Home › Vehicle Interior › EXTERIOR › BLACK OUT TAPE
RM2850E _58 Vehicle Interior _073214 EXTERIOR _0356393 BLACK OUT TAPE A

EXTERIOR  BLACK OUT TAPE  INSTALLATION  


PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.

NOTICE:
·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light.

When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape.

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in a place with a high temperature.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf. 4.5 to 6.7 lbf.) while moving the squeegee at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.

B233855E18
0.083,0.073 3.875,1.563 3.792,1.49 0.688,0.625 0.833,0.479 0.833,0.479 1,0.479 false 2.177,0.74 2.292,0.365 2.292,0.365 2.542,0.365 false 2.135,1.25 2.833,1.25 false 2.146,1.99 2.146,1.823 2.146,1.823 2.604,1.823 true 2.094,3.427 2.646,3.427 true 4.594,2.625 4.99,2.625 false 4.875,3.052 5.302,3.052 false 5.698,2.635 5.938,2.979 5.938,2.979 6.052,2.979 true 5.677,3.271 6.073,3.271 false 1.021,2.865 1.781,2.865 1.781,2.865 2.021,2.281 false 1.125,3.26 1.646,3.26 false 4.552,2.24 5,2.5 0.448,0.26 10 false *e 2.698,1.729 3.292,1.969 0.594,0.24 10 false *d 6.125,2.885 6.583,3.198 0.458,0.313 10 false *g 2.885,2.385 3.281,2.698 0.396,0.313 10 false *f 0.167,0.104 0.427,0.385 0.26,0.281 10 false *a 2.594,0.281 2.875,0.542 0.281,0.26 10 false *b 2.885,1.167 3.198,1.448 0.313,0.281 10 false *c 1.021,0.396 1.323,0.667 0.302,0.271 10 false *1 0.813,2.792 1.146,3.052 0.333,0.26 10 false *1 0.094,1.635 0.5,1.906 0.406,0.271 10 false *A 0.938,3.177 1.229,3.406 0.292,0.229 10 false *2 4.406,2.542 4.708,2.802 0.302,0.26 10 false *1 4.667,2.979 5.063,3.25 0.396,0.271 10 false *2 2.688,3.344 2.958,3.573 0.271,0.229 10 false *3 3.677,1.635 4,1.885 0.323,0.25 10 false *B 6.115,3.198 6.51,3.469 0.396,0.271 10 false *3 1.083,2.25 1.531,2.51 0.448,0.26 10 false *e 6.354,2.042 6.75,2.354 0.396,0.313 10 false *f

Text in Illustration
*A Pressing *B Pulling
*1 Squeegee *2 Black Out Tape
*3 Release Paper - -
*a Sectional View *b Non-padded Side
*c Padded Side *d 40 to 50° (for pressing forward)
*e 30 to 70 mm/sec. (1.18 to 2.76 in/sec.) *f 10 to 20 mm (0.39 to 0.79 in.)
*g 30 to 45° (for pulling) - -

HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.39 to 0.78 in.) from the edge of the squeegee.



NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.




f.
B233856E04
0.969,1.792 1.083,1.792 1.083,1.792 1.198,1.698 false 0.74,1.698 0.938,1.854 0.198,0.156 10 false *1 2.333,0.438 2.51,0.615 0.177,0.177 10 false *a 1.625,0.333 1.823,0.51 0.198,0.177 10 false *b 0.906,0.427 1.115,0.625 0.208,0.198 10 false *c 1.771,1.833 2.104,2.031 0.333,0.198 10 false *2

Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).

i.

If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

Text in Illustration
*1 Squeegee
*2 Hem
*a First
*b Second
*c Third

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.



h.

Check after installation.

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75937 2.INSTALL REAR ROOF STRIPE

HINT:

When installing the rear roof stripe, heat the vehicle body and rear roof stripe using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
Rear Roof Stripe 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not heat the vehicle body or rear roof stripe excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Refer to the illustration to position a new rear roof stripe.

B467503E01
1.156,1.771 1.458,1.552 false 3.51,2.51 3.917,2.292 false 5.573,1.677 5.99,1.823 false 1.146,0.698 1.333,0.917 0.188,0.219 10 true A 0.719,0.698 1.021,0.99 0.302,0.292 10 false A 3.792,0.469 3.948,0.667 0.156,0.198 10 true B 3.792,0.906 4.094,1.167 0.302,0.26 10 false B 5.688,0.698 5.854,0.917 0.167,0.219 10 true C 6.104,0.698 6.406,1 0.302,0.302 10 false C 0.823,1.177 1.385,1.469 0.563,0.292 10 false A-A 2.979,1.115 3.375,1.385 0.396,0.271 10 false B-B 5.844,1.188 6.313,1.417 0.469,0.229 10 false C-C 1.365,1.76 1.573,1.948 0.208,0.188 10 false *a 3.74,2.49 4,2.75 0.26,0.26 10 false *a 6.26,1.75 6.469,1.938 0.208,0.188 10 false *a 3.969,2.167 4.188,2.385 0.219,0.219 10 false *b 5.333,1.573 5.583,1.813 0.25,0.24 10 false *b 1.51,1.438 1.917,1.729 0.406,0.292 10 false *b

Text in Illustration
*a 3.0 mm (0.118 in.) *b Edge of Curved Surface


b.

Remove the release paper and application tape from the rear roof stripe.


Hide 75552H 4.INSTALL ROOF DRIP SIDE MOULDING LH

Hide 75551H 5.INSTALL ROOF DRIP SIDE MOULDING RH

HINT:

Use the same procedure described for the LH side.


Hide 81570 6.INSTALL CENTER STOP LIGHT ASSEMBLY

Hide 75655 7.INSTALL CENTER PILLAR TAPE

HINT:

When installing the center pillar tape, heat the vehicle body and center pillar tape using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
Center Pillar Tape 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not heat the vehicle body or center pillar tape excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B466132E01
1.99,1.448 2.292,1.667 true 2.917,0.49 3.052,0.917 true 1.063,1.865 1.188,1.99 true 0.229,0.406 0.458,0.646 0.229,0.24 10 false A 0.417,0.5 0.656,0.75 0.24,0.25 10 false A 0.938,1.094 1.365,1.333 0.427,0.24 10 false A-A 0.854,0.115 1.083,0.354 0.229,0.24 10 false B 0.854,0.677 1.125,0.896 0.271,0.219 10 false B 2.646,0.052 3.052,0.292 0.406,0.24 10 false B-B 3.052,0.104 3.292,0.302 0.24,0.198 10 false *a 0.531,1.74 0.771,1.938 0.24,0.198 10 false *a 2.26,1.948 2.5,2.146 0.24,0.198 10 false *b 1.229,1.948 1.469,2.146 0.24,0.198 10 false *c 1.875,1.26 2.115,1.458 0.24,0.198 10 false *a 3.063,0.938 3.302,1.135 0.24,0.198 10 false *c

Refer to the illustration to position a new center pillar tape.

Text in Illustration
*a 3.0 mm (0.118 in.)
*b 2.0 mm (0.079 in.)
*c Edge of Curved Surface


b.

Remove the release paper and application tape from the center pillar tape.


Hide 62109A 8.INSTALL SIDE LOWER WINDOW GLASS SUB-ASSEMBLY LH

Hide 62720C 9.INSTALL SIDE FRONT WINDOW GLASS SUB-ASSEMBLY LH

Hide 75911B 10.INSTALL BLACK OUT HOOD TAPE

HINT:

When installing the black out hood tape, heat the vehicle body and black out hood tape using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
Black Out Hood Tape 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not heat the vehicle body or black out hood tape excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

Refer to the illustration to position a new black out hood tape.

B466093E01
2.542,2.229 2.646,2.271 2.646,2.271 2.802,2.094 true 1.031,0.75 1.354,0.563 false 0.594,0.083 1.073,0.323 0.479,0.24 10 false A-A 0.583,2.135 1.031,2.458 0.448,0.323 10 false B-B 2.073,1.688 2.479,1.958 0.406,0.271 10 false C-C 4.156,1.802 4.521,2.042 0.365,0.24 10 false D-D 5.51,1.729 5.979,1.979 0.469,0.25 10 false E-E 6.229,0.156 6.656,0.469 0.427,0.313 10 false F-F 3.583,0.052 3.854,0.281 0.271,0.229 10 false A 3.573,0.583 3.844,0.802 0.271,0.219 10 false A 3.583,0.917 3.75,1.083 0.167,0.167 10 false B 3.552,1.281 3.698,1.5 0.146,0.219 10 true B 4.427,0.115 4.792,0.365 0.365,0.25 10 false C 4.438,0.479 4.771,0.771 0.333,0.292 10 false C 1.823,0.49 2.167,0.771 0.344,0.281 10 false D 2.292,0.49 2.594,0.75 0.302,0.26 10 false D 2.094,1.021 2.219,1.229 0.125,0.208 10 true E 2.125,1.396 2.208,1.583 0.083,0.188 10 true E 3.167,1.094 3.323,1.281 0.156,0.188 10 false F 3.125,1.438 3.281,1.625 0.156,0.188 10 false F 0.24,0.365 0.552,0.604 0.313,0.24 10 false *a 0.865,1.656 1.167,1.958 0.302,0.302 10 false *a 1.25,0.74 1.542,0.979 0.292,0.24 10 false *b 0.958,2.833 1.271,3.094 0.313,0.26 10 false *b 2.76,2.281 3.063,2.583 0.302,0.302 10 false *b 4.146,2.583 4.396,2.823 0.25,0.24 10 false *b 6.313,3.063 6.563,3.292 0.25,0.229 10 false *b 2.802,1.969 3.104,2.25 0.302,0.281 10 false *e 1.906,2 2.24,2.271 0.333,0.271 10 false *c 1.479,2.135 1.771,2.365 0.292,0.229 10 false *d 1.365,0.417 1.625,0.688 0.26,0.271 10 false *e 1.083,2.365 1.344,2.677 0.26,0.313 10 false *e 4.896,2.615 5.167,2.833 0.271,0.219 10 false *e 6.333,2.51 6.635,2.729 0.302,0.219 10 false *e 6.917,0.469 7.125,0.729 0.208,0.26 10 false *e

Text in Illustration
*a 4.0 mm (0.157 in.) *b 3.0 mm (0.118 in.)
*c 3.5 mm (0.138 in.) *d 9.5 mm (0.374 in.)
*g Edge of Curved Surface - -


b.

Remove the release paper and application tape from the black out hood tape.


c.

Apply the tab tape to the position shown in the illustration.

B466094E01
5.333,1.958 5.594,2.042 false 3.219,2.552 3.708,2.229 3.708,2.229 3.969,2.854 false 1.99,2.302 2.188,2.052 false 5.531,0.719 5.75,0.896 false 2.198,1.896 2.396,2.073 0.198,0.177 10 false *a 5.156,1.813 5.438,2.104 0.281,0.292 10 false *a 3.656,2.042 3.958,2.271 0.302,0.229 10 false *a 5.354,0.604 5.635,0.823 0.281,0.219 10 false *a

Text in Illustration
*a Tab Tape - -

HINT:

Apply so that it does not protrude onto the panel surface.



Hide 56111 11.INSTALL WINDSHIELD GLASS

Hide 75914B 12.INSTALL BLACK OUT FENDER TAPE LH

HINT:

When installing the black out fender tape LH, heat the vehicle body and black out fender tape LH using a heat light.


Standard
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
Black Out Fender Tape LH 20 to 30 °C (68 to 86 °F)

NOTICE:
·

Do not heat the vehicle body or black out fender tape LH excessively.

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.
B467510E01
2.427,4.083 2.708,4.177 false 2.885,0.406 3.083,0.281 false 0.854,4.031 1.135,4.031 false 2.49,0.333 2.781,0.583 0.292,0.25 10 false *b 0.646,0.177 1.083,0.406 0.438,0.229 10 false B-B 2.417,0.073 2.781,0.292 0.365,0.219 10 false A-A 2.771,2.948 3.167,3.24 0.396,0.292 10 false D-D 0.531,3.552 0.99,3.813 0.458,0.26 10 false C-C 0.875,0.979 1.094,1.156 0.219,0.177 10 false *a 3.115,0.188 3.333,0.365 0.219,0.177 10 false *c 2.26,3.958 2.479,4.135 0.219,0.177 10 false *d 1.188,3.948 1.5,4.229 0.313,0.281 10 false *d 1.708,2.469 1.979,2.688 0.271,0.219 10 false A 2,2.479 2.271,2.75 0.271,0.271 10 false A 1.052,2.365 1.271,2.573 0.219,0.208 10 false B 1.354,3.031 1.615,3.24 0.26,0.208 10 false D 1.281,1.365 1.5,1.594 0.219,0.229 10 false C 1.271,1.646 1.427,1.823 0.156,0.177 10 true C 1.344,2.365 1.542,2.552 0.198,0.188 10 true B 1.354,3.313 1.479,3.5 0.125,0.188 10 true D

Refer to the illustration to position a new black out fender tape LH.

Text in Illustration
*a 6.7 mm (0.263 in.)
*b 0 mm (0 in.)
*c Edge of Curved Surface
*d Front Pillar End Cover LH


b.

Remove the release paper and application from the black out fender tape LH.


Hide 75913B 13.INSTALL BLACK OUT FENDER TAPE RH

HINT:

Use the same procedure described for the LH side.


Hide 61196D 14.INSTALL FRONT PILLAR END COVER LH

Hide 61195E 15.INSTALL FRONT PILLAR END COVER RH

Hide 53181A 17.INSTALL HEADLIGHT COVER RH

HINT:

Use the same procedure described for the LH side.