Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
1.REMOVE REAR SEAT ASSEMBLY (for Rear End)
for Tumble Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>REMOVAL
for Fixed Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>REMOVAL
45619K
2.REMOVE KNUCKLE STOPPER COVER (w/ Room Rack)
3.REMOVE ROOM RACK ASSEMBLY (w/ Room Rack)
63372A
4.REMOVE NO. 2 ROOF BOARD SET MOULDING (w/ Rear Air Duct)
63372F
5.REMOVE NO. 3 ROOF BOARD SET MOULDING (w/ Rear Air Duct)
63324
6.REMOVE NO. 4 ROOF BOARD (for Long Body, w/ Rear Air Duct)
65937
7.REMOVE NO. 2 CURTAIN RAIL (w/ Curtain)
65936
8.REMOVE NO. 1 CURTAIN RAIL (w/ Curtain)
63323
9.REMOVE NO. 3 ROOF BOARD (w/ Rear Air Duct)
63940
10.REMOVE NO. 4 INNER COOLER DUCT LH (for Long Body, w/ Rear Air Duc)
63917A
11.REMOVE NO. 3 INNER COOLER DUCT LH
58614A
12.REMOVE NO. 4 MAT SET PLATE
66301D
13.REMOVE ROPE HOOK SUB-ASSEMBLY (w/ Rope Hook)
64735A
14.REMOVE CENTER BACK RAIL INNER GARNISH (for Lift Up Type)
65905B
15.REMOVE WINDOW CURTAIN RAIL SUB-ASSEMBLY (for Lift Up Type, w/ curtain)
63349A
16.REMOVE REAR ROOF HEADLINING GARNISH (for Double Swing Out Type)
62487A
17.REMOVE INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)
62488A
18.REMOVE INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)
62471D
19.REMOVE REAR UPPER PILLAR GARNISH RH
62472D
20.REMOVE REAR UPPER PILLAR GARNISH LH
62228
21.REMOVE LOWER QUARTER PILLAR COVER LH
62512R
22.REMOVE REAR BODY INSIDE TRIM REAR LH
63316A
23.REMOVE NO. 6 ROOF HEADLINING
24.REMOVE SIDE PANEL
for RHD:
Perform the linked removal procedures until the No. 3 side trim assembly LH.
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for RHD)>REMOVAL
for LHD:
Perform the linked removal procedures until the No. 3 side trim assembly RH.
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for LHD)>REMOVAL
63372A
25.REMOVE NO. 2 ROOF BOARD SET MOULDING (w/o Rear Air Duct)
63377C
26.REMOVE NO. 2 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
63378C
27.REMOVE NO. 3 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
63372G
28.REMOVE NO. 4 ROOF BOARD SET MOULDING (w/o Rear Air Duct)
62452B
29.REMOVE NO. 3 ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
62431F
30.REMOVE ROOF SIDE RAIL GARNISH (for Long Body, w/o Rear Air Duct)
62451E
31.REMOVE REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)
32.REMOVE REAR SIDE FRONT WINDOW GLASS LH
The rear side front window glass LH may fall while performing this procedure. Therefore, use suction cups to hold the rear side front window glass LH from the outside of the vehicle.
Apply protective tape to the outer surface of the vehicle body and glass to prevent scratches.
for Long Body:
| *1 | Protective Tape |
for Standard Body:
| *1 | Protective Tape |
Install the suction cups to the rear side front window glass LH.
Apply a sufficient amount of soapy water to the adhesive.
Start this procedure where the rear side front window glass LH and body are furthest apart.
From the interior, insert a knife between the vehicle body and glass.
Cut through the adhesive by knife around the glass.
Using suction cups, disconnect the 4 spacers and remove the rear side front window glass LH.
Be careful not to drop the rear side front window glass LH.
for Long Body:
for Standard Body: