Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C0210/33  Rear Speed Sensor RH Circuit  C0215/34  Rear Speed Sensor LH Circuit  C1273/73  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274/74  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1277/77  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278/78  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The speed sensors detect wheel speed and transmit the signals to the ECU. These signals are used for control of the ABS control system. Each of the front and rear rotors has 48 serrations.

When the rotors rotate, the magnetic field generated by the permanent magnet in the speed sensor induces an AC voltage.

Since the frequency of this AC voltage changes in direct proportion to the speed of the rotor, the frequency is used by the ECU to detect the speed of each wheel.

DTCs C1273/73, C1274/74, C1277/77 and C1278/78 can be deleted when the speed sensor sends a wheel speed signal or the Test Mode ends. DTCs C1273/73, C1274/74, C1277/77 and C1278/78 are output only in the Test Mode.

F102551E01
2.677,2.552 2.677,1.938 2.677,1.938 2.573,1.938 false 1.594,2.406 1.594,2.073 1.594,2.073 1.49,2.073 false 0.677,0.458 1.135,0.698 0.458,0.24 10 false Rotor 1.365,0.104 2.406,0.344 1.042,0.24 10 false Speed Sensor 2.219,0.521 2.771,0.74 0.552,0.219 10 false Magnet 2.323,0.958 2.979,1.188 0.656,0.229 10 false To ECU 1.885,1.854 2.688,2.083 0.802,0.229 10 false Low speed 0.76,1.99 1.583,2.24 0.823,0.25 10 false High speed 0.708,2.354 1.021,2.563 0.313,0.208 10 false +V 0.74,3.177 1.042,3.385 0.302,0.208 10 false -V 1.729,0.531 1.938,0.708 0.208,0.177 10 false N 1.979,0.531 2.188,0.708 0.208,0.177 10 false S 1.406,0.677 1.708,0.854 0.302,0.177 10 false Coil

DTC Code DTC Detection Condition Trouble Area
C0210/33
C0215/34
When any of the following is detected:
1.

At a vehicle speed of 12 km/h (7 mph) or more, an open or short in the sensor signal circuit continues for 1 second or more.

2.

Momentary interruption of the sensor signal from the abnormal wheel occurs 7 times or more.

3.

At a vehicle speed of 20 km/h (7 mph) or more, noise input continues for 5 seconds or more.

4.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

5.

When the following condition occurs 4 or more times after the ignition switch is turned off:

The speeds of the front wheels are lower than the rear wheel speed by 20 km/h (12 mph) or more for 20 seconds or more.


·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Rear skid control rotor

·

Sensor installation

·

Skid control ECU


C1273/73
C1274/74
Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear skid control rotor


C1277/77
C1278/78
Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Rear skid control rotor



HINT:
·

DTCs C0210/33, C1273/73 and C1277/77 are for the rear speed sensor RH.

·

DTCs C0215/34, C1274/74 and C1278/78 are for the rear speed sensor LH.



WIRING DIAGRAM

C374969E01
0.51,0.896 2.021,1.146 1.51,0.25 10 false Rear Seed Sensor RH 0.531,2.49 2.042,2.74 1.51,0.25 10 false Rear Seed Sensor LH 0.323,4.188 1.833,4.438 1.51,0.25 10 false *: Shielded 2.354,0.646 2.813,0.844 0.458,0.198 10 false RR+ 2.375,1.146 2.833,1.344 0.458,0.198 10 false RR- 2.375,2.177 2.833,2.375 0.458,0.198 10 false RL+ 2.396,2.75 2.854,2.948 0.458,0.198 10 false RL- 2.792,2.729 3.094,3 0.302,0.271 10 false p1 2.823,2.542 3.094,2.74 0.271,0.198 10 false 1 2.792,2.167 3.063,2.406 0.271,0.24 10 false p1 2.833,1.969 3.063,2.208 0.229,0.24 10 false 2 2.802,1.156 3.125,1.375 0.323,0.219 10 false p2 2.844,0.979 3.094,1.167 0.25,0.188 10 false 1 2.802,0.615 3.083,0.833 0.281,0.219 10 false p2 2.844,0.427 3.083,0.625 0.24,0.198 10 false 2 2.688,3.104 4.271,3.458 1.583,0.354 10 false Rear Skid Control Sensor Wire 6.01,3.146 6.469,3.344 0.458,0.198 10 false A47 6.01,3.365 7.146,3.615 1.135,0.25 10 false Skid Control ECU 6.125,2.76 6.583,2.958 0.458,0.198 10 false RL- 6.125,2.198 6.583,2.396 0.458,0.198 10 false RL+ 6.125,1.656 6.583,1.854 0.458,0.198 10 false RSS 6.125,1.177 6.583,1.375 0.458,0.198 10 false RR- 6.125,0.635 6.583,0.833 0.458,0.198 10 false RR+ 5.792,0.5 6.115,0.698 0.323,0.198 10 false 17 5.792,1.052 6.094,1.26 0.302,0.208 10 false 16 5.854,1.531 6.094,1.75 0.24,0.219 10 false 5 5.781,2.073 6.063,2.292 0.281,0.219 10 false 19 5.781,2.625 6.031,2.844 0.25,0.219 10 false 18 3.917,2.75 4.26,2.948 0.344,0.198 10 false Pp2 4,2.531 4.208,2.76 0.208,0.229 10 false 1 3.906,2.177 4.25,2.385 0.344,0.208 10 false Pp2 4.01,1.938 4.229,2.135 0.219,0.198 10 false 2 3.906,1.167 4.24,1.375 0.333,0.208 10 false Pp2 4.01,0.958 4.24,1.156 0.229,0.198 10 false 3 3.906,0.625 4.24,0.854 0.333,0.229 10 false Pp2 4,0.417 4.219,0.615 0.219,0.198 10 false 4 4.573,1.573 4.75,1.74 0.177,0.167 10 false * 5.25,1.563 5.427,1.729 0.177,0.167 10 false * 5.281,3.073 5.458,3.24 0.177,0.167 10 false * 4.573,3.073 4.75,3.24 0.177,0.167 10 false *

PROCEDURE

1.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List mode on the GTS (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DATA LIST / ACTIVE TEST).

ABS / VSC / TRC:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear RH wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
RL Wheel Speed Rear LH wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer



d.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the actual speed value when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

2.PERFORM TEST MODE (SIGNAL CHECK)

NG

5.CHECK SPEED SENSOR AND REAR SKID CONTROL ROTOR SERRATIONS
2.PERFORM TEST MODE (SIGNAL CHECK)
a.

Perform sensor check in the Test Mode procedure (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.CHECK SPEED SENSOR AND REAR SKID CONTROL ROTOR SERRATIONS

NG

5.CHECK SPEED SENSOR AND REAR SKID CONTROL ROTOR SERRATIONS
3.CHECK SPEED SENSOR AND REAR SKID CONTROL ROTOR SERRATIONS
a.
C401320E02
0.625,0.771 0.99,0.969 0.365,0.198 1,1.333 1.396,0.604 true 1.073,1.344 2.135,0.604 true 1.656,2.01 0.927,1.344 true 1.042,1.99 0.854,1.323 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.125,2.271 0.438,2.469 0.313,0.198 10 false *b 1.125,0.396 1.771,0.604 0.646,0.208 10 false 17 (RR+) 0.688,0.792 1,0.99 0.313,0.198 10 false A47 1.917,0.396 2.531,0.615 0.615,0.219 10 false 16 (RR-) 1.521,2.063 2.073,2.313 0.552,0.25 10 false 18 (RL-) 0.771,2.063 1.438,2.26 0.667,0.198 10 false 19 (RL+) 2.906,3.281 3.271,3.479 0.365,0.198 10 false GND 1,4.229 2.573,4.51 1.573,0.281 10 false 1 V/DIV, 2 ms./DIV

Connect the oscilloscope to the rear speed sensor terminal of the skid control ECU.


b.

Check that waveform is output by each sensor circuit when the tires are rotated.

OK:

The same waveform is output from all the 4 wheels and there is no noise or interference in the waveform.


Text in Illustration
*a Component with harness connected
(Skid Control ECU)
*b Normal signal waveform

HINT:
·

As the vehicle speed (wheel revolution speed) increases, the cycle of the waveform narrows and the output voltage becomes greater.

·

When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to speed sensor rotor's scratches, looseness or foreign matter attached to it.




Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

6.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for at least 30 seconds.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C0210/33 and/or C0215/34) are not output A
DTCs (C0210/33 and/or C0215/34) are output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

6.CHECK REAR SPEED SENSOR INSTALLATION
5.CHECK SPEED SENSOR AND REAR SKID CONTROL ROTOR SERRATIONS
a.
C401320E02
0.625,0.771 0.99,0.969 0.365,0.198 1,1.333 1.396,0.604 true 1.073,1.344 2.135,0.604 true 1.656,2.01 0.927,1.344 true 1.042,1.99 0.854,1.323 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 0.125,2.271 0.438,2.469 0.313,0.198 10 false *b 1.125,0.396 1.771,0.604 0.646,0.208 10 false 17 (RR+) 0.688,0.792 1,0.99 0.313,0.198 10 false A47 1.917,0.396 2.531,0.615 0.615,0.219 10 false 16 (RR-) 1.521,2.063 2.073,2.313 0.552,0.25 10 false 18 (RL-) 0.771,2.063 1.438,2.26 0.667,0.198 10 false 19 (RL+) 2.906,3.281 3.271,3.479 0.365,0.198 10 false GND 1,4.229 2.573,4.51 1.573,0.281 10 false 1 V/DIV, 2 ms./DIV

Connect the oscilloscope to the rear speed sensor terminal of the skid control ECU.


b.

Check that waveform is output by each sensor circuit when the tires are rotated.

OK:

The same waveform is output from all the 4 wheels and there is no noise or interference in the waveform.


Text in Illustration
*a Component with harness connected
(Skid Control ECU)
*b Normal signal waveform

HINT:
·

As the vehicle speed (wheel revolution speed) increases, the cycle of the waveform narrows and the output voltage becomes greater.

·

When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to speed sensor rotor's scratches, looseness or foreign matter attached to it.



NOTICE:

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

6.CHECK REAR SPEED SENSOR INSTALLATION

NG

CLEAN OR REPLACE SPEED SENSOR OR SPEED SENSOR ROTOR

6.CHECK REAR SPEED SENSOR INSTALLATION
a.
C401322E01
0.833,1.635 0.833,0.781 0.833,0.781 0.99,0.781 true 0.708,2.5 0.948,2.844 0.948,2.844 1.094,2.844 true 0.188,0.146 0.5,0.344 0.313,0.198 10 false *1 1.063,0.698 1.802,0.896 0.74,0.198 10 false 8.5 N*m 1.146,2.771 1.458,2.969 0.313,0.198 10 false *2 0.49,3.031 0.802,3.229 0.313,0.198 10 false OK 2.646,3.031 2.958,3.229 0.313,0.198 10 false NG

Turn the ignition switch off.


b.

Check the rear speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation bolt is tightened properly.


Torque:

8.5N*m{ 86kgf*cm , 75in.*lbf }


Text in Illustration
*1 Rear Speed Sensor
*2 No clearance


Result:
Proceed to
OK
NG



OK

7.CHECK REAR SPEED SENSOR TIP

NG

INSTALL REAR SPEED SENSOR CORRECTLY

7.CHECK REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

8.INSPECT REAR SPEED SENSOR WITH SKID CONTROL SENSOR WIRE

NG

CLEAN OR REPLACE REAR SPEED SENSOR

8.INSPECT REAR SPEED SENSOR WITH SKID CONTROL SENSOR WIRE
a.
C215680E02
1.542,0.323 1.906,0.542 0.365,0.219 0.125,0.063 0.417,0.271 0.292,0.208 10 false *a 1.604,0.344 2,0.573 0.396,0.229 10 false Pp2

Turn the ignition switch off.


b.

Connect the rear speed sensor connector.


c.

Disconnect the skid control sensor wire connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
Pp2-4 (Male) - Pp2-3 (Male) 20°C (68°F) 1.4 to 1.8 kΩ
Pp2-4 (Male) - Body ground Always 10 kΩ or higher
Pp2-3 (Male) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
Pp2-2 (Male)- Pp2-1 (Male) 20°C (68°F) 1.4 to 1.8 kΩ
Pp2-2 (Male) - Body ground Always 10 kΩ or higher
Pp2-1 (Male) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Skid Control Sensor Wire (Male))

NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

12.INSPECT SKID CONTROL SENSOR WIRE
9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A47-17 (RR+) - Pp2-4 (Female) Always Below 1 Ω
A47-17 (RR+) or Pp2-4 (Female) - Body ground Always 10 kΩ or higher
A47-16 (RR-) - Pp2-3 (Female) Always Below 1 Ω
A47-16 (RR-) or Pp2-3 (Female) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A47-19 (RL+) - Pp2-2 (Female) Always Below 1 Ω
A47-19 (RL+) or Pp2-2 (Female) - Body ground Always 10 kΩ or higher
A47-18 (RL-) - Pp2-1 (Female) Always Below 1 Ω
A47-18 (RL-) or Pp2-1 (Female) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK REAR SKID CONTROL ROTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK REAR SKID CONTROL ROTOR
a.

Turn the ignition switch off.


b.

Remove each rear skid control rotor.


c.

Check the rear skid control rotor.

OK:

No scratches, missing teeth, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

11.RECONFIRM DTC

NG

CLEAN OR REPLACE REAR SKID CONTROL ROTOR

11.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Install the rear skid control rotor.


c.

Install the speed sensor.


d.

Reconnect the speed sensor connector.



f.

Start the engine.


g.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for at least 30 seconds.


h.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C0210/33 and/or C0215/34) are not output A
DTCs (C0210/33 and/or C0215/34) are output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE SKID CONTROL ECU

12.INSPECT SKID CONTROL SENSOR WIRE
C375126E01
1.198,0.729 1.521,0.938 0.323,0.208 3.354,0.74 3.677,0.948 0.323,0.208 5.625,0.688 5.948,0.896 0.323,0.208 0.865,2.052 1.198,1.635 true 1.854,2.052 1.49,1.625 true 5.271,2.073 5.646,1.583 true 6.323,2.083 5.938,1.583 true 0.208,0.135 0.521,0.333 0.313,0.198 10 false *1 1.281,0.74 1.594,0.938 0.313,0.198 10 false p1 1.583,0.75 1.896,0.948 0.313,0.198 10 false *B 3.396,0.76 3.813,0.99 0.417,0.229 10 false Pp2 3.76,0.74 4.073,0.938 0.313,0.198 10 false *a 5.708,0.698 6.021,0.896 0.313,0.198 10 false p2 6.021,0.698 6.333,0.896 0.313,0.198 10 false *A 6.271,2.125 6.583,2.323 0.313,0.198 10 false RR+ 5.177,2.125 5.49,2.323 0.313,0.198 10 false RR- 1.802,2.115 2.115,2.313 0.313,0.198 10 false RL+ 0.76,2.115 1.073,2.313 0.313,0.198 10 false RL-

Text in Illustration
*A for RH *B for LH
*1 Skid Control Sensor Wire - -
*a Male - -

a.

Disconnect the rear speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
Pp2-4 (Male) - p2-2 (RR+) Always Below 1 Ω
Pp2-3 (Male) - p2-1 (RR-) Always Below 1 Ω
Pp2-4 (Male) - Pp2-3 (Male) Always 10 kΩ or higher
Pp2-4 (Male) - Pp2-1 (Male) Always 10 kΩ or higher
Pp2-4 (Male) - Pp2-2 (Male) Always 10 kΩ or higher
Pp2-4 (Male) or p2-2 (RR+) - Body ground Always 10 kΩ or higher
Pp2-3 (Male) or p2-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
Pp2-2 (Male) - p1-2 (RL+) Always Below 1 Ω
Pp2-1 (Male) - p1-1 (RL-) Always Below 1 Ω
Pp2-2 (Male) - Pp2-1 (Male) Always 10 kΩ or higher
Pp2-2 (Male) - Pp2-3 (Male) Always 10 kΩ or higher
Pp2-2 (Male) - Pp2-4 (Male) Always 10 kΩ or higher
Pp2-2 (Male) or p1-2 (RL+) - Body ground Always 10 kΩ or higher
Pp2-1 (Male) or p1-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE REAR SPEED SENSOR

NG

REPLACE SKID CONTROL SENSOR WIRE