Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1426  Stop Light Switch OFF Stuck Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.

DTC No. DTC Detection Condition Trouble Area
C1426 When the +BS terminal voltage is 9.5 V or more, the brake pedal load sensing switch signal is on, the master cylinder pressure is 2 MPa (20.4 kgf/cm2, 290 psi) or more and the deceleration calculated from the vehicle speed is 0.2 G or more, the stop light switch assembly is off for 2 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Skid control ECU (Brake actuator assembly)

·

STOP NO. 5 fuse

·

STOP NO. 1 fuse



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

b.

Check the stop light switch assembly installation (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSTALLATION).

OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and switch before inspecting the input signals and other related parts.



Result:
Proceed to
OK
NG



OK

2.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

2.CHECK STOP LIGHT OPERATION
a.

Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)

NG

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


d.

In accordance with the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake with switch pedal sub-assembly) / ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-


e.

Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



f.

Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch turn on.

OK:

First the stop light switch assembly should turn on, and then the brake pedal load sensing switch should turn on.



Result:
Result Proceed to
OK A
NG (The stop light switch assembly does not turn on.) B
NG (Turning on of the brake pedal load sensing switch is not confirmed.) C
NG (The brake pedal load sensing switch turns on first.) D



A

4.RECONFIRM DTC

B

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)

C

7.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

D

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1426 is not output A
DTC C1426 is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C399804E04
1.531,0.135 1.885,0.365 0.354,0.229 1.885,1.833 2.219,1.292 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.75,1.885 2.146,2.073 0.396,0.188 10 false STP 1.594,0.167 1.979,0.406 0.385,0.24 10 false A71

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A71-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C399804E02
1.531,0.135 1.885,0.365 0.354,0.229 0.958,1.813 0.698,1.24 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.823,1.896 1.344,2.156 0.521,0.26 10 false GND1 1.594,0.167 1.979,0.406 0.385,0.24 10 false A71

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-25 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

7.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY
a.

Inspect the brake pedal load sensing switch (brake with switch pedal sub-assembly) (Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (w/ Brake pedal Load Sensing Switch)>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the H2 brake pedal load sensing switch (brake pedal support assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-23 (FSW+) - H2-2 (FSW+) Always Below 1 Ω
A71-23 (FSW+) or H2-2 (FSW+ ) - Body ground Always 10 kΩ or higher
H2-1 (FSW-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSPECTION).

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

10.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

10.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C399804E04
1.531,0.135 1.885,0.365 0.354,0.229 1.885,1.833 2.219,1.292 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.75,1.885 2.146,2.073 0.396,0.188 10 false STP 1.594,0.167 1.979,0.406 0.385,0.24 10 false A71

Turn the ignition switch off.


b.

Reinstall the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSTALLATION).


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A71-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

11.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

11.RECONFIRM DTC
a.

Reconnect the A71 skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1426 is not output A
DTC C1426 is output B


HINT:

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (w/ Brake pedal Load Sensing Switch)>REMOVAL).




A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)