Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1426  Stop Light Switch OFF Stuck Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.

DTC No. DTC Detection Condition Trouble Area
C1426 When the IG1 terminal voltage is 9.5 V or more, the brake pedal load sensing switch is on, the master cylinder pressure is 2 MPa (20.4 kgf/cm2, 290 psi) or more and the deceleration calculated from the vehicle speed is 0.2 G or more, the stop light switch assembly is off for 2 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Skid control ECU (Brake actuator assembly)

·

STOP NO. 5 fuse

·

STOP NO. 1 fuse



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

b.

Check the stop light switch assembly installation (Click hereVehicle Interior>LIGHTING>STEP LIGHT ASSEMBLY>INSTALLATION).

OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and switch before inspecting the input signals and other related parts.



Result:
Proceed to
OK
NG



OK

2.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

2.CHECK STOP LIGHT OPERATION
a.

Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)

NG

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


d.

In accordance with the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake with switch pedal sub-assembly) / ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-


e.

Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



f.

Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch turn on.

OK:

First the stop light switch assembly should turn on, and then the brake pedal load sensing switch should turn on.



Result:
Result Proceed to
OK A
NG (The stop light switch assembly does not turn on.) B
NG (Turning on of the brake pedal load sensing switch is not confirmed.) C
NG (The brake pedal load sensing switch turns on first.) D



A

4.RECONFIRM DTC

B

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)

C

7.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

D

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1426 is not output A
DTC C1426 is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

5.CHECK TERMINAL VOLTAGE (STP TERMINAL)

OK

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

7.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

10.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

10.CHECK TERMINAL VOLTAGE (STP TERMINAL)

OK

11.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

11.RECONFIRM DTC
a.

Reconnect the A71 skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1426 is not output A
DTC C1426 is output B


HINT:

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (w/ Brake pedal Load Sensing Switch)>REMOVAL).




A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)