body primer to the exposed part of the vehicle body.
Do not apply too much primer.
Do not apply primer to the adhesive.
When applying the primer, take care of the seams of the panel and spot welds.
Using a brush or sponge, apply primer to the contact surface of the front side window glass LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | - | - |
|
Primer Application Area | - | - |
Apply adhesive to the front side window glass LH.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| *1 | Sealer Gun |
Apply adhesive to the glass as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | Adhesive Center |
|
Adhesive | - | - |
| Area | Specified Condition |
|---|---|
| a | 9.0 mm (0.354 in.) |
| b | 5.0 mm (0.197 in.) |
| c | 8.0 mm (0.315 in.) |
Using suction cups, attach the 3 No. 1 side window clips and install the front side window glass LH.
Press it in gently along the rim.
Check that the stoppers are attached to the vehicle body correctly.
Check that the vehicle body and glass have a small gap between them.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to the glass rim.
2.INSPECT FOR LEAKS AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
62520G
3.INSTALL SIDE NO. 1 TRIM ASSEMBLY LH
62540A
4.INSTALL SIDE NO. 2 TRIM ASSEMBLY LH
67676
5.INSTALL FRONT SIDE TRIM BOARD COVER LH
73224
6.INSTALL FRONT SEAT BELT RETRACTOR COVER LH (w/ Rear No. 1 Seat)
62638A
7.INSTALL QUARTER PILLAR GARNISH RH
62989
8.INSTALL CENTER DOOR LOCK COVER (for Folding Type)
63310
9.INSTALL ROOF HEADLINING ASSEMBLY
63651B
10.INSTALL AIR INTAKE NET (w/ Rear Air Duct)
63656D
11.INSTALL CENTER AIR INTAKE COVER (w/ Rear Air Duct)
87810
12.INSTALL INNER REAR VIEW MIRROR ASSEMBLY
83910G
13.INSTALL CLOCK ASSEMBLY (w/ Clock)
63310A
14.INSTALL ROOF HEADLINING ASSEMBLY HOLE PLUG (w/ Cover)
74320
15.INSTALL VISOR ASSEMBLY LH (w/ Passenger Side Visor)
74310
16.INSTALL VISOR ASSEMBLY RH
63610
17.INSTALL NO. 1 AIR OUTLET REGISTER ASSEMBLY (w/ Rear Air Duct)
63371B
18.INSTALL NO. 1 ROOF BOARD SET MOULDING
62547B
19.INSTALL NO. 3 PILLAR GARNISH LH (w/o Rear Air Duct)
73220
20.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 1 Seat)
74730
21.INSTALL HAND GRIP FRAME ASSEMBLY (w/ Hand Grip Frame, w/o Rear Air Duct)
62425
22.INSTALL CENTER PILLAR GARNISH COVER (w/ Hand Grip Frame)
62212
23.INSTALL FRONT PILLAR GARNISH LH
62211
24.INSTALL FRONT PILLAR GARNISH RH
74603
25.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY
74617V
26.INSTALL ASSIST GRIP PLUG
63951
27.INSTALL COOLER PIPE COVER
62413A
28.INSTALL LOWER CENTER PILLAR GARNISH RH
73210
29.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
73233
30.INSTALL OUTER LAP BELT ANCHOR COVER
62311C
31.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
58651A
32.INSTALL FRONT DOOR NO. 1 MAT PLATE
46243
33.INSTALL PARKING BRAKE LEVER COVER
34.INSTALL FRONT PILLAR END COVER LH
53182A
35.INSTALL HEADLIGHT COVER LH
87940
36.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
87945
37.INSTALL OUTER MIRROR COVER LH
38.INSTALL FRONT SEAT
39.CONNECT BATTERY NEGATIVE TERMINAL