Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
1.INSTALL REAR SIDE FRONT WINDOW GLASS RH
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 1.0 to 3.0 mm (0.0394 to 0.118 in.) |
Clean the contact surface of the vehicle body with non-residue solvent.
| *a | Vehicle Body |
|
Adhesive |
Using non-residue solvent, clean the rear side front window glass RH installation surface of the vehicle body.
Install the body primer to the rear side front window glass RH installation surface of the vehicle body.
Do not apply too much primer.
Do not apply primer to the adhesive.
When applying the primer, take care of the seams of the panel and spot welds.
Install the suction cups to the rear side front window glass RH.
for Slide Type:
Using a brush or sponge, apply primer to the contact surface of the rear side front window glass RH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | - | - |
|
Primer Application Area | - | - |
Apply adhesive to the rear side front window glass RH.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| *a | Sealer Gun |
Apply adhesive to the rear side front window glass RH as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | R End |
|
Adhesive | - | - |
| Area | Specified Condition |
|---|---|
| a | 9.0 mm (0.354 in.) |
| b | 13.0 mm (0.512 in.) |
| c | 5.0 mm (0.197 in.) |
Fixed Type:
Using a brush or sponge, apply glass primer to the contact surface of the rear side front window glass RH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | - | - |
|
Glass Primer Application Area | - | - |
Apply adhesive to the rear side front window glass RH.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| *a | Sealer Gun |
Apply adhesive to the rear side front window glass RH as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | Adhesive Center |
|
Adhesive | - | - |
Using suction cups, attach the 4 side window glass spacers and install the rear side front window glass RH.
Press it in gently along the rim.
Check that the side window glass spacers, side window frame retainers are attached to the vehicle body correctly.
Check that the vehicle body and glass have a small gap between them.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to the glass rim.
2.INSPECT FOR LEAKS AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
75505
3.INSTALL FRONT ROOF SIDE GARNISH SUB-ASSEMBLY RH
4.INSTALL SIDE PANEL
for RHD:
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for RHD)>INSTALLATION
for LHD:
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for LHD)>INSTALLATION
5.INSTALL ROOF HEADLINING
6.INSTALL REAR SEAT ASSEMBLY (for Rear End)
for Tumble Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>INSTALLATION
for Fixed Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>INSTALLATION