Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1430  Brake Pedal Load Sensing Switch OFF Stuck Malfunction  C1431  Brake Pedal Load Sensing Switch ON Stuck Malfunction  


DESCRIPTION

The brake pedal load sensing switch signal is turned on when the brake pedal is depressed with force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.

DTC No. DTC Detection Condition Trouble Area
C1430 Any of the following is detected:
1.

With the stop light switch signal ON, the brake pedal load sensing switch signal OFF, and the master cylinder pressure 6 MPa or more, the deceleration is 0.4 G or more for 1 second or more.

2.

With the stop light switch signal ON, the brake pedal load sensing switch signal OFF, and the master cylinder pressure 6 MPa or more, the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.


·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)


C1431 Any of the following is detected:
1.

Immediately after ignition switch is turned to ON and with the stop light switch signal OFF, the brake pedal load sensing switch signal ON, the master cylinder pressure below 0.7 MPa (71.1 kgf/cm2, 101 psi), and the engine speed 500 rpm or higher, the deceleration is below 0.08 G for 10 seconds or more.

2.

The condition that the brake pedal load sensing switch signal remains ON while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (18 mph) occurs 5 times in succession.


·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When DTC C1425 and/or C1426 is output together with DTC C1430 and/or C1431, inspect and repair the trouble areas indicated by DTC C1425 and/or C1426 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425, or Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426).


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake with switch pedal sub-assembly) / ON or OFF ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-


f.

Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



g.

Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.

OK:

First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.



Result:
Result Proceed to
OK A
NG (Turning on of the brake pedal load sensing switch is not confirmed) B
NG (The brake pedal load sensing switch turns on first) C



A

2.RECONFIRM DTC

B

3.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

C

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform the road test.



Result:
Result Proceed to
DTCs C1430 and C1431 are not output A
DTCs C1430 and/or C1431 are output B



A

B

3.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY
a.

Inspect the brake pedal load sensing switch (brake pedal support assembly) (Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (w/ Brake pedal Load Sensing Switch)>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the H2 brake pedal load sensing switch (brake pedal support assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-23 (FSW+) - H2-2 (FSW+) Always Below 1 Ω
A71-23 (FSW+) or H2-2 (FSW+ ) - Body ground Always 10 kΩ or higher
H2-1 (FSW-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation (Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (w/ Brake pedal Load Sensing Switch)>INSTALLATION).

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY