Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM U

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the ignition switch off before measuring the resistances between CAN main wires and between CAN branch wires.

·

Turn the ignition switch off before inspecting CAN wires for a ground short.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



JUNCTION CONNECTOR


a.
C358902E01
1.479,0.073 1.885,0.344 0.406,0.271 1.573,0.958 1.354,0.49 1.354,0.49 1.208,0.49 true 1.344,0.948 1.042,0.708 1.042,0.708 0.917,0.708 true 1.365,1.26 1.073,1.625 1.073,1.625 0.938,1.625 true 1.656,1.281 1.396,1.927 1.396,1.927 1.24,1.927 true 1.771,1.271 1.99,1.917 1.99,1.917 2.188,1.917 true 2.042,1.281 2.354,1.573 2.354,1.573 2.521,1.573 true 2.042,0.938 2.229,0.688 2.229,0.688 2.385,0.688 true 1.844,0.938 2,0.469 2,0.469 2.146,0.469 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.552,0.115 1.865,0.313 0.313,0.198 10 false A91 0.646,0.417 1.323,0.615 0.677,0.198 10 false CANH*c 0.313,0.625 0.99,0.823 0.677,0.198 10 false CANH*b 0.354,1.552 1.031,1.75 0.677,0.198 10 false CANH*d 0.656,1.844 1.333,2.042 0.677,0.198 10 false CANH*e 2.271,1.844 3.188,2.042 0.917,0.198 10 false CANL*d 2.594,1.49 3.25,1.677 0.656,0.188 10 false CANL*e 2.479,0.625 3.135,0.813 0.656,0.188 10 false CANL*c 2.198,0.385 2.844,0.542 0.646,0.156 10 false CANL*b

NO. 3 CAN JUNCTION CONNECTOR

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b
·

for No. 63 Junction Connector (for LHD)

·

for No. 67 Junction Connector (for RHD)


*c for Brake Actuator Assembly (Skid Control ECU)
*d for Airbag ECU Assembly (w/ Airbag System)
*e for No. 3 Junction Connector (w/o Airbag System)

Terminal No. (Symbol) Wiring Color Connect to

*1: for LHD

*2: for RHD

*3: w/ Airbag System

*4: w/o Airbag System

A91-1 (CANH) B
·

No. 63 junction connector*1

·

No. 67 junction connector*2


A91-3 (CANL) W
A91-2 (CANH) P Brake actuator assembly (skid control ECU)
A91-4 (CANL) V
A91-5 (CANH) B Airbag ECU assembly*3
A91-7 (CANL) W
A91-6 (CANH) B No. 3 junction connector*4
A91-8 (CANL) W


b.
C358905E02
0.208,0.969 0.573,1.229 0.365,0.26 1.427,1.063 0.969,0.49 0.969,0.49 0.833,0.49 true 1.552,1.052 1.104,0.313 1.104,0.313 0.958,0.313 true 1.708,1.052 1.333,0.146 1.333,0.146 1.198,0.146 true 2.115,1.042 2.115,0.229 2.115,0.229 2.271,0.229 true 2.271,1.063 2.271,0.438 2.271,0.438 2.427,0.438 true 2.406,1.073 2.573,0.635 2.573,0.635 2.719,0.635 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.26,1.01 0.573,1.208 0.313,0.198 10 false A80 0.281,0.417 0.865,0.604 0.583,0.188 10 false CANL*b 0.417,0.219 1,0.406 0.583,0.188 10 false CANL*c 0.656,0.042 1.24,0.229 0.583,0.188 10 false CANL*d 2.333,0.135 2.917,0.323 0.583,0.188 10 false CANH*b 2.49,0.365 3.073,0.552 0.583,0.188 10 false CANH*c 2.781,0.563 3.365,0.75 0.583,0.188 10 false CANH*d

NO. 3 JUNCTION CONNECTOR (w/o Airbag System)

Text in Illustration
*a Front view of wire harness connector
(to No. 3 Junction Connector)
*b for No. 3 CAN Junction Connector
*c for Yaw Rate Sensor
*d for No. 1 CAN Junction Terminal

Terminal No. (Symbol) Wiring Color Connect to
A80-9 (CANH) B No. 3 CAN junction connector
A80-4 (CANL) W
A80-10 (CANH) R Yaw rate sensor
A80-5 (CANL) G
A80-11 (CANH) B No. 1 CAN junction terminal
A80-6 (CANL) W


c.
C358905E03
0.198,0.938 0.573,1.198 0.375,0.26 2.125,1.042 2.115,0.458 2.115,0.458 2.281,0.458 true 1.563,1.042 1.552,0.448 1.552,0.448 1.417,0.448 true 1.698,1.052 1.698,0.208 1.698,0.208 1.552,0.208 true 1.969,1.052 1.969,0.219 1.969,0.219 2.104,0.219 true 0.271,0.969 0.729,1.167 0.458,0.198 10 false J86 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1,0.115 1.917,0.313 0.917,0.198 10 false CANL*c 0.875,0.354 1.792,0.552 0.917,0.198 10 false CANL*b 2.167,0.125 3.083,0.323 0.917,0.198 10 false CANH*b 2.354,0.385 3.271,0.583 0.917,0.198 10 false CANH*c

NO. 59 JUNCTION CONNECTOR (for LHD)

Text in Illustration
*a Front view of wire harness connector
(to No. 59 Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Combination Meter Assembly

Terminal No. (Symbol) Wiring Color Connect to
J86-8 (CANH) Y Central gateway ECU (network gateway ECU)
J86-5 (CANL) L
J86-9 (CANH) B Combination meter assembly
J86-6 (CANL) W


d.
C358905E04
0.135,1 0.5,1.271 0.365,0.271 1,1.083 0.813,0.854 0.813,0.854 0.677,0.854 true 1.125,1.042 0.875,0.563 0.875,0.563 0.729,0.563 true 1.281,1.052 0.979,0.302 0.979,0.302 0.854,0.302 true 1.448,1.052 1.698,0.135 1.698,0.135 1.833,0.135 true 1.563,1.063 1.813,0.313 1.813,0.313 1.938,0.313 true 1.708,1.063 1.979,0.51 1.979,0.51 2.104,0.51 true 0.208,1.052 0.667,1.25 0.458,0.198 10 false J90 0.104,0.781 1.021,0.979 0.917,0.198 10 false CANH*b 0.167,0.49 1.083,0.688 0.917,0.198 10 false CANH*c 0.271,0.208 1.188,0.406 0.917,0.198 10 false CANH*d 1.896,0.052 2.813,0.25 0.917,0.198 10 false CANL*b 2.01,0.25 2.927,0.448 0.917,0.198 10 false CANL*c 2.177,0.427 3.094,0.625 0.917,0.198 10 false CANL*d 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a

NO. 63 JUNCTION CONNECTOR (for LHD)

Text in Illustration
*a Front view of wire harness connector
(to No. 63 Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*d for No. 3 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
J90-1 (CANH) GR Central gateway ECU (network gateway ECU)
J90-4 (CANL) BE
J90-2 (CANH) R Spiral with sensor cable sub-assembly (steering angle sensor)
J90-5 (CANL) G
J90-3 (CANH) B No. 3 CAN junction connector
J90-6 (CANL) W


e.
C358905E05
1.5,0.146 1.865,0.396 0.365,0.25 1,1.073 0.813,0.5 0.813,0.5 0.656,0.5 true 1.281,1.042 1.281,0.292 1.281,0.292 1.135,0.292 true 1,1.323 0.885,1.76 0.885,1.76 0.729,1.76 true 1.302,1.333 1.302,2 1.302,2 1.146,2 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.563,0.188 2.021,0.385 0.458,0.198 10 false A85 0.552,0.219 1.469,0.417 0.917,0.198 10 false CANH*c 0.083,0.438 1,0.635 0.917,0.198 10 false CANH*b 0.156,1.688 1.073,1.885 0.917,0.198 10 false CANL*b 0.573,1.917 1.49,2.115 0.917,0.198 10 false CANL*c

NO. 66 JUNCTION CONNECTOR

Text in Illustration
*a Front view of wire harness connector
(to No. 66 Junction Connector)
*b for ECM
*c for Central Gateway ECU (Network Gateway ECU)

Terminal No. (Symbol) Wiring Color Connect to
A85-1 (CANH) V ECM
A85-12 (CANL) W
A85-3 (CANH) B Central gateway ECU (network gateway ECU)
A85-14 (CANL) W


f.
C358905E06
0.208,0.917 0.563,1.229 0.354,0.313 1.854,1.063 2.125,0.49 2.125,0.49 2.313,0.49 true 1.698,1.073 2.052,0.219 2.052,0.219 2.25,0.219 false 1.573,1.073 1.302,0.333 1.302,0.333 1.125,0.333 true 1.573,1.323 1.448,1.875 1.448,1.875 1.292,1.875 true 1.729,1.323 1.875,1.896 1.875,1.896 2.042,1.896 true 1.854,1.323 1.969,1.667 1.969,1.667 2.125,1.667 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 0.271,0.979 0.729,1.177 0.458,0.198 10 false J81 0.531,0.271 1.448,0.469 0.917,0.198 10 false CANH*b 2.313,0.146 3.229,0.344 0.917,0.198 10 false CANH*c 2.396,0.417 3.313,0.615 0.917,0.198 10 false CANH*d 0.698,1.792 1.615,1.99 0.917,0.198 10 false CANL*b 2.198,1.594 3.115,1.792 0.917,0.198 10 false CANL*d 2.104,1.813 3.021,2.01 0.917,0.198 10 false CANL*c

NO. 67 JUNCTION CONNECTOR (for RHD)

Text in Illustration
*a Front view of wire harness connector
(to No. 67 Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*d for No. 3 CAN Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
J81-5 (CANH) GR Central gateway ECU (network gateway ECU)
J81-16 (CANL) BE
J81-6 (CANH) R Spiral with sensor cable sub-assembly (steering angle sensor)
J81-17 (CANL) G
J81-7 (CANH) B No. 3 CAN junction connector
J81-18 (CANL) W


g.
C358905E07
0.229,1.052 0.573,1.354 0.344,0.302 1.573,1.063 1.396,0.417 1.396,0.417 1.229,0.417 true 1.688,1.083 1.802,0.438 1.802,0.438 1.948,0.438 true 1.719,1.302 2,1.823 2,1.823 2.146,1.823 true 1.594,1.302 1.427,1.823 1.427,1.823 1.24,1.823 true 0.292,1.115 0.75,1.313 0.458,0.198 10 false J76 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.646,0.333 1.281,0.552 0.635,0.219 10 false CANH*b 2.031,0.354 2.667,0.573 0.635,0.219 10 false CANH*c 2.219,1.76 2.854,1.979 0.635,0.219 10 false CANL*c 0.698,1.74 1.333,1.958 0.635,0.219 10 false CANL*b

NO. 68 JUNCTION CONNECTOR (for RHD)

Text in Illustration
*a Front view of wire harness connector
(to No. 68 Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Combination Meter Assembly

Terminal No. (Symbol) Wiring Color Connect to
J76-5 (CANH) Y Central gateway ECU (network gateway ECU)
J76-16 (CANL) L
J76-6 (CANH) B Combination meter assembly
J76-17 (CANL) W


h.
C300866E19
0.271,0.74 0.667,1.031 0.396,0.292 1.333,0.708 1.135,0.406 1.135,0.406 0.979,0.406 true 1.667,0.688 1.448,0.167 1.448,0.167 1.26,0.167 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.385,0.354 1.302,0.552 0.917,0.198 10 false CANH*b 0.688,0.094 1.604,0.292 0.917,0.198 10 false CANL*b 0.333,0.792 0.792,0.99 0.458,0.198 10 false A76

NO. 1 CAN JUNCTION TERMINAL (w/o Airbag System)

Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)
*b for No. 3 Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
A76-3 (CANH) B No. 3 junction connector
A76-2 (CANL) W



CHECK DLC3


a.
C253362E42
1.479,0.115 1.854,0.406 0.375,0.292 1.583,0.917 1.365,0.417 1.365,0.417 1.198,0.417 false 1.948,0.896 2.073,0.438 2.073,0.438 2.25,0.438 false 1.948,1.479 1.875,1.875 1.875,1.875 1.719,1.875 false 2.313,1.469 2.438,1.885 2.438,1.885 2.635,1.885 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.552,0.156 2.01,0.354 0.458,0.198 10 false J45 0.917,0.333 1.229,0.531 0.313,0.198 10 false CG 2.333,0.365 2.823,0.583 0.49,0.219 10 false CANH 1.313,1.802 1.813,2.01 0.5,0.208 10 false CANL 2.74,1.802 3.146,2 0.406,0.198 10 false BAT

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION.)


Text in Illustration
*a Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J45-6 (CANH) - J45-14 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
J45-6 (CANH) - J45-4 (CG) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J45-14 (CANL) - J45-4 (CG) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J45-6 (CANH) - J45-16 (BAT) P - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J45-14 (CANL) - J45-16 (BAT) V - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C331365E17
1.292,1.365 1.667,1.635 0.375,0.271 2.938,1.333 2.51,0.896 2.51,0.896 2.365,0.896 true 3.177,1.333 2.927,0.635 2.927,0.635 2.76,0.635 true 3.271,1.333 3.396,0.354 3.396,0.354 3.25,0.354 true 3.833,1.448 3.688,0.365 3.688,0.365 3.844,0.365 true 3.875,1.333 4.156,0.656 4.156,0.656 4.302,0.656 true 4.198,1.354 4.542,0.938 4.542,0.938 4.698,0.938 true 4.229,1.979 4.083,1.979 4.083,1.979 3.771,1.438 true 4.188,2.292 4.021,2.292 4.021,2.292 3.698,1.458 true 3.104,2.302 3.292,2.302 3.292,2.302 3.615,1.448 true 3.073,1.969 3.219,1.969 3.219,1.969 3.521,1.448 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.688,0.281 3.604,0.479 0.917,0.198 10 false CA2H*C 2.198,0.563 3.115,0.76 0.917,0.198 10 false CA2L*C 2.01,0.813 2.927,1.01 0.917,0.198 10 false GND 3.906,0.292 4.823,0.49 0.917,0.198 10 false CA6H*A 4.375,0.583 5.292,0.781 0.917,0.198 10 false CA6L*A 4.781,0.865 5.698,1.063 0.917,0.198 10 false BATT 4.302,1.906 5.219,2.104 0.917,0.198 10 false CA5H*D 4.281,2.219 5.198,2.417 0.917,0.198 10 false CA5L*D 2.542,2.219 3.458,2.417 0.917,0.198 10 false CA4L*B 2.51,1.896 3.427,2.094 0.917,0.198 10 false CA4H*B 1.375,1.406 1.833,1.604 0.458,0.198 10 false J51

Text in Illustration
*A V Bus *B Bus 2
*C Bus 4 *D Bus 5
*a Component without harness connected
(Central Gateway ECU [Network Gateway ECU])
- -

a.
C326490E89
1.458,0.146 1.802,0.385 0.344,0.24 0.396,1.76 0.219,1.76 0.219,1.76 0.448,0.979 true 1,1.99 1.146,1.99 1.146,1.99 1.375,1.208 true 1.417,2.063 1.281,2.063 1.281,2.063 1.51,1.208 true 1.958,1.896 1.792,1.896 1.792,1.896 1.656,1.219 true 2.448,1.771 2.302,1.771 2.302,1.771 1.802,1.208 true 0.729,0.406 0.854,0.406 0.854,0.406 1.115,0.938 true 0.938,0.177 1.083,0.177 1.083,0.177 1.26,1.135 true 2.167,0.115 1.99,0.115 1.99,0.115 2.292,1.125 true 2.427,0.281 2.271,0.281 2.271,0.281 2.438,0.938 true 2.896,0.448 2.771,0.448 2.771,0.448 2.927,0.917 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 0.396,0.104 1.313,0.302 0.917,0.198 10 false CA6H*A 0.177,0.323 1.094,0.521 0.917,0.198 10 false CA6L*A 0.458,1.677 1.375,1.875 0.917,0.198 10 false BATT 0.427,1.906 1.344,2.104 0.917,0.198 10 false CA5H*D 1.458,1.979 2.375,2.177 0.917,0.198 10 false CA5L*D 2.021,1.813 2.938,2.01 0.917,0.198 10 false CA4L*B 2.51,1.688 3.427,1.885 0.917,0.198 10 false CA4H*B 2.208,0.042 3.125,0.24 0.917,0.198 10 false CA2H*C 2.479,0.208 3.146,0.396 0.667,0.188 10 false CA2L*C 2.938,0.375 3.365,0.573 0.427,0.198 10 false GND 1.531,0.177 1.99,0.375 0.458,0.198 10 false J51

Disconnect the central gateway ECU (network gateway ECU) connector.

Text in Illustration
*A V Bus
*B Bus 2
*C Bus 4
*D Bus 5
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


b.

Measure the resistance according to the value(s) in the table below.

V Bus Branch Lines (DLC3 - Central gateway ECU [network gateway ECU])
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J51-14 (CA6H) - J51-5 (CA6L) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
J51-14 (CA6H) - J51-10 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-5 (CA6L) - J51-10 (GND) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-14 (CA6H) - J51-1 (BATT) P - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-5 (CA6L) - J51-1 (BATT) V - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J51-18 (CA4H) - J51-17 (CA4L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
J51-18 (CA4H) - J51-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-17 (CA4L) - J51-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-18 (CA4H) - J51-1 (BATT) B - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-17 (CA4L) - J51-1 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J51-22 (CA2H) - J51-7 (CA2L) GR - BE HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
J51-22 (CA2H) - J51-10 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-7 (CA2L) - J51-10 (GND) BE - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-22 (CA2H) - J51-1 (BATT) GR - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-7 (CA2L) - J51-1 (BATT) BE - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J51-15 (CA5H) - J51-16 (CA5L) Y - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
J51-15 (CA5H) - J51-10 (GND) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-16 (CA5L) - J51-10 (GND) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J51-15 (CA5H) - J51-1 (BATT) Y - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J51-16 (CA5L) - J51-1 (BATT) L - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for 2TR-FE)


Refer to Terminals of ECU (Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM).

a.
C371312E01
1.458,0.167 1.885,0.458 0.427,0.292 1.406,2.344 1.833,2.635 0.427,0.292 1.479,0.938 0.885,0.323 0.885,0.323 0.698,0.323 true 1.635,1.427 1.448,2.031 1.448,2.031 1.271,2.031 true 2.125,3.792 2.125,4.406 2.125,4.406 1.979,4.406 true 2.271,3.792 2.271,4.406 2.271,4.406 2.469,4.406 true 1.01,1.958 1.625,2.156 0.615,0.198 10 false EC 0.323,0.26 0.938,0.458 0.615,0.198 10 false BATT 0.094,0.063 0.708,0.26 0.615,0.198 10 false *a 1.552,4.333 2.167,4.531 0.615,0.198 10 false CANH 2.552,4.323 3.167,4.521 0.615,0.198 10 false CANL 1.49,2.406 2.104,2.604 0.615,0.198 10 false A53 1.552,0.219 2.167,0.417 0.615,0.198 10 false A55

Disconnect the ECM connectors.

Text in Illustration
*a Front view of wire harness connector
(to ECM)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A53-33 (CANH) - A53-34 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A53-33 (CANH) - A55-22 (EC) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A53-34 (CANL) - A55-22 (EC) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A53-33 (CANH) - A55-3 (BATT) V - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A53-34 (CANL) - A55-3 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for N04C-UH)


Refer to Terminals of ECU (Click HereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM).

a.

Disconnect the ECM connectors.

C371329E01
2.188,0.292 2.583,0.573 0.396,0.281 4.885,0.302 5.281,0.583 0.396,0.281 2.146,1.208 1.979,0.542 1.979,0.542 1.802,0.542 true 5.708,1.198 5.906,0.594 5.906,0.594 6.094,0.594 true 1.813,1.594 1.594,1.479 1.594,1.479 1.427,1.479 true 1.823,1.813 1.74,2.115 1.74,2.115 1.583,2.115 true 2.26,0.354 2.719,0.552 0.458,0.198 10 false A52 4.958,0.365 5.417,0.563 0.458,0.198 10 false B60 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.406,0.469 2.021,0.667 0.615,0.198 10 false BATT 0.99,1.406 1.604,1.604 0.615,0.198 10 false CANH 1.177,2.042 1.792,2.24 0.615,0.198 10 false CANL 6.167,0.521 6.781,0.719 0.615,0.198 10 false E1

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A52-17 (CANH) - A52-28 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A52-17 (CANH) - B60-7 (E1) V - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A52-28 (CANL) - B60-7 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A52-17 (CANH) - A52-2 (BATT) V - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A52-28 (CANL) - A52-2 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM (for N04C-VQ, N04C-VL)


Refer to Terminals of ECU.

for N04C-VQ: Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

for N04C-VL: Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

a.

Disconnect the ECM connectors.

C371313E01
1.167,0.333 1.542,0.604 0.375,0.271 3.438,0.333 3.813,0.604 0.375,0.271 5.396,0.354 5.823,0.635 0.427,0.281 0.542,1.188 0.688,1.188 0.688,1.188 1.021,1.313 true 0.542,1.521 0.698,1.521 0.698,1.521 1.021,1.427 true 3.427,2.354 3.594,2.354 3.594,2.354 3.813,1.885 true 4.688,1.177 4.833,1.177 4.833,1.177 5.083,1.26 true 0.125,1.115 0.74,1.313 0.615,0.198 10 false CANL 0.104,1.438 0.719,1.635 0.615,0.198 10 false CANH 3.031,2.281 3.646,2.479 0.615,0.198 10 false BATT 4.448,1.104 5.063,1.302 0.615,0.198 10 false E1 1.229,0.396 1.688,0.594 0.458,0.198 10 false A56 3.51,0.385 3.969,0.583 0.458,0.198 10 false A57 5.458,0.417 5.917,0.615 0.458,0.198 10 false B102 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A56-7 (CANH) - A56-1 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A56-7 (CANH) - B102-1 (E1) V - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A56-1 (CANL) - B102-1 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A56-7 (CANH) - A57-23 (BATT) V - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A56-1 (CANL) - A57-23 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TERMINALS OF ECU).

a.
C358900E01
1.458,0.073 1.844,0.323 0.385,0.25 0.719,0.875 0.719,0.177 0.719,0.177 0.854,0.177 true 2.083,0.813 2.146,0.146 2.146,0.146 2.302,0.146 true 2.104,1.01 2.417,0.333 2.417,0.333 2.563,0.333 true 2.656,1 2.458,1.99 2.458,1.99 2.333,1.99 true 0.906,0.115 1.521,0.313 0.615,0.198 10 false GND2 1.521,0.104 2.135,0.302 0.615,0.198 10 false A71 2.375,0.063 2.99,0.26 0.615,0.198 10 false CANL 2.615,0.25 3.229,0.448 0.615,0.198 10 false CANH 2.052,1.906 2.667,2.104 0.615,0.198 10 false BM 0.063,0.083 0.677,0.281 0.615,0.198 10 false *a

Disconnect the brake actuator assembly (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A71-22 (CANH) - A71-10 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A71-22 (CANH) - A71-1 (GND2) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A71-10 (CANL) - A71-1 (GND2) V - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A71-22 (CANH) - A71-13 (BM) P - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A71-10 (CANL) - A71-13 (BM) V - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG ECU ASSEMBLY (w/ Airbag System)


Refer to Terminals of ECU (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>TERMINALS OF ECU).

a.
C227529E24
0.323,0.896 0.708,1.156 0.385,0.26 0.365,2.573 0.75,2.833 0.385,0.26 1.302,1.802 1.448,1.802 1.448,1.802 1.771,1.333 true 2.417,1.646 2.26,1.646 2.26,1.646 2.104,1.333 true 2.51,3.188 2.354,3.188 2.354,3.188 2.198,2.875 true 2.583,0.542 2.417,0.542 2.417,0.542 2,0.99 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.385,0.938 0.771,1.146 0.385,0.208 10 false A58 0.448,2.625 0.833,2.833 0.385,0.208 10 false J45 0.167,1.854 0.479,2.052 0.313,0.198 10 false *b 2.646,0.469 3.26,0.667 0.615,0.198 10 false CANH 2.5,1.573 3.115,1.771 0.615,0.198 10 false CANL 1.052,1.729 1.667,1.927 0.615,0.198 10 false E1 2.573,3.115 3.188,3.313 0.615,0.198 10 false BAT

Disconnect the airbag ECU assembly connector (Click HereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>PRECAUTION).

Text in Illustration
*a Rear view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-13 (CANH) - A58-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A58-13 (CANH) - A58-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A58-22 (CANL) - A58-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A58-13 (CANH) - J45-16 (BAT) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A58-22 (CANL) - J45-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C371297E01
0.448,0.552 0.813,0.854 0.365,0.302 1.219,1.188 1.375,1.188 1.375,1.188 1.375,0.885 true 1.354,1.438 1.49,1.438 1.49,1.438 1.49,0.906 true 1.854,1.427 1.729,1.427 1.729,1.427 1.729,0.906 true 1.99,1.198 1.854,1.198 1.854,1.198 1.854,0.896 true 0.25,0.167 0.563,0.365 0.313,0.198 10 false *a 0.51,0.615 0.969,0.813 0.458,0.198 10 false J71 0.917,1.094 1.375,1.292 0.458,0.198 10 false BAT 0.927,1.354 1.385,1.552 0.458,0.198 10 false CANH 2.063,1.115 2.521,1.313 0.458,0.198 10 false ESS 1.917,1.344 2.375,1.542 0.458,0.198 10 false CANL

Text in Illustration
*a Component without harness connected
(Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])

a.
C358904E01
1.479,0.271 1.813,0.51 0.333,0.24 1.135,1.646 1.281,1.646 1.281,1.646 1.469,1.323 true 2.604,1.615 2.438,1.615 2.438,1.615 2.177,1.292 true 1.458,1.854 1.625,1.854 1.625,1.854 1.625,1.302 false 2,1.865 1.802,1.865 1.802,1.865 1.802,1.292 true 1.542,0.302 2,0.5 0.458,0.198 10 false J71 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.792,1.573 1.25,1.771 0.458,0.198 10 false ESS 1.083,1.781 1.542,1.979 0.458,0.198 10 false CANL 2.063,1.781 2.521,1.979 0.458,0.198 10 false CANH 2.667,1.531 3.125,1.729 0.458,0.198 10 false BAT

Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.

Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J71-4 (CANH) - J71-3 (CANL) R -G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
J71-4 (CANH) - J71-2 (ESS) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J71-3 (CANL) - J71-2 (ESS) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J71-4 (CANH) - J71-6 (BAT) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J71-3 (CANL) - J71-6 (BAT) G - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK YAW RATE SENSOR (w/o Airbag System)


C210012E05
1.5,0.396 1.885,0.688 0.385,0.292 1.198,1.99 1.396,1.99 1.396,1.99 1.76,1.177 true 2.531,1.99 2.333,1.99 2.333,1.99 1.865,1.177 true 2.365,0.813 2.198,0.813 2.198,0.813 1.958,1.125 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.573,0.458 2.031,0.656 0.458,0.198 10 false A72 2.448,0.729 2.906,0.927 0.458,0.198 10 false GND 2.604,1.906 3.219,2.104 0.615,0.198 10 false CANL 0.76,1.917 1.375,2.115 0.615,0.198 10 false CANH

Text in Illustration
*a Component without harness connected
(Yaw Rate Sensor)

a.
C371319E01
1.469,0.042 1.875,0.313 0.406,0.271 1.51,1.75 1.917,2.021 0.406,0.271 1.344,1.406 1.51,1.406 1.51,1.406 1.5,0.885 true 1.823,1.417 1.646,1.417 1.646,1.417 1.635,0.896 false 0.74,1.177 0.927,1.177 0.927,1.177 1.344,0.896 true 2.573,3.083 2.375,3.083 2.375,3.083 2.24,2.781 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 0.229,1.885 0.542,2.083 0.313,0.198 10 false *b 1.604,1.802 2.063,2 0.458,0.198 10 false J45 1.542,0.083 2,0.281 0.458,0.198 10 false A72 0.375,1.094 0.99,1.292 0.615,0.198 10 false GND 0.948,1.333 1.563,1.531 0.615,0.198 10 false CANL 1.917,1.344 2.531,1.542 0.615,0.198 10 false CANH 2.635,3.01 3.25,3.208 0.615,0.198 10 false BAT

Disconnect the yaw rate sensor connector.

Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A72-3 (CANH) - A72-2 (CANL) R - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A72-3 (CANH) - A72-1 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-2 (CANL) - A72-1 (GND) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-3 (CANH) - J45-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A72-2 (CANL) - J45-16 (BAT) G - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


Refer to Terminals of ECU (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU).

a.
C358908E01
1.49,0.25 1.865,0.51 0.375,0.26 0.656,1.063 0.656,0.5 0.656,0.5 0.49,0.5 true 0.667,1.271 0.667,1.969 0.667,1.969 0.802,1.969 true 0.792,1.271 0.792,1.771 0.792,1.771 0.938,1.771 true 0.906,1.292 0.906,1.583 0.906,1.583 1.042,1.583 true 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 1.604,0.302 1.917,0.5 0.313,0.198 10 false J1 0.323,0.427 0.938,0.625 0.615,0.198 10 false B 1.104,1.5 1.719,1.698 0.615,0.198 10 false CANH 0.99,1.688 1.604,1.885 0.615,0.198 10 false CANL 0.833,1.885 1.448,2.083 0.615,0.198 10 false ES

Disconnect the combination meter assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Terminal Description Specified Condition
J1-23 (CANH) - J1-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
J1-23 (CANH) - J1-21 (ES) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J1-22 (CANL) - J1-21 (ES) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J1-23 (CANH) - J1-1 (B) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J1-22 (CANL) - J1-1 (B) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher