Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1429  Open or Short in Brake Pedal Load Sensing Switch  


DESCRIPTION

The brake pedal load sensing switch (brake with switch pedal sub-assembly) is turned on when the brake pedal is depressed with force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) detects if the brake pedal is depressed or not via this circuit.

DTC No. DTC Detection Condition Trouble Area
C1429 When the voltage at terminal +BS is 9.5 V or higher, an open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.
·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly) circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C285310E37
2.406,1.177 3.021,1.375 0.615,0.198 10 false FSW- 3.625,1.188 4.24,1.385 0.615,0.198 10 false FSW+ 2.146,1.25 2.375,1.448 0.229,0.198 10 false 1 4.115,1.26 4.344,1.458 0.229,0.198 10 false 2 2.229,2.135 2.5,2.333 0.271,0.198 10 false H2 2.208,2.344 4.76,2.719 2.552,0.375 10 false Brake Pedal Load Sensing Switch (Brake with Switch Pedal Sub-assembly) 5.469,1.25 5.74,1.448 0.271,0.198 10 false 23 5.802,1.385 6.375,1.594 0.573,0.208 10 false FSW+ 5.427,2.958 5.844,3.167 0.417,0.208 10 false A71 5.417,3.167 7.042,3.563 1.625,0.396 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


HINT:

When DTC C1425 and/or C1426 is output together with DTC C1429, inspect and repair the trouble areas indicated by DTC C1425 and/or C1426 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1425, or Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C1426).


PROCEDURE

1.READ VALUE USING GTS (BRAKE PEDAL LOAD SENSING SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Pedal Load Sensing SW Brake pedal load sensing switch (brake with switch pedal sub-assembly) / ON or OFF ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-


f.

Check that the brake pedal load sensing switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.



Result:
Result Proceed to
DTC C1429 is not output A
DTC C1429 is output B



A

B

3.INSPECT BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY
a.

Inspect the brake pedal load sensing switch (brake with switch pedal sub-assembly) (Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (w/ Brake pedal Load Sensing Switch)>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the H2 brake pedal load sensing switch (brake pedal support assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-23 (FSW+) - H2-2 (FSW+) Always Below 1 Ω
A71-23 (FSW+) or H2-2 (FSW+ ) - Body ground Always 10 kΩ or higher
H2-1 (FSW-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR