Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C0200/31  Front Speed Sensor RH Circuit  C0205/32  Front Speed Sensor LH Circuit  C1271/71  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272/72  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1275/75  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276/76  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The speed sensors detect wheel speed and transmit the signals to the ECU. These signals are used for control of the ABS control system. Each of the front and rear rotors has 48 serrations. When the rotors rotate, the magnetic field generated by the permanent magnet in the speed sensor induces an AC voltage.

Since the frequency of this AC voltage changes in direct proportion to the speed of the rotor, the frequency is used by the ECU to detect the speed of each wheel.

DTCs C1271/71, C1272/72, C1275/75 and C1276/76 can be deleted when the speed sensor sends a wheel speed signal or the Test Mode ends. DTCs C1271/71, C1272/72, C1275/75 and C1276/76 are output only in the Test Mode.

F102551E01
2.677,2.552 2.677,1.938 2.677,1.938 2.573,1.938 false 1.594,2.406 1.594,2.073 1.594,2.073 1.49,2.073 false 0.677,0.458 1.135,0.698 0.458,0.24 10 false Rotor 1.365,0.104 2.406,0.344 1.042,0.24 10 false Speed Sensor 2.219,0.521 2.771,0.74 0.552,0.219 10 false Magnet 2.323,0.958 2.979,1.188 0.656,0.229 10 false To ECU 1.885,1.854 2.688,2.083 0.802,0.229 10 false Low speed 0.76,1.99 1.583,2.24 0.823,0.25 10 false High speed 0.708,2.354 1.021,2.563 0.313,0.208 10 false +V 0.74,3.177 1.042,3.385 0.302,0.208 10 false -V 1.729,0.531 1.938,0.708 0.208,0.177 10 false N 1.979,0.531 2.188,0.708 0.208,0.177 10 false S 1.406,0.677 1.708,0.854 0.302,0.177 10 false Coil

DTC Code DTC Detection Condition Trouble Area
C0200/31
C0205/32
When any of the following is detected:
1.

At a vehicle speed of 10 km/h (6.2 mph) or more, an open or short in the sensor signal circuit continues for 15 second or more.

2.

Momentary interruption of the sensor signal from the abnormal wheel occurs 7 times or more.

3.

At a vehicle speed of 20 km/h (7 mph) or more, noise input continues for 5 seconds or more.

4.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

5.

When the following condition occurs 4 or more times after the ignition switch is turned off:

The speeds of the front wheels are lower than the rear wheel speed by 20 km/h (12 mph) or more for 20 seconds or more.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Front skid control rotor

·

Sensor installation

·

Skid control ECU


C1271/71
C1272/72
Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front skid control rotor


C1275/75
C1276/76
Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Front skid control rotor



HINT:
·

DTCs C0200/31, C1271/71 and C1275/75 are for the front speed sensor RH.

·

DTCs C0205/32, C1272/72 and C1276/76 are for the front speed sensor LH.



WIRING DIAGRAM

C374955E01
1.115,0.542 1.323,0.792 0.208,0.25 10 false 1 1.344,0.656 1.708,0.844 0.365,0.188 10 false FR- 1.25,0.958 2.156,1.198 0.906,0.24 10 false c1*1, B4*2 1.25,1.146 2.875,1.396 1.625,0.25 10 false Front Speed Sensor RH 2.031,0.635 2.354,0.854 0.323,0.219 10 false FR+ 2.417,0.542 2.656,0.792 0.24,0.25 10 false 2 1.115,2.271 1.323,2.521 0.208,0.25 10 false 1 1.333,2.396 1.688,2.615 0.354,0.219 10 false FL- 2.052,2.375 2.406,2.635 0.354,0.26 10 false FL+ 2.417,2.26 2.625,2.51 0.208,0.25 10 false 2 1.24,2.708 1.5,2.906 0.26,0.198 10 false B2 1.25,2.896 2.833,3.135 1.583,0.24 10 false Front Speed Sensor LH 0.208,3.844 1.594,4.073 1.385,0.229 10 false *1: except N04C-UH 0.188,4.313 1.406,4.583 1.219,0.271 10 false *2: for N04C-UH 1.948,3.844 3.063,4.031 1.115,0.188 10 false *3: Shielded 3.344,3.615 3.615,3.802 0.271,0.188 10 false *3 5.594,3.792 6.625,3.99 1.031,0.198 10 false A49*1, B53*2 5.583,3.99 6.813,4.219 1.229,0.229 10 false Skid control ECU 5.708,3.302 6.104,3.521 0.396,0.219 10 false FL- 5.427,3.177 5.698,3.365 0.271,0.188 10 false 5 5.708,2.396 6.094,2.646 0.385,0.25 10 false FL+ 5.427,2.281 5.698,2.469 0.271,0.188 10 false 6 5.708,1.979 6.125,2.198 0.417,0.219 10 false FSS 5.427,1.854 5.698,2.042 0.271,0.188 10 false 9 5.708,1.552 6.052,1.75 0.344,0.198 10 false FR- 5.438,1.438 5.708,1.625 0.271,0.188 10 false 3 5.708,0.667 6.063,0.865 0.354,0.198 10 false FR+ 5.427,0.542 5.698,0.729 0.271,0.188 10 false 4 4.417,3.615 4.688,3.802 0.271,0.188 10 false *3 4.417,1.865 4.688,2.052 0.271,0.188 10 false *3 3.344,1.865 3.615,2.052 0.271,0.188 10 false *3

PROCEDURE

1.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List mode on the GTS (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DATA LIST / ACTIVE TEST).

ABS / VSC / TRC:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front RH wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
FL Wheel Speed Front LH wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer



d.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the actual speed value when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

2.PERFORM TEST MODE (SIGNAL CHECK)

NG

5.CHECK SPEED SENSOR AND FRONT SKID CONTROL ROTOR SERRATIONS
2.PERFORM TEST MODE (SIGNAL CHECK)
a.

Perform sensor check in the Test Mode procedure (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.CHECK SPEED SENSOR AND FRONT SKID CONTROL ROTOR SERRATIONS

NG

5.CHECK SPEED SENSOR AND FRONT SKID CONTROL ROTOR SERRATIONS
3.CHECK SPEED SENSOR AND FRONT SKID CONTROL ROTOR SERRATIONS
a.
C401320E01
1.854,0.25 2.208,0.458 0.354,0.208 1.854,0.573 2.208,0.781 0.354,0.208 1.406,0.771 1.563,0.771 1.563,0.771 1.969,1.25 true 2.042,1.26 1.688,1.969 1.688,1.969 1.542,1.969 true 2.104,1.271 2.521,1.979 2.521,1.979 2.667,1.979 true 2.177,1.26 2.542,0.875 2.542,0.875 2.688,0.875 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.125,2.271 0.438,2.469 0.313,0.198 10 false *b 0.896,0.708 1.521,0.958 0.625,0.25 10 false 6 (FL+) 1.906,0.26 2.219,0.458 0.313,0.198 10 false A49 1.917,0.594 2.229,0.792 0.313,0.198 10 false B53 2.302,0.302 2.615,0.5 0.313,0.198 10 false *A 2.313,0.615 2.625,0.813 0.313,0.198 10 false *B 2.781,0.781 3.25,1.021 0.469,0.24 10 false 3 (FR-) 2.75,1.885 3.302,2.135 0.552,0.25 10 false 4 (FR+) 1.083,1.896 1.625,2.167 0.542,0.271 10 false 5 (FL-) 2.906,3.281 3.271,3.479 0.365,0.198 10 false GND 1,4.229 2.573,4.51 1.573,0.281 10 false 1 V/DIV, 2 ms./DIV

Connect the oscilloscope to the front speed sensor terminal of the skid control ECU.


b.

Check that a waveform is output by each sensor circuit when the tires are rotated.

OK:

The same waveform is output from all the 4 wheels and there is no noise or interference in the waveform.


Text in Illustration
*A except N04C-UH
*B for N04C-UH
*a Component with harness connected
(Skid Control ECU)
*b Normal signal waveform

HINT:
·

As the vehicle speed (wheel revolution speed) increases, the cycle of the waveform narrows and the output voltage becomes greater.

·

When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to speed sensor rotor's scratches, looseness or foreign matter attached to it.




Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

6.CHECK FRONT SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for at least 30 seconds.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C0200/31 and/or C0205/32) are not output A
DTCs (C0200/31 and/or C0205/32) are output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

6.CHECK FRONT SPEED SENSOR INSTALLATION
5.CHECK SPEED SENSOR AND FRONT SKID CONTROL ROTOR SERRATIONS
a.
C401320E01
1.854,0.25 2.208,0.458 0.354,0.208 1.854,0.573 2.208,0.781 0.354,0.208 1.406,0.771 1.563,0.771 1.563,0.771 1.969,1.25 true 2.042,1.26 1.688,1.969 1.688,1.969 1.542,1.969 true 2.104,1.271 2.521,1.979 2.521,1.979 2.667,1.979 true 2.177,1.26 2.542,0.875 2.542,0.875 2.688,0.875 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.125,2.271 0.438,2.469 0.313,0.198 10 false *b 0.896,0.708 1.521,0.958 0.625,0.25 10 false 6 (FL+) 1.906,0.26 2.219,0.458 0.313,0.198 10 false A49 1.917,0.594 2.229,0.792 0.313,0.198 10 false B53 2.302,0.302 2.615,0.5 0.313,0.198 10 false *A 2.313,0.615 2.625,0.813 0.313,0.198 10 false *B 2.781,0.781 3.25,1.021 0.469,0.24 10 false 3 (FR-) 2.75,1.885 3.302,2.135 0.552,0.25 10 false 4 (FR+) 1.083,1.896 1.625,2.167 0.542,0.271 10 false 5 (FL-) 2.906,3.281 3.271,3.479 0.365,0.198 10 false GND 1,4.229 2.573,4.51 1.573,0.281 10 false 1 V/DIV, 2 ms./DIV

Connect the oscilloscope to the front speed sensor terminal of the skid control ECU.


b.

Check that a waveform is output by each sensor circuit when the tires are rotated.

OK:

The same waveform is output from all the 4 wheels and there is no noise or interference in the waveform.


Text in Illustration
*A except N04C-UH
*B for N04C-UH
*a Component with harness connected
(Skid Control ECU)
*b Normal signal waveform

HINT:
·

As the vehicle speed (wheel revolution speed) increases, the cycle of the waveform narrows and the output voltage becomes greater.

·

When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to speed sensor rotor's scratches, looseness or foreign matter attached to it.



NOTICE:

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR INSTALLATION

NG

CLEAN OR REPLACE SPEED SENSOR OR SPEED SENSOR ROTOR

6.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C401322E01
0.833,1.635 0.833,0.781 0.833,0.781 0.99,0.781 true 0.708,2.5 0.948,2.844 0.948,2.844 1.094,2.844 true 0.188,0.146 0.5,0.344 0.313,0.198 10 false *1 1.063,0.698 1.802,0.896 0.74,0.198 10 false 8.5 N*m 1.146,2.771 1.458,2.969 0.313,0.198 10 false *2 0.49,3.031 0.802,3.229 0.313,0.198 10 false OK 2.646,3.031 2.958,3.229 0.313,0.198 10 false NG

Turn the ignition switch off.


b.

Check the front speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.


Torque:

8.5N*m{ 86kgf*cm , 75in.*lbf }


Text in Illustration
*1 Front Speed Sensor
*2 No clearance


Result:
Proceed to
OK
NG



OK

7.CHECK FRONT SPEED SENSOR TIP

NG

INSTALL FRONT SPEED SENSOR CORRECTLY

7.CHECK FRONT SPEED SENSOR TIP
a.

Turn the ignition switch off.


b.

c.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

8.INSPECT FRONT SPEED SENSOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

8.INSPECT FRONT SPEED SENSOR
a.
C215679E02
0.156,0.115 0.469,0.313 0.313,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
1 (FR-) - 2 (FR+) 20°C (68°F) 0.92 to 1.22 kΩ
1 (FR-) - Body ground Always 10 kΩ or higher
2 (FR+) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
1 (FL-) - 2 (FL+) 20°C (68°F) 0.92 to 1.22 kΩ
1 (FL-) - Body ground Always 10 kΩ or higher
2 (FL+) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Front Speed Sensor)

NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

REPLACE FRONT SPEED SENSOR

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except N04C-UH (for RH):
Tester Connection Condition Specified Condition
A49-4 (FR+) - c1-2 (FR+) Always Below 1 Ω
A49-4 (FR+) - Body ground Always 10 kΩ or higher
A49-3 (FR-) - c1-1 (FR-) Always Below 1 Ω
A49-3 (FR-) - Body ground Always 10 kΩ or higher

except N04C-UH (for LH):
Tester Connection Condition Specified Condition
A49-6 (FL+) - B2-2 (FL+) Always Below 1 Ω
A49-6 (FL+) - Body ground Always 10 kΩ or higher
A49-5 (FL-) - B2-1 (FL-) Always Below 1 Ω
A49-5 (FL-) - Body ground Always 10 kΩ or higher

for N04C-UH (for RH):
Tester Connection Condition Specified Condition
B53-4 (FR+) - B4-2 (FR+) Always Below 1 Ω
B53-4 (FR+) - Body ground Always 10 kΩ or higher
B53-3 (FR-) - B4-1 (FR-) Always Below 1 Ω
B53-3 (FR-) - Body ground Always 10 kΩ or higher

for N04C-UH (for LH):
Tester Connection Condition Specified Condition
B53-6 (FL+) - B2-2 (FL+) Always Below 1 Ω
B53-6 (FL+) - Body ground Always 10 kΩ or higher
B53-5 (FL-) - B2-1 (FL-) Always Below 1 Ω
B53-5 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK FRONT SKID CONTROL ROTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK FRONT SKID CONTROL ROTOR
a.

Turn the ignition switch off.


b.

Remove each front skid control rotor.


c.

Check the front skid control rotor.

OK:

No scratches, missing teeth, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

11.RECONFIRM DTC

NG

CLEAN OR REPLACE FRONT SKID CONTROL ROTOR

11.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Install the front skid control rotor.


c.

Install the speed sensor


d.

Reconnect the speed sensor connector.


e.

Reconnect the skid control ECU connector.



g.

Start the engine.


h.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for at least 30 seconds.


i.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C0200/31 and/or C0205/32) are not output A
DTCs (C0200/31 and/or C0205/32) are output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE SKID CONTROL ECU